Italiana Camini LAYMA IDRO 18 Quick start guide

LAYMA IDRO 18-22
®
GB Installation, use and maintenance page 2
Pellet boiler stove

2
ENGLISH
The undersigned company with registered office in Via Vincenzo
Monti 47 - 20123 Milan (Italy) - Tax ID code and VAT number
00192220192
Hereby declares, under its sole responsibility, that:
The pellet boiler stove mentioned below complies with
EU Regulation 305/2011 and the harmonised EU standard
EN 14785:2006
PELLET BOILER STOVE, bearing the brand
ITALIANA CAMINI, named LAYMA IDRO 18-22
SERIAL NO.: Rating plate reference
LAYMA IDRO 18 Performance declaration: (DoP - EK n° 154):
LAYMA IDRO 22 Performance declaration: (DoP - EK n° 155):
Moreover, the company hereby declares that:
the LAYMA IDRO 18-22 wood pellet boiler stove satisfies the
requirements of the following European directives:
2014/35/EC - Low Voltage Directive
2014/30/EC - Electromagnetic Compatibility Directive
CONTENTS
Introduction and who the manual is for 3
Safety information 4
Dimensions 5
Technical data 6
Unpacking 7
Water circuit installation 10
Terminal board 13
Installation 14
Assembly of the cladding 18
Instructions for use 23
Maintenance 28
Troubleshooting 32

3
ENGLISH
MEANING OF SYMBOLS
In some parts of the manual the following symbols are
used:
INFORMATION:
failure to comply with these requirements
will compromise product use.
PLEASE NOTE:
carefully read and understand the
message in question, since failure to
follow the instructions in it could cause
serious damage to the product and put
the safety of those using it at risk.
OPERATING SEQUENCE:
follow the instructions for the operations
described.
The product is identified by a number, the “counterfoil”,
which is on the warranty certificate.
Please keep:
• the warranty certificate accompanying the product
• the purchase receipt given to you by the retailer
• the declaration of conformity given to you by the installer.
The warranty conditions are given in the warranty certificate
accompanying the product.
In Italy, commissioning by an authorised technician is
required by UNI 10683, and is recommended in all countries
to ensure best results from the product.
This consists in:
•checking the installation documents (declaration of
conformity) and the quality of the installation itself;
•calibratingtheproducttosuititsactualapplication;
•providing explanations to the end user and issuing the
complementary documentation (first ignition - commissioning
certificate).
Having the appliance commissioned properly ensures that it
will operate to best effect and in complete safety.
Proper commissioning is required for activation of the
manufacturer’s warranty.
The warranty is only valid in the country where the product
was bought.
If the appliance is not commissioned by an authorised
technician, the manufacturer will not provide warranty
service.
See the warranty booklet for details.
The above terms do not affect the dealer’s legal responsibility
for the legal warranty.
The warranty, however, covers only demonstrable
manufacturing defects and not, for instance, problems
resulting from improper installation or calibration.
Dear Sir/Madam
We thank you for and congratulate you on choosing our
product.
Before using it, we ask that you read this booklet carefully, in
order for you to be able to make the most of the functionality
in total safety.
This manual is an integral part of the product. Keep it with
care for the service life of the product.
For further information contact the RESELLER where you
purchased the product.
After unpacking the product, check the condition and
completeness of the contents.
In the event of any error, immediately contact the retailer
where the purchase was made, providing him with a copy of
the warranty booklet and the sales receipt.
The appliance must be installed and operated in compliance
with local and national law and European regulations. For the
installation, and for anything not specifically indicated in the
manual, observe local regulations.
The diagrams provided in this manual are for illustration
purposes only: they do not always strictly refer to your
specific model, and are not binding in any way.

