Iveco RL4-UCON7-500 User manual

The interface can offer：Reverse camera insertion, several other videos like 2D/3D-360 surround view、night
view、DVR 、phone mirror link 、and support maxim 4 video inputs.
Suitable cars: fits 2019 IVECO with 7inch Monitor.
Features
➢One simple daughter PCB insertion, it works also when the external box is not connected.
➢This total unit can be manually powered on by ACC【BATT and Manual ACC connected to cigarette lighter, thus would be
no current leakage at all.
➢The front video can be easily enabled by short press on the keypad. A hold or long press will make the inputs switched to
other video sources.]
➢A “Reverse-in” trigger wire to manually switch to the Rev-In video.
➢The high quality image processor has the advantages of stable and low power consumption. All the components are
automotive specific and work stably in the range of -40~+85℃.
RL4-UCON7-IVE interface installation manual191115_V20191017

Accessories
Note: spare parts 7 and 8 are equipped with one more set than the actual installation.
What's in the Package
No.
Name
Qty
No.
Name
Qty
1
Interface box
1
5
External switch
1
2
External PCB
1
6
4 Video RCA Cable
1
3
CAN-Harness
1
7
0.5*40*200A ribbon
2
4
LVDS Cable
1
8
0.5*40*80A ribbon
0.5*40Pin board
2
②
③
①
⑤
④
⑥
⑦
⑧

Connections
Reverse-IN
should be
connected to
reversing light
Connect the
purple wire
“Manual ACC”to
the car ACC。
Connect BATT and
GND to the original
car.
Connect the two ribbons to the two sockets on
the external PCB. The external PCB sockets are
signed OUT and IN. Connect the ribbon IN to the
socket IN and ribbon OUT to socket OUT（the
ribbon connected to the 40pin external PCB is IN).
The PCB installation will show how to connect the
ribbons and boards。
Small buttons to switch
video by long or short
press

Installation Procedure
1、IVECO 7inch Monitor HU and one external
PCB, one LVDS Cable.
2、Remove screws, then the rear can be
opened.
3、Pay attention to take the OEM ribbon from
the Monitor as the above picture shows.
4、Put the OEM ribbon to the external PCB
and connect interface’s 200mm ribbon connect
to OE socket .
5、Extend the two ribbon from the Head Unit
gap, fix the ribbon to the Head Unit by
tape.
6、Remove the screws and put our external
PCB on the HU, then fix the external PCB by
the screws as the above picture shows.

DIP Setting
1) DIP-4 Setting
DIP up=off DIP down=on
DIP
on
off
default
1/2/3
No function
off
4
=Down for USB update, otherwise =UP.
2) DIP-8 Setting
DIP up=off DIP down=on
DIP
on
off
default
1
Front camera =ON
Front camera = OFF
off
2
AV1 =ON
AV1=OFF
on
3
AV2 =ON
AV2=OFF
on
4
/
/
off
5
Rear camera installed, when
REVERSE-IN=12V, inserted
camera picture will be
displayed.
OE rear camera installed.
when REVERSE-IN=12V, OEM
picture will be displayed.
on
6/7/8
/
/
off
Note
A. Add video after switching through the external small button.
Short press：image shows OEM→then front camera→then OEM.
Long press [Hold]：image shows OEM →image shows AV1→image shows AV2→image shows OEM (when
AV1\AV2 is fully open)
Such as:
1) when dialing 1 is closed, short press cannot switch forward view. Only when dialing 1 is open can it be
switched.

2) DIP2=OFF: Long press the small button can image shows OEM →image shows AV2→image shows OEM.
3) DIP3=OFF: Long press the small button can image shows OEM →image shows AV1→image shows OEM.
B. The green line "REVERSE IN" on the video line can be connected with the reversing light line to switch
the reversing image.
Parameters
#
Name
Parameters
1
Video input amplitude
0.7Vpp ,75 Ω
2
Sync amplitude
3~5Vpp,5K, negative pulse
3
Reverse-out:
12V,3A[max]
4
Reverse-IN:
threshold：3V
5
Av1 , cam video amplitude.
0.7Vpp,75 Ω
6
Av1 , cam format
NTSC/PAL/SECAM automatic
7
Power consumption
3.6W [0.3A @12V]
8
Standby current
< 10uA
9
10
Temperature
-40 ~ +85C
11
size
15.22cm * 9cm * 2.1cm