ITLONG ITL-TC0100 User manual

Card Authorization Reader
User Manual
Products Model：ITL-TC/DK0100
Last revision date：9 Sept 2016

I
Catalogue
CHAPTER ⅠPRODUCT INTRODUCTION ...................................1
1.1 PRODUCT INTRODUCTION...............................................................1
1.2 DESIGN STANDARD ........................................................................1
1.3 SPECIFICATION ...............................................................................1
1.4 EXTERNAL DIMENSION...................................................................2
CHAPTER ⅡINSTALLATION INSTRUCTION..........................2
2.1 CARD AUTHORIZATION READER USB PLUG IN..............................2
2.2 CHECK............................................................................................3
2.3 INSTALLATION OF APPLICATION SOFTWARE ...................................3
2.4 STATUS DESCRIPTION OF MACHINE................................................4
CHAPTER ⅢTROUBLESHOOTING...............................................4
CHAPTER IVAPPENDIX...................................................................5

1
Chapter ⅠProduct Introduction
1.1 Product Introduction
ITL-DK0100/ITL-TC0100 comply with ISO/IEC-14443A International
Standard ，supporting ISO-14443A cards and other compatible
contact-less RFID IC cards including Mifare® 1,Non-contact IC
card,CPU card.
As an integral part of the Card Function System, the Authorization
machine needs to be connected to a computer equipped with
communication interface software (provided by our company).Computer
software control the authorization machine through USB port to realize
the function to read and write the non-contact IC card and CPU.
1.2 Design Standard
The product is designed to meet the GB / T 18239-2000 integrated circuit
general specifications of (IC) card reader.
1.3 Specification
Power supply:USB Port ,5V，working currents ＜200mA.
External Dimension:L140mm *W 90mm * H17.5mm.
USB Cable:1.5m.
Card Type:Mifare® 1 IC card, CPU Card.
Response time:≤0.5s.
Read distance:0～30mm.
Usage Environment:
Temperature:-15℃～50℃.

2
Relative Humidity: 20%～90% non-condensing.
Storage Environment:
Temperature:-40℃～70℃.
Relative Humidity: 20%～90% non-condensing.
Communication mode:USB,HID module.
1.4 External Dimension
See the card authorization reader picture as below:
Pic 1.1
Chapter ⅡInstallation Instruction
2.1 Card Authorization Reader USB Plug in
Plug the authorization reader USB in the computer USB interface. If this
is your first time using it, the computer taskbar would prompt "正在安装
设备驱动程序软件（单击此处查看状态）", After clicking it, the
installation state will be displayed. See the figure 2.1 as below. After

3
completion, as shown in Figure 2.2.
Figure 2.1 The Installation of device driver software
Figure 2.2 The device is ready
2.2 Check
After the driver is loaded normally, it can be viewed in Device Manager.
Look up: My Computer (Right click) → Management → Device
Manager →Anthropological input device → HID-compliant device
The HID-compliant device is authorization reader.
2.3 Installation ofApplication Software
Install the company's corresponding application software, enter the
software, you can read and write the IC card through the company's
application software.

4
2.4 Status Description of Machine
LED1(Red light):After stable operation ,the card authorization reader
will be controlled by the software.
LED2 (Yellow light): After stable operation ,the card authorization
reader will be controlled by the software.
LED3 (Green light):After stable operation, the card authorization
reader will be controlled by the software.
LED4 (Blue light):System status indicator. It will flash in 0.5Hz when
the authorization.
BZ1 (Buzzer):Power on, it will bleep once. After stable operation ,the
card authorization reader will be controlled by the software.
Chapter ⅢTroubleshooting
The following are some possible phenomenons and simple inspection
methods.
Symptom 1: The data communication connection between the computer
and the authorization reader can not be eatablished correctly.
Cause of issues
Troubleshooting method
Multiple HID devices connected
connect 1 device
Communication line connection
is unstable or wrong
Reconnect the authorization
reader correctly
USB interface damage
Returned to factory for repair
Symptom 2: The card can not be operated correctly by the
authorization reader.
Cause of issues
Troubleshooting method

5
Interference around the device
Eliminate the interference
sources
Mismatched card
Use the correct card
multiple cards in the card
induction area
1 IC card only
Chapter IV Regulatory
Note：This equipment has been tested and found to complywith the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits aredesigned to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Caution:Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Warning:This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and(2) this device must accept any interference
received, including interference that may cause undesired operation.