4
ENGLISH
SAFETY INFORMATION
®
• The product is not designed for use by
people, including children, with limited
physical, sensory and mental abilities.
• The appliance is designed for cooking
purposes.
• The appliance is designed to burn
UNI EN ISO 17225-2 category A1 wood
pellets, in the amounts and manner
described in this manual.
• The appliance is designed for indoor use
and for environments with normal humidity
conditions.
• Keep the product in a dry place out of the
weather.
• For the legal and company warranties,
refer to the warranty certificate inside
the product: specifically, neither the
manufacturer nor the dealer are liable
for damage resulting from incorrect
installation or maintenance.
Safety risks may be caused by:
• Installation in unsuitable conditions. In
particular, conditions of fire hazard. DO
NOT INSTALL THE PRODUCT IN AREAS
SUBJECT TO THE RISK OF FIRE.
• Contact with fire and hot parts (e.g. glass
panel and pipes). DO NOT TOUCH HOT
PARTS and, when the stove is switched
off and still hot, always wear the glove
supplied.
• Contact with live electrical equipment
(internal). DO NOT ACCESS THE
INTERNAL ELECTRICAL EQUIPMENT
WHILE THE APPLIANCE IS POWERED
ON. Electrocution hazard.
• Use of improper ignition aids (e.g.
alcohol). DO NOT IGNITE OR BOOST
THE FLAME WITH FLUID SPRAYS OR
A FLAME TORCH. Serious risk of burns,
damage and injury.
• Use of fuel other than wood pellets. DO
NOT BURN WASTE MATTER, PLASTIC
OR OTHER MATERIALS THAN WOOD
PELLETS IN THE COMBUSTION
CHAMBER. The product may become
soiled, the flue may catch fire, and
environmental damage may ensue.
• cleaning the combustion chamber when
hot. DO NOT CLEAN THE COMBUSTION
CHAMBER WITH A VACUUM CLEANER
WHILE IT IS HOT. Risk of damage to the
cleaner and smoke in the room.
• Cleaning the fumes duct with cleaning
products. DO NOT CLEAN THE PRODUCT
WITH FLAMMABLE PRODUCTS. Risk of
fire or blowback.
• Cleaning the hot glass pane with
unsuitable cleaning products. DO NOT
CLEAN HOT GLASS WITH WATER.
ONLY USE RECOMMENDED GLASS
CLEANING PRODUCTS. Risk of cracking
and permanent, irreparable damage to
the glass.
• The storage of flammable materials at
a distance which is less than the safe
distances listed in this manual. DO NOT
PLACE LAUNDRY ON THE APPLIANCE.
DO NOT PLACE DRYING RACKS WITHIN
THE SAFETY CLEARANCE. Keep
flammable fluids away from the appliance.
Fire hazard.
• Blocking the aeration vents and air
intakes in the room. DO NOT BLOCK
THE AERATION VENTS OR FLUE. Risk
of smoke returning into the room with
consequent damage and injury.
• Use of the product as a support or ladder.
DO NOT CLIMB ONTO THE PRODUCT
OR USE IT AS A SUPPORT. Risk of
damage and injury.
• Use of the stove with the combustion
chamber door open. DO NOT USE THE
PRODUCT WITH ITS DOOR OPEN.
• Incandescent material projected from the
open door. DO NOT throw incandescent
material outside the appliance. Fire
hazard.
• Use of water in case of fire. CALL THE
AUTHORITIES if a fire breaks out.
• Never operate the product without water
in the circuit.
• Running it dry can damage it.
If you have doubts, please do not take any
action, but contact the retailer or the installer.
For reasons of safety, read the user instructions
included in this manual.
USER/INSTALLER

5
ENGLISH
DIMENSIONS
®
DIMENSIONS (cm)
62
60,5
120
120
62
Ø 5 cm
combustion air
Ø 8 cm
smoke outlet
14
47
14
USER/INSTALLER
The hydraulic connections depend on the
optional extras kit. Instructions are provided in the
“hydraulic installation” section.

6
ENGLISH
The manufacturer reserves the right to modify the product at his own discretion and without

TECHNICAL DATA
* The heatable volume is calculated for a house insulated pursuant to Italian Law 10/91 and subsequent amendments,
and a heating demand of 33 Kcal/m³ hour.
ELECTRICAL SPECIFICATIONS
Power supply 230 V AC +/- 10% 50 Hz
on/off switch yes
Mean absorbed power 80-60 W
Power absorption during ignition 320
Protection on mains power supply Fuse T2A, 250 Vac 5x20
Logic board protection Fuse T4A, 250 V AC 5x20
®
USER/INSTALLER
TECHNICAL SPECIFICATIONS as per EN 14785
The above data is for guidance only and was taken during the certification phase by a notified body under the
conditions specified by the standard.
LAYMA IDRO 22 LAYMA IDRO 18 LAYMA IDRO 22
LAYMA IDRO 18
Nominal power Reduced power
Available power 22,5 18,7 4,9 kW
Power available to water 20 16,3 3,8
Efficiency 92,7 93,3 95,1 %
CO emissions at 13% O20,012 0,013 0,007 %
Fumes temperature 114 101 54 °C
Fuel consumption 5,1 4,2 1,1 kg/h
Tank capacity 37 kg
Recommended draught 11 11 11 Pa
Autonomy 9 7 33 hours
Water content 20 l
Maximum operating pressure 2 bar
Maximum operating temperature 90 °C
Heatable volume * 585 485 m3
Fumes outlet diameter (male) 80 mm
Air intake diameter (male) 50 mm
Weight including packaging 260 kg
TECHNICAL DATA FOR RATING THE FLUE
which must in any case satisfy the requirements of this sheet and the installation instructions for the product
Nominal power
LAYMA IDRO 22 LAYMA IDRO 18
Fumes temperature at smoke outlet 137 122 °C
Minimum draw 0,01 Pa
Fumes flow rate 15,1 13,4 Rps

