iSys Minimod HD User manual

MINIMOD HD
Single DVB-T HDMI Modulator
USER MANUAL

Congratulations on your purchase of the Minimod HD Single DVB-T HDMI
Modulator
This ‘state of the art’ product, is an encoder. The video and audio inputs are taken from an
HDMI connection from the source device. The RF output is selectable and congured as a
DVB-T modulator.
Conguration is made through the integral control panel and OLED screen.
CONTENTS
1 Safety considerations page 3
2 Description of the different elements page 4
2.1 Back of unit explained page 4
2.2 Top of unit explained page 4
2.3 Location of the module page 4
3 Operating instructions page 5
3.1 Connecting to HDMI input page 5
3.2 Connecting to RF input page 5
4 Lock control page 5
5 Menu controls page 5
6 Parameters set up page 5
6.1 Output channel setup page 5
6.2 Setting up Constellation, FEC, guard interval, RF level page 6
audio bit rate, audio format
6.3 Channel name edit page 6
6.4 Setting up LCN, network name, audio pid, video pid page 6
PMT pid, programme number, video bit rate
6.5 OLED Display page 6
6.6 Factory reset page 6
6.7 Saving conguration to USB page 7
6.8 Firmware updates page 7
7. Declaration of Conformity page 7
8. Specications page 8
8.1 Encoder specications page 8
8.2 Modulation specications page 9
8.3 Rear panel specications page 10
8.4 Front panel specications page 10
8.5 Power and size specications page 11
2

1 SAFETY CONSIDERATIONS
1.1 Connecting to the mains supply
This product has to be connected to the mains supply. If there is the slightest doubt
concerning the type of connection available on the installation, please contact your supplier
of electricity. Before carrying out maintenance operation or modication of the installation,
the modulator has to be disconnected. Remark : only use the supplied power adaptor.
1.2 Over Voltage
An over voltage on the mains supply, can cause short circuits or re. Never overload the
power lines.
1.3 Liquids
This module should be protected from splashes. Please assure yourself that no containers
containing liquids are placed on this module. Also be aware of other persons splashing
liquids on the module.
1.4 Cleaning
Disconnect the module before cleaning. Use only a damp cloth without solvents.
1.5 Ventilation
In order to assure an adequate air circulation and to prevent overheating, the ventilation
holes should not be obstructed. The module may not be installed in a hermetically sealed
environment. Other electronic products or heat producing items may not be placed upon or
near the module.
1.6 Accessories
The use of accessories not manufactured by the
manufacturer can cause damage to the module.
1.7 Installation of the module
The module must be installed in a place well protected from direct sunlight. All measures
have to be taken to avoid installation in humid or sunny places. Do not install near heating
elements or other devices producing heat. Assure yourself that the module is placed at least
15 cm from other equipment which is susceptible to electromagnetic radiation. Do not install
the module on unstable items, a fall can cause physical or material damage. Always ensure
the module is mounted vertically and not on its side.
3

4
2.1 Back of unit explained
1 RF OUT: RF output
2 RF IN: RF input loop through
3 LTE: activates LTE lter
4 USB: USB connectivity for
upgrades/cloning
5 HDMI: HDMI input
6 DC: 12vDC input
2.2 Top of unit explained
7 Lock Button
8 Menu/OK: 1 x press menu, 2 x press OK
9 Left: backward selection
10 Right: forward selection
11 Down: List down selection
12 Up: List up selection
13 OLED Display
14 Power LED
15 Lock LED
16 Signal LED
15cm
15cm
123 4 5 6
7
8
9
10
11
12
13
2.3 - Location of the module
Leave a minimum space of at least 15cm above and below the product to guarantee an optimal
ventilation. The module should be mounted to assure a maximum natural ventilation. The module
should be xed to a wall using the wall xings on the module.
2 - Description of the different elements
16
15
14

