iSysmart SGZA10 User manual

Sysmarti
ZigBeeTM-Gas/Water Keeper
User Manual
Gas or Water Keeper
Model: SGZA10

Indicator LED
Binding key
Manual lever releaser
Lever
Power receptor
Installation holder
Gas / Water Keeper
SGZA10
Other ISysmart related devices
Switch controller:
Multiple/Scene controller SGZ503
Smoke detector SGZA01A/B/C/D

Introduction
SGZA10 is a router device in a network which permits other devices to join the network.
SGZA10 has two build-in features, depends on the configuration, the user may configure
it asa gas keeper or a water keeper.
As a gas keeper, the device is a controllable device which receive signal from a zone
device i.e. a smoke alarm to change the position of the leaver.
As a water keeper, the device can be controlled wirelessly from a paired remote controller.
SGZA10 is equipped with a manual override lever releaser and the enclosure is water
proof.
SGZA10’s operating pressure is 7 kgf. Valve rotation angle is 90°.
What is ZigBee?
ZigBee is a short range wireless transmission technology which defined for a minimum
complexity, low power consumption, low data rate, cost effective wireless solution. ZigBee
lies in between wireless markup technology and Bluetooth. ZigBee is based on
IEEE806.15.4 standard, the mutual co-ordination between thousands of sensors to
exchange data. Sensor to sensor or node-to-node communication is achieved through
relays of control data between devices with only a fraction of energy use which denoted
for highly transmission efficiency.
Note: Wireless communication, in some real use cases, can be limited by the signal
blockage. Please consult your service provider or place of purchase.

Setting up SGZA10 and
network
Setting Up Summary
(1) Configure the device to either as a gas or a water keeper
(2) Power up the device and network association
(3) Bind the device with other device where applicable (i.e. bind with an on/off remote or
with a smoke detector).
(4) How to use.
Step 1: Configure the device to either as a gas or a water keeper
SGZA10 can only either be a gas keeper type or a water keeper type device. Before you
move on to Step 2, you will need to go through the Restore to Factory Setting section to
configure the type of device you want -a gas keeper or a water keeper
The difference between the two device types is that if it is a gas keeper it will receive fire
alert message from the paired smoke detector of the security network to turn down the
leaver. If it is a water keeper it will receive on or off instruction from a remote controller by
the user.
Step 2: Power up the device and network association
To allow SGZA10 to function, it must first join to a ZigBee network either through a
coordinator or a router device. When it is given power it will automatically start searching
for an existed network. So before you give power to SGZA10 make sure it is within the
wireless coverage distance (~70 meters or less) and make sure first you have the
permit-join feature enabled either on a coordinator or a router device from the network
so that SGZA10 can detect and automatically join to the network through it;
*On how to enable permit-join please refer to the router or coordinator device user manual
Operation:
Step 1: First make sure you have opened up permit-join function (valid for 60 seconds) on
a coordinator or a router device in the network.
Step 2: Now plug in the power supplied provided to power on the SGZA10 device to let it

search for the network within reach.
Step 3: if join successful the indicator will stay solid light, otherwise the indicator is unlit.
Step 3: Device pairing as a gas keeper or a water keeper (Binding)
After the device has successfully joined to the network, the next step is to pair the device
with other device so that the paired device can control the keeper as required.
User may configure SGZA10 as either a gas keeper or a water keeper. Configuration is
described in Restore to factory setting in the manual.
As a gas keeper, SGZA10 is a controllable device which receive command signal from a
zone device i.e. upon receive a smoke alarm, it changes the position of the leaver. So pair
SGZA10with a smoke/gas detector.
As a water keeper, the device can be controlled wirelessly from a paired remote controller.
So pair SGZA10 with an On/Off remote controller.
The pairing operation is the same for both types, except for the types of device to pair
with.
Operation:
1. On the SGZA10, hold press the binding key for 3 seconds to send bind request to the air.
2. Likewise, do the same on the other device to exchange pairing request. (refer to its
user manual for device pairing procedure)
When binding is unsuccessful the indicator will give 10 fast flashes. If successful it will
give 5 slow flashes.