7
ENGLISH
UNPACKING
PREPARATION AND UNPACKING
The packaging materials are neither toxic nor noxious
and do not require special disposal.
The end user is responsible for storing, disposing of
and recycling them in a regulatory fashion.
Always move the stove vertically with
suitable equipment and in observance of
safety regulations.
Do not turn the package over, and handle
all parts requiring installation with care.
PACKAGING (details in the cladding paragraph)
The delivery consists of 3 packages:
• one (1) containing the stove’s frame
• one (2) containing the ceramic panels
• one (3) containing the metal sides
The package with the stove contains:
• warranty certificate,
• glove,
• this manual,
• power cable,
• air outlet grille for top (G),
• the removable handle for opening the combustion
chamber door with the small parts required for
fitting the cladding (M).
®
INSTALLER
G
M
1
2
3

8
ENGLISH
UNPACKING
TO REMOVE THE PRODUCT FROM THE PALLET
To remove the stove from the pallet (see diagrams below with numbers matching instructions)
1. remove the two brackets (screwed) to the front
2. remove two brackets (screwed) to the back of the stove
®
INSTALLER
Detail of grille (G) and pack with removable handle and small parts (M).
rubber elements
six screws because the pack
is shared with other products.
Use the three M4 screws for the
grille
12

9
ENGLISH
INSTALLER
INSTALLER
CONNECTING THE FUME EXHAUST PIPE
THE EXHAUST PIPE TO BE CONNECTED
TO THE FUME MOTOR IS LOCATED IN THE

The drawings are for guidance only, useful for
the installation, but they may not refer to the
specific model.
Open the lid of the pellet tank and take the pipe
Unscrew the three screws securing the centring bracket to the back of the stove
Push one end out from the back of the stove and fit the pipe onto the fume motor.
Reposition and the centring bracket screw it to the back of the stove
staffa di centraggio
®

10
ENGLISH
WATER CIRCUIT INSTALLATION
INSTALLER
®
R2 KIT Hydraulic connections template in mm
R-RW KIT Hydraulic connections template in mm
145
183
130
160 185
73 63 70 60
73 65 105
PIPE KIT Measurements in mm
side which lists the dimension occupied by the product on the leside
this edge identies the oor
HEATING DELIVERY
HEATING RETURN
SECURITY DISCHARGE
COLD H2O
THIS EDGE IDENTIFIES THE FLOOR
THIS EDGE IDENTIFIES THE DIMENSION OCCUPIED BY THE PRODUCT ON THE LEFT SIDE (see the technical manual)
COLD
COLD H2O
HEATING DELIVERY
HEATING RETURN
SECURITY DISCHARGE
THIS EDGE IDENTIFIES THE FLOOR
THIS EDGE IDENTIFIES THE DIMENSION OCCUPIED BY THE PRODUCT ON THE LEFT SIDE (see the technical manual)
ONLY FOR

11
ENGLISH
make sure that the swivel (nut)
on the two boiler stove outlet
pipes is closed
The product looks like the image below without any
kits.
WATER CIRCUIT INSTALLATION
PLUMBING
The products are equipped with closed expansion
tanks.
If the expansion tank is built into the
product, this does NOT ensure proper
protection against thermal expansion

Therefore, installers should assess whether
an additional expansion tank is needed,

