ItsaGoal 8' X 4' ANTI-VANDAL GOAL Install guide

COMPONENTS
STEEL POST SECTIONS
76mm
2
1
x
x
CROSSBAR SECTION
UPRIGHT SECTION
E
F
76mm
2
x
BRASS BARREL LOCK
B
2
x
KEY
A
GROUND SOCKET
WITH PLASTIC CAP
C2
x
REMOVABLE ‘D’ SUPPORT
G2
x
4
x
M8 WINGNUT AND HEX
SCREW - 40mm LONG
H
8mm
1
x
GOAL NET
NET SUPPORT
SUPPLIED IF PURCHASED WITH GOAL.
SUPPLIED IF PURCHASED WITH GOAL.
NET
16
x
NYLON ARROW HEAD NET
FIXING with attached LOCKING PIN
D
NYLON
Ensure locking pin
Is inserted Fully in
the posts
DO NOT THROW THE LOCKING
PINS AWAY
3
Push locking pin
Down centre of
Arrow Head
2
Insert Arrow Head
into Holes on
posts
1
NET
G
H
H
REMOVABLE ‘D’
SUPPORTS
ARE AVAILABLE SEPARATELY
TO PURCHASE VISIT www.soccertackle.com
To hold and support the Net.
REMOVABLE ‘D’ SUPPORTS AND NET ARE OPTIONAL
!
8' X 4' ANTI-VANDAL GOAL
STEEL
ANTI-VANDAL FITTING
INSTRUCTION
TEL: [phone]SPARE PARTS
B
A
TWIST AND LOCK
E
E
D
ANTI VANDAL SECURE SYSTEM
APPLY GREASE
INSIDE BARREL
LOCK HOUSING
APPLY WD40
INSIDE KEY LOCK
AT START & END
OF SEASON
Our innovative Anti-Vandal system.
WE RESERVE THE RIGHTS TO AMEND THE SPECIFICATIONS OF OUR SOCCER
PRODUCTS IN THE INTEREST OF CONTINUED DEVELOPMENT. YOUR PRODUCT
THEREFORE MAY DIFFER LIGHTLY TO THOSE ILLUSTRATED. E&OE
WORLDWIDE © COPYRIGHT 2001 ITSA GOAL POSTS LTD,
ALL RIGHTS RESERVED A REGISTERED DESIGN
European & USA Patent GB 2423260
FITTING THE NET FIXINGS
INSERT NET FIXINGS INTO HOLES ON REAR
OF GOAL. A LOCKING PIN IS LOCATED ON
THE TOP OF THE NET FIXING.
DO NOT THROW THE
LOCKING PINS
PUSH LOCKING PIN FULLY INTO THE NET
FIXING , THIS WILL SECURE IT IN PLACE.
REMOVING THE NET FIXING
THE LOCKING PIN CAN BE PUSHED
COMPLETELY THROUGH THE FIXING BY
USING A ROD LESS THAN 4MM IN DIAMETER
(SUCH AS A BLUNT NAIL). WHEN PUSHED
FULLY THROUGH THE PIN WILL DROP INSIDE
THE POST AND ALLOW THE FIXING TO BE
PULLED OUT. SAVE THE LOCKING PIN IF
FIXINGS ARE TO BE REUSED.
PUSH FIXING INTO
8.8mm Dia. HOLES
ON POSTS
ENSURE PIN LOCKING
IS INSERTED
FULLY TO SECURE
NET FIXING
PUSH LOCKING PIN
DOWN CENTRE OF FIXING
E
F
F
C
C
D

Installation of ground Sockets
1. Mark out Pitch & Check pitch is square before installing sockets.
For assistance in doing this please visit( www.itsagoal.net
2. When you are sure the pitch is square mark the position of the centre of the goal
line (see overleaf)
NOTE: half the width of the goal either side of the goal line centre point = Upright
positions
I.e. A 24’ x 8’ goal will have uprights positioned 12’ either side of the
centre point
3. Put one upright in at one end of the marked out pitch first. Ensure that they are at
the correct height and that they are vertical not leaning to the side, backwards or
forwards. (Use a level and timber supports to hold in place until concrete has
hardened. THE MEASUREMENT MUST RUN TO THE INSIDE OF
THE UPRIGHTS & TO THE UNDERSIDE OF THE CROSSBAR.
24’
12’
8’
12’
Centre Point
4. Once the socket has hardened and secured, you can use this with the upright
inserted to support the rest of the goal whilst the second socket is concreted in
place.
Position the second upright in to it’s socket and fit the crossbar, bolt or lock in place.
Ensure the goal is lined up correctly on your goal line. I.e. Place both uprights in with
the crossbar secured in place The first upright and crossbar attached will help to
support the newly concreted second upright with crossbar attached while setting.
NEVER INSTALL GOALS WITH CHILDREN PRESENT
5. Level up the second upright as before & check crossbar is running parallel to the
ground. Support second upright with timber (to prevent leaning) until concrete has
hardened.
If you have not created a drainage hole in concrete - push rod through before
concrete hardens off. It is a good idea to use a level on the crossbar also and then
take any imperfections out in the ground level
after the goal has completely settled Never install or dismantle goalpost with children
in the near vicinity . If children are likely to be drawn to your installation. Stay with
goal until concrete has fully set. Do not take any risks.