How to use
There are several ways to control the lever on SGZA10.
If SGZA10 is configured as a water keeper:
SGZA10 lever can be open or close through the remote controller.
Through the use of application software like ISysmart ZiG-BUTLER installed on a
computer/server, open or close instructions can be sent to and the device status can
be read and displayed.
On the fire event, the paired device sends command to water keeper and brings the
lever to ON position.
Manually release the lever lock button by pushing it inwards to release the lever so
you can move the lever either up or down.
If SGZA10 is configured as a gas keeper:
On the fire event, the paired device sends command to gas keeper and brings the
lever to down position.
Manually release the lever lock button by pushing it inwards to release the lever so
you can move the lever either up or down.
NOTE: When the Manual Lever Releaser Button (lever lock button) keeps inwards as the
figure below, please slightly move the lever to release the button.
Permit to join
SGZA10 is featured to be a router in the network. It permits other devices to join the
network. By default the router device SGZA10 does not allow permit-to-join function in
normal operation to protect the network from unexpected or unauthorized join attempt.
You will need to open up the permit-join on SGZA10 to allow new devices (a router or an
end device) to join.
Operation:

1. Short press the binding key once (less than 3 seconds).
2. The permit join is now enabled for 60 seconds and the indicator light will flash 60
times.
3. SGZA10 waits the new device to join in automatically. Please note that the maximum
waiting time to join is 60 seconds. Repeat the process if you missed the 60 seconds
period. Within the 60 seconds, short press the binding key when you want to disable
the permit-join finction.
Restore to factory setting
SGZA10 is capable of storing and saving includes network routing information. If you wish
to remove SGZA10 from the network and join to a new network, you would need to clear
the setting by simply reset the device to restore to the factory setting.
Operation:
Step 1. First remove the power from the device
Step 2. Hold on to the binding key. While doing so, power up the device again to give
power, until the indicator light flashes quickly then release the key. If you want the
keeper to be a gas keeper then go to Step 4 instead of 3 because by default SGZA10 is a
gaskeeper. But to program the keeper as water keeper then go to Step 3.
Step 3. To configure SGZA10 as water keeper, while the indicator is flashing quickly
from Step 2, short press the binding key once. This will configure it to become a
water keeper. Now go to Step 4.
(To make the device as a gas keeper, you should skip this step and go to step 5)
Step 4. Now the device is restored to the factory setting. Now power cycles the device to
put the device into network search mode.
(Note: by default SGZA10 is a gas keeper)

Clusters of Home Automation for SGZA10
Home Automation device feature is defined by the endpoint which contains functional
clusters. Table 1 lists clusters for the endpoint of SGZA10
Table 1: clusters for the endpoint of SGZA10
Server side
Client side
EP 0X01 (Device ID: On/Off Output (0x0002)
Basic(0x0000)
None
Identify(0x0003)
Groups(0x0004)
Scenes(0x0005)
On/Off(0x0006)
Commissiong (0x0015)
Attributes of the Basic Device Information attribute set
Identifier
Name
Type
Range
Access
Default
Mandatory
/ Optional
0x0000
ZCLVersion
Unsigned
8-bit integer
0x00 –
0xff
Read only
0X03
M
0x0001
ApplicationVersion
Unsigned
8-bit integer
0x00 –
0xff
Read only
0X0E
O
0x0002
StackVersion
Unsigned
8-bit integer
0x00 –
0xff
Read only
0X2E
O
0x0003
HWVersion
Unsigned
8-bit integer
0x00 –
0xff
Read only
0X0F
O
0x0004
ManufacturerName
Character
string
0 –32
bytes
Read only
iSysmart
O
0x0005
ModelIdentifier
Character
string
0 –32
bytes
Read only
SGZA10E
OR
O

0x0006
DateCode
Character
string
0 –16
bytes
Read only
20130122
O
0x0007
PowerSource
8-bit
Enumeration
0x00 –
0xff
Read only
0X04
M
0x0010
LocationDescription
Character
string
0 –16
bytes
Read/write
-
O
0x0011
PhysicalEnvironment
8-bit
Enumeration
0x00 –
0xff
Read/write
0x00
O

Important Maintenance Instructions
As the device is not water proof it is recommended to keep the device in a dry place.
Liquid and heavy moisture contains minerals that may oxidize the electronic circuitry. In
case of liquid spill, please leave the device to completely dry before storing or using.
Do not use or store the device in a dusty area. Dust may cause electronic parts to
destroy.
Do not use or store the device in an over heated place. Store in a hotter temperature
than the suggested maximum temperature may shorten the life span of the device; and
may damage the battery and causing the housing to deform.
Do not use or store the device in a very cold place than the suggested minimum
temperature. The water can be condensed inside the device when moving to an area that
is higher in temperature. This can severely damage the PCB board and circuitry. This may
shorten the life span of the device; damage the battery and cause the housing to deform.
Do not throw or strongly vibrate the device. This may damage connectivity of the
electronic parts and other sensitive components on the PCB board.
Do not use any strong chemical or washing to cleanse the device.
Do not use any coloring materials on any removable parts which my cause poor
connections and may keep the device from function properly.
All the above applies to the purchased products, battery and other packaged items. If any
unusable or damaged items are found please return the product to your nearest
authorized repairing center.