ALL OTHER HYDRAULIC COMPONENTS MAY BE
INSTALLED WITHIN THE Boiler stove BY PURCHASING
A KIT OR IF PREPARED BY THE INSTALLER.
Plumbing depends on the type of system.
However, there are some “general rules”:
• The hydraulic system must operate at a pressure
between 1 and 1.5-2 bars at running temperature
(hot) in a closed vessel circuit.
• N.B.: The boiler stove SHOULD NOT be installed
in place of, for example, an open vessel installed
kitchen range without adjusting the expansion
system to closed vessel.
• The presence of an accumulator (tank) is
recommended but not mandatory. Its advantage
is that it releases the boiler stove from “sudden”
requests from the system and can be integrated
with other heat sources. It reduces fuel consumption
and increases the efficiency of the system. A puffer
of at least 20 l/kW is recommended.
• The return temperature of water to the boiler stove
must be higher than 50-55° C to prevent the forming
of condensation.
• An accumulator (tank) is needed to heat low-
temperature radiant panels and must be installed
according to the panel manufacturer’s instructions.
• The material used in the circuit must be suitable to
withstand overheating.
• The installer must determine whether or not to use
conditioned products. In Italy, refer to UNI 8065-1989
(Water treatment in heating systems for civil use).
• Direct plumbing to the radiators prevents proper
operation, owing to the small diameter of their pipes.
VENT
During normal operation the stove is
vented automatically. The need for manual
venting can only be assessed at initial
start-up by the technician
INSTALLER
®
swivel
We offer four internal kits (optional)
PIPE KITS
comprised of delivery and return pipe in the event that
the other components are installed externally (pump,
etc.).
KIT R (for Layma Idro)
for installation without instant DHW production.
KIT R2 (for Layma Idro)
For installation without instant DHW production with
system separator.
KIT RW (for Layma Idro 22)
for installation with instant DHW production Suggested
for 22 kW models only.
PRESSURE GAUGE
The boiler stoves have an electronic water pressure
gauge. There are no analogue pressure gauges. The
water pressure is shown on the display, (M7) as shown
in the diagram. An analogue pressure gauges can be
fitted as an optional extra.

12
ENGLISH
WATER CIRCUIT INSTALLATION
INSTALLER
®
OPTIONAL HYDRAULIC KITS All kits are supplied with instructions for their connection to the boiler stove.
The technicians have a dedicated paper template for each product. Make sure to use the correct template for the
model being installed.
Position the template flush with the floor and aligned with the left hand side of the outer edge boiler stove.
Remember to always observe the minimum installation distances, both from flammable materials and for maintenance.
HEATING AND INSTANT DHW
Compatible kits are:
• Pipe kit
• Kit R
• Kit RW
• Kit R2
The heat demand may arise from:
the environmental probe input (if the detected temperature falls 1 °C below the set temperature);
the flow switch, when the DHW tap is opened.
The heat demand is shown on the display by a radiator or a tap symbol.
HEATING AND DHW BOILER
Compatible kits for the boiler are:
• Pipe kit
• Kit R
The heat demand may arise from:
the environmental probe input (if the detected temperature falls 1 °C below the set temperature);
the demand for DHW from the thermostat/boiler probe.
With a DHW demand, the boiler stove pump is switched on if the temperature in the boiler stove is 5 °C higher than
the boiler temperature and the three-way valve diverts to DHW. The distribution pump is off.
HYDRAULIC INSTALLATION EXAMPLES

and the associated parameters should be set by the Technical Assistance Centre during

HEATING ONLY
Compatible kits are:
• Pipe kit
• Kit R
• Kit R2
The heat demand may arise from:
the environmental probe input (if the detected temperature falls 1 °C below the set temperature);
The heat demand is shown on the display by a radiator symbol.
With KIT PIPES :Please deactivate the pressure reading from the stove display
M8 => Password 11=> PR30 : 0,4 => 0

13
ENGLISH
TERMINAL BOARD
N° POLES POSSIBLE CONNECTIONS NOTES
1/2/3 External circulation pump connection to electrical
power supply (Earth, Neutral/Phase)
4Not wired
5/6 External thermostat
TERMINAL BOARD
There is a bracket with a terminal board and
2 cableways* on the back (remove the protective
cover fixed by two screws).
Examples of possible connection configurations are
given below.
* The cableways are provided in the pack above the
product structure. Based on the connections required
at the terminal board, break the knockout panel in the
terminal board cover for the cable to be wired and
secure it with the cable gland.
The poles are numbered on the product as below.
INSTALLER
®

