Iwata SHRED-X SMALL User manual

SHREDDER USER MANUAL
SMALL

3
2
INSTALLATION
Mount the shredder securely to the rim of the waste basket. (FIGURE 1)
A socket-outlet should be near the equipment and be easily accessible.
Connect the power cord to any standard 220 volt AC outlet.
This shredder includes a built-in safety mechanism that requires the shredder to be
correctly mounted on the supplied wastebasket. It is not designed to operate with any other
wastebaskets. An activation switch located on the head unit automatically shuts off the shredder when
it is lifted or removed. The supplied wastebasket activates this switch, which allows the shredder to be
operable. Lining the wastebasket with a plastic bag will interfere and may keep the shredder from
functioning.
Caution: Crosscut shredders have very sharp exposed blades on the underside.
Use care when mounting the shredder on the wastebasket.
OPERATION
AUTO / ON :
This setting allows the shredder to be automatically started by inserting paper into the
shred opening. Always feed the paper in as straight as possible. When the paper has
passed through, the shredder will automatically stop. (FIGURE 2)
OFF:
This setting turns off all features of the shredder. For safety reasons, we recommend that
you leave the shredder in the "Off" position whenever the shredder is unattended or not
in use. (FIGURE 2)
REV (REVERSE
):
In the unlikely event of a paper jam, the reverse setting can be used to help clear the cutters
of paper that has not passed through. Never attempt to clear a jam by using the reverse
function until you have emptied the wastebasket. (FIGURE 2)
The green LED light indicates the shredder in “On” and ready for use.
I
O
R
CONTINUED NEXT PAGE
Paper Shredder
Operating Instructions
Installation
Operation
Maintenance
Troubleshooting
Service Center
Warning
Limited Warranty
Sheet Capacity
Paper Shred Size
Paper Entry Width
Credit Card & CD Capacity
Voltage
10 Sheets of 20lb. bond paper*
3/16 in. x 1 15/32 in. pieces
(0.48 cm x 3.7 cm pieces)
9.0 in / 22.9 cm
1 at a time
220V~60Hz / 2 A
* ONE FOLDED SHEET OF PAPER EQUATES TO 2 SHEETS OF PAPER
Heavier paper, humidity or other than rate voltage may reduce capacity.
Using the switch located on the