5
3. Operating Instructions
You can connect your distribution system using either the HDMI or RF inputs:
3.1 Connecting to HDMI input
You can connect your HDMI source device such as SKY receiver, BluRay player or Apple
TV into the HDMI input of the modulator.
3.2 Connecting to RF Input
You can connect FreeviewTM digital terrestrial services into the RF input. If no such services
are featured in the system, then it is recommended a 75[W] F-Type terminator is tted
to this terminal. You can use a coax cable to connect the RF output to your distribution
system.
4. Lock control
This is a double use button.
You can use the (Lock) control button on the front panel to prevent
accidental tampering after installation. A single press will either lock or
unlock the installation controls. The LED will illuminate to indicate that the
panel is locked.
The button is also used for space/delete during the menu edit function channel name.
5. Menu/OK
To access the list of functions to programme the modulator, press the
menu button once. To save the settings, press twice to conrm.
6. Parameters Setup
The following parameters can be programmed:
6.1 Output Channel Setup
Press ‘Menu/OK’ button and the OLED screen will display: ‘freq/ch_**’.
Press the qor pbuttons to select the desired output channel. If you do
not want to setup other parameters, press ‘Menu/OK’ button and on the
display appears ‘save cong? yes ( * ) no ( )’. Press ‘Menu/OK’ again to
save the setting. To set up other parameters, press tor uto make your
selection. When all your selections are complete, press ‘Menu/OK’ twice to
save the settings.

set up..
LED off?
Factory
reset?
6
6.2 Setup Constellation, FEC, FFT, Guard Interval, RF Level, Audio Bit
Rate, Audio Format
Press ‘Menu/OK’ button and then use the tor ubuttons to select the
desired function.
Use qor pbuttons to select the correct value. When your selections are
complete, press ‘Menu/OK’ twice to save the setting
6.3 Channel ‘NAME’ edit
Press ‘Menu/OK’ button and then use the tor ubuttons to select the
‘name’ function. Press the pbutton to reveal the rst ickering character.
Then use the tor u buttons to change the character. To stop editing,
press the pbutton or press the qbutton to edit another character. Use
the button to delete the ickering character. The button also functions as
a 'space' button. To end the editing process, press ‘Menu/OK’ button twice and save the
‘name’ eld that you edited. To select other parameters, press the pbutton to end the
‘name’ editing function and use the tor u buttons to choose another programming
option.
6.4 LCN Setup, Network Name, Audio pid, Video pid, PMT pid,
Programme Number, Video Bit Rate.
Press ‘Menu/OK’ button and then use the tor ubuttons to select the
desired function such as ‘‘lcn’’. Press the pbutton to reveal the rst
ickering number. Then use the tor u buttons to change the number,
press the qbutton to select another number. To stop editing, press the p
button. To proceed to another function, press the tor ubuttons. When your selections
are complete, press ‘Menu/OK’ twice to save the setting.
6.5 Turn off OLED Display.
Press ‘Menu/OK’ button and then use the tor ubuttons to select the
‘led off?’ function. Press the pbutton to turn off the OLED display. Press
‘Menu/OK’ button again to activate the OLED display.
6.6 Factory Reset.
Press ‘Menu/OK’ button and then use the tor ubuttons to select the
‘factory reset’ function to resume to default settings. Press the pbutton
to start reset to default factory values . The display will appear ‘success!’
when the procedure is completed.