14
ENGLISH
REMARKS ON INSTALLATION
Note that:
• installation must be carried out by authorised
technical personnel;
• the appliance must be installed and operated
in compliance with local and national law and
European regulations. The applicable Italian
regulation is UNI 10683;
• if installed in a condominium, the appliance must
be approved by the administrator.
We give some general instructions below, however
these do not obviate the need to comply with local
regulations and do not affect the installer’s liability for
the installation.
Checking the suitability of the installation
space
• The room must have a volume of at least 15 m3.
• The floor must be able to bear the weight of the
product and its accessories.
• Level the appliance.
• The appliance may not be installed in a bedroom,
bathroom or in the same room as other equipment
which draws air for combustion from the room
itself, or in any area with an explosive atmosphere.
Any extraction fans operating in the same room or
area as the product, may affect its draw.
• In Italy, check the compatibility pursuant to
UNI 10683 and UNI 7129 in the presence of gas
fired products.
INSTALLATION
Protection from heat and safety clearances
The surfaces of the building adjacent to the product
must be protected against overheating.
The insulation to be used will depend on the type of
surface in question.
The appliance must be installed in accordance with
the following safety instructions:
- minimum clearance at the sides and back of 15 cm
from flammable materials;
- no flammable materials may be kept closer to the
front of the appliance than 80 cm.
If connected to a wooden or otherwise flammable wall,
the flue must be insulated appropriately.
If installed on a flammable or combustible floor, or
which is not capable of bearing its load, use steel or
glass plates under the stove to distribute the load.
Contact the retailer for such optional equipment.
Positioning the product
The product is designed to operate in all climatic
conditions. In special circumstances, such as strong
wind, its safety equipment may switch the appliance
off.
Contact the authorised Edilkamin Technical Assistance
Centre.
INSTALLER
®
ADJUSTABLE FEET
The boiler stoves have adjustable feet to adapt to
uneven floors.

15
ENGLISH
FLUE SYSTEM
()
This chapter has been drawn up pursuant to European
regulations EN 13384, EN 1443, EN 1856 and EN 1457.
The installer must observe both these and any other
local regulations. This manual does not in any way
substitute such regulations.
The product must be connected to a flue system which
ensures that the fumes produced by combustion are
exhausted in complete safety.
Before positioning the appliance, the installer must
check that the flue is suitable.
FUMES DUCT, FLUE
The fumes duct (which connects the combustion
chamber smoke outlet with the flue) and the flue itself
must, among other regulatory requirements:
• receive the fumes from a single product (the outlets
of multiple appliances may not be conveyed into
a single flue)
• be routed vertically for the most part
• have no downwards sloping sections
• preferably have a circular internal cross section, or
with a ratio of the sides of less than 1.5
• terminate at roof level with a proper chimney pot:
the flue may not discharge directly on the wall
or into an enclosed space, even if the space in
question is open to the sky
• be made of material rated fire reaction class A1 per
UNI EN 13501 or analogous national regulations
• be certified, with a chimney plate if metal
• be of uniform cross section or vary in cross section
only immediately after the outlet, not at some mid
point of its length.
THE FUMES DUCT
Further to the general prescriptions for the fumes duct
and flue, the fumes duct:
• may not be made of flexible metal material
• must be insulated, if routed through unheated
areas or outdoors
• must not be routed through rooms where the
installation of combustion heat generators is
prohibited, there is risk of fire, or which cannot be
inspected
• must enable the recovery of soot and be open for
inspection
• have at most 3 bends with a maximum angle of
90°
• must have a single horizontal section with a length
of no more than 3 metres, depending on the draw.
Note, in any case, that long sections promote the
accumulation of dirt and are harder to keep clean.
INSTALLATION
INSTALLER
®