Secure
Post
Second
upright
Timber/
Supports
These goals must only be used with the correct ground sockets provided by I.T.S.A.
Goal. They must be concreted in position correctly as shown and as per the relevant
safety standards. BS EN748 - BS 8462 & BS 8461 (Goal Maintenance).
You can contact our technical director on mobile [phone] for any help on
installation.
12
3
45
o
45 max.
40mm min.
350mm
1 Upright
2 Sport Surface
3 Concrete Block
4 Ground Socket
5 Drainage Hole
NET SUPPORT POLE SOCKET
Installation to European
Standards BS EN748
1m
net
support pole
Goal post foundations
(see separate
diagram overleaf)
Recommended position of net support poles as per BS EN 748
Plan view of goal
2m
crossbar
B
B
A
A
FOR FURTHER INFORMATION & ADDITIONAL FITTING
INSTRUCTIONS VISIT OUR WEB SITE:
www.itsagoal.net
MEADOWHALL SOCCER CENTRE
FERRARS ROAD, TINSLEY, SHEFFIELD S9 1RZ
TEL: [phone]
Standard-Socketed installation BSEN748.cdr
GROUND SOCKET Installation diagram
12
6
7
3
Radius
100mm
45
40mm min.
500mm
o
45 max.
1 Upright
2 Sport Surface
3 Concrete Block
4 Ground Socket
5 Drainage Hole
6. Socket Bolt
7. Pea Gravel
Note ‘Socket bolt’ must
be inserted to prevent
ingress of soil into
ground socket. Put a
dab of grease on it and insert
the screw into the hole and just leave it in place. At any
time in the future it can be locked'.
BOX STYLE SHAPE
(with three support poles
and extra cords)
NET
SUPPORT
POLE
STANDARD SHAPED NETS CAN ALSO BE USED WITH NET SUPPORT POLES.
TYPES OF NETS & SUPPORTS AVAILABLE FOR SOCKETED GOALS Nets and Supports sold Separately.
BOX STYLE SHAPE
(with two support poles
and extra cords)
STANDARD SHAPE
With removable
‘D’ supports.
NET
SUPPORT
POLE
!
USE GROUND PEGS TO PEG NET
GROUND
PEG
FITTING BOX NETS
ATTACH THE NET TO THE GOAL FRAME , TO THE CROSSBAR FIRST
THEN BOTH UPRIGHTS.
WE ADVISE TWO CORDS BE FIXED TO THE NET AT EACH POLE
POSITION. ONE CORD IS MEASURED TO THE POLE POSITION WITH A
PLASTIC CLIP AND THE OTHER IS LONGER AND LOOSE TO TAKE DOWN
THE NET SUPPORT POLE AND TENSION AND TIE OFF THE NET.
TO INSTALL THE NET, CLIP TO EACH NET SUPPORT POLE THEN LIFT
POLE INTO THE GROUND SOCKET AND THIS WILL LIFT NET INTO
PLACE AND FORM THE BOX NET.
USE THE SECOND CORD TO TENSION THE NET. FINALLY PEG OUT THE
BASE OF THE NET OR USE GROUND FRAMES TO WEIGHT NET TO THE
GROUND
MAKE SURE YOU HAVE THE LONGEST
LENGTH (8’) - A , FITTING ONTO THE
UPRIGHT &THE SHORTEST LENGTH
(5’) - B, TO THE GROUND.
WARNINGS
MAKE SURE NO CHILDREN ARE
PRESENT AT ANY TIME DURING GOAL
INSTALLATION, REMOVAL OR ASSEMBLY
CHECK THE POSITION OF ANY UNDERGROUND SERVICES BEFORE
EXCAVATION. WE TAKE NO RESPONSIBILITY FOR ANY DAMAGE OR
INJURY CAUSED IN THIS MANNER.
WARNING: DO NOT TOUCH OVERHEAD SERVICES WITH POLES OR ANY
PARTS. CHECK THE POSITION OF ANY OVERHEAD SERVICES WHEN
SETTING UP OR DISMANTLING. POWER LINES, TELEPHONE CABELS
ETC.
DO NOT SWING ON ANY NET SUPPORT POLE OR
GOAL POST SECTION.
IT IS RECOMMENDED THAT AFTER USE GROUND
SOCKET HOLE ARE COVERED WITH OUR CAPS
THAT ARE SOLD SEPARATELY.
TO AVOID DAMAGE WHEN DISMANTLING THE GOAL FOLLOW THESE
GUIDELINES: DO NOT USE ANY COMPONENTS PARTS IF THEY ARE
DAMAGED OR BROKEN. IT IS ADVISABLE IN EXTREME WINDY
CONDITIONS TO DISMANTLE THE GOAL AND STORE AWAY.
A
B
B
A
TWIST AND LOCK
SOCKET CAPS
ARE AVAILABLE SEPARATELY
www.soccertackle.com
TO PURCHASE VIST
To cover and protect
Ground Socket.
www.soccertackle.com
TO PURCHASE VIST
Protects paintwork at
the base of the
upright.
GOALPOST
PROTECTOR TAPE
AVAILABLE SEPARATELY