Upgrade
yes(x) no( )
7
6.7 Saving conguration to USB.
After adjusting the settings to the desired specications, these settings can
then be copied onto a USB drive and stored for future use. The information
can also be used for programming another MINIMOD HD device where
multiple units need to be programmed with the same specications. To save
this information, press ‘Menu/OK’ button and then use the tor ubuttons
to select the ‘save to usb’ option. Press the pbutton to start to start saving process and
then the display will appear ‘success!’ when the procedure is completed.
6.8 Firmware Updates.
This device is capable of being updated with periodic rmware releases.
These can be downloaded from www.antiference.co.uk and installed into
the modulator using the following procedure:
1. Download the appropriate rmware release from the Antiference
website.
2. Copy the ‘jedi.img’ le to a USB memory stick.
3. Turn the Minimod HD off.
4. Insert the USB memory into the USB port at the rear of the Modulator
5. Turn the Minimod HD on.
6. When the OLED display appears ‘upgrade yes ( * ) no ( )’ press the
‘Menu/OK’ button
The upgrade procedure will nish after approximately 10 seconds.
CAUTION
DO NOT turn the Minimod HD OFF while undergoing the rmware update procedure as this
may seriously damage the device.
7. DECLARATION OF CONFORMITY
We, Antiference LIMITED herewith declare that the modulator Minimod HD complies with all
essential requirements and any other applicable conditions set forth on directive 1999/05/
CE.
According to the WEEE (Waste Electrical and Electronic Equipment) EU Directive, do
not dispose of this product as household waste or commercial waste. Waste electrical
and electronic equipment should be appropriately collected and recycled as required by
practices established for your country. For information on recycling of this product, please
contact your local authorities, your household waste disposal service or the shop where you
purchased the product.
Date of issue: October 2014

8
8.0 Specications
8.1 Encoder
Processor Processor Frequency Host CPU: 200MHz 32Bit RISC
Security Processor: 200MHz 32Bit
Audio Processor: 200MHz 32Bit
Memory Ram DDRII 16Bit 512Mbit x 1 Embedded
Flash NOR Flash 32Bit x 1
Video Video Encoder ISO/IEC 11172-2 MPEG
ISO/IEC 13818-2 MPEG2 MP@HL
ISO/IEC 14496 MPEG4 compliant
Support SP@L3 to ASP@L5
ISO/IEC 14496-10 AVC,
HP@level 4.1, MP@level 4.1
H.264 prole 0
JPEG base-line, progressive
Aspect Ratio 16:9 wide screen, 4:3 letter box,
4:3 pan scan, support AFD(DTG, MingDTG)
Resolution 1080i,up to 1080p@30FPS

9
8.0 Specications
8.2 Modulation
Audio Audio Encoder MPEGI layer1/2,
MPEGII Layer II
AAC LC, HE-AAC v1/V2 (2- CH)
Output Frequency 174~233MHZ(VHF III),
Range 470 - 858 [MHz](UHF)
Output Impedance 50[W]
Input Impedance 50[W]
(loop to output)
Forward Error 1/2,2/3,3/4, 5/6, 7/8
Correction
Guard Interval 1/4,1/8,1/16,1/32
Constellations QPSK,16QAM,64QAM
RF Output Level Default: 90 dBμV
Αdjustable: 0 to -14 dB
0 to + 6 dB
Band Width 7MHZ(VHF),8MHZ(UHF)
FFT 2K,8K
Reed Soloman 202,188,T=8
Symbol Rate Range up to 31.668 MBPS
MER More than 35dB at Maximum RF Level
output

10
8.0 Specications
8.3 Rear Panel
RF Input Impedance:50 [W]
(Loop to Output) Input type: F-type female
RF Output Impedance:50 [W]
Output type: F-type female
USB Connector Number: 1
(software upgrade)
LTE ON/OFF
(Long Term Evolution Cut Off Frequency: 790MHZ
Filtering switch
HDMI Input Number: 1, High Denition
Media Interface HDMI
V1.4a
USB Connector Number: 1
Type: Host 2.0
Power DC Input X1 DC(12V, 2A)
Connector
8.4 Front Panel
Display Display 128x32 dots OLED Display
(IIC or SPI communication protocol)
LED Power & work state LED POWER/LOCKED/SIGNAL Indicator
Buttons Tactile switches x 6 Set Output channel
Up/Down/ Left, Right, FEC, CONSTELLATION, FFT,
Menu/OK,Lock Channel Name etc.