16
ENGLISH
THE FLUE
Further to the general prescriptions for the fumes duct
and flue, the flue:
• must serve solely to exhaust fumes
• must be correctly sized to satisfy the requirements
of fumes exhaust (EN 13384-1)
• should preferably be insulated, in steel with a
circular internal section. If rectangular, the corners
must have a radius of not less than 20 mm, with a
ratio of the internal dimensions of <1.5
• must normally be at least 1.5 metres in vertical
length
• must have a constant cross section
• must be waterproof and thermally insulated to
ensure a good draw
• must preferable have a collection chamber for
uncombusted matter and condensation
• if pre-existing, must be clean, to prevent the fire
hazard
• in general, we recommend fitting a tube inside the
existing masonry chimney if its diameter is greater
than 150 mm.
INTUBATED SYSTEM
Further to the general prescriptions for the fumes duct
and flue, the intubated system:
• must operate in negative pressure;
• must be open to inspection;
• must observe local regulations.
THE CHIMNEY POT
• must be windproof
• must have an internal cross section equivalent to
that of the flue and a fumes outlet at least double
that of the interior of the flue
• for dual flues (which should be spaced at least
2 m apart) the chimney pot receiving the fumes
from the solid fuel appliance or that from the
higher storey, must be at least 50 cm higher than
the other
• it must extend beyond the back flow zone (in Italy,
refer to UNI 10683 point 6.5.8.)
• it must allow for maintenance of the chimney.
INSTALLATION
INSTALLER
®
COMBUSTION AIR INTAKE
In general, we suggest two ways to ensure a proper
flow of combustion air. The air must be drawn from
outside*
Please remember to also ensure air exchange for
heating and glass cleaning air, etc.
Indirect air intake
The boiler stove draws the air from outside through a
hole at the rear.
Install an air outlet at floor level with an effective surface
area (net of the screen or other protections) of at least
80 cm2(10 cm in diameter).
To prevent draughts, we recommend installing the
intake behind the product or behind a radiator.
Installing it in front of the appliance will create
unpleasant draughts.
Direct air intake **
Install an air intake of effective surface area (net of the
mesh or other protective equipment) equal to the cross
section of the air intake at the back of the product.
Connect the air intake to the appliance’s air intake
with a tube (which may also be flexible). Increase the
diameter of the pipe if the pipe is not smooth: assess
any load loss.
We recommend not exceeding a 3 m length, keeping
in mind the draw of the flue. For each curve, up to a
maximum of two curves, the length should be reduced
by 1 m. Assess whether or not to increase the diameter
of the pipe.
* The air maybe drawn from an adjacent room only if:
• the flow is taken from permanent and unobstructed
openings communicating with the outdoors;
• the air pressure in the adjacent room is never
lower than that of the outdoor pressure;
• the adjacent room is not a garage. subject to fire
hazard, a bathroom or bedroom;
• the adjacent room is not a shared room in the
condominium.
In Italy, UNI 10683 provides that ventilation is sufficient
even if a pressure difference between the outdoors
and indoors of no more than 4 PA is guaranteed
(UNI EN 13384-1). The installer who issues the
declaration of conformity is responsible for ensuring
these conditions.
** Direct connection to the air intake will not make the
product airtight. It is therefore necessary to additionally
ensure an air intake from within the room where the
product is installed (i.e. for glass cleaning).

17
ENGLISH
CHECKINGTHEELECTRICALCONNECTIONS
(the power socket must be located in an
easy to access position)
The stove is equipped with an electrical power cord or
connection to a 230V 50 Hz socket, preferably with an
electromagnetic switch.
Variations in voltage of more than 10% can compromise
the operation of the stove.
The electrical system must be compliant; check the
operation of the earth in particular.
Edilkamin is not responsible for malfunctions resulting
from an improperly earthed system.
The power line must be of adequate section for the
power of the appliance.
The power cable must not come into contact with the
flue or other hot parts of the stove.
Power up the stove by setting its switch from 0 to 1.
There is a 4 A fuse on the socket with switch located at
the rear of the stove.
INSTALLATION
switch
fuse compartment power supply
INSTALLER
®

18
ENGLISH
COVER
Description  Quantity
Ceramic tile on combustion chamber door (1) 1
Ceramic lower front panel (2) 1
Metal side panel (3) 2
Ceramic top (4) 1
INSTALLER
The metal grille for the top is in the neck of the stove structure with three M4 screws, washers and two rubber
elements for fastening.
* Small parts:
• M4 screws with washers for securing ceramic parts
• M5 screws with washers and rubber elements for the metal side panels
• cable glands for the terminal board at the rear
®
Small parts*
1
4
2
3

19
ENGLISH
COVER
INSTALLER
1. Open the combustion chamber door using the
removable handle (M) and screw in the ceramic tile
(using the two M4 screws and washers), as shown in
the figure and detail image on this page.
Fitting the ceramic tile to the combustion
chamber door (1)
®
1
1
M
1

20
ENGLISH
COVER
INSTALLER
1. With the combustion chamber door open, unscrew
the two screws to remove the metal lower front panel.
2. Screw the ceramic tile onto the metal lower front
panel (using two M4 screws and washers).
Fitting the ceramic lower front panel (2)
3. Screw the metal lower front panel - 2(with ceramic
lower front panel attached) onto the stove.
The panel can be adjusted right/left, by adjusting the
screws in the slots.
®
1
2
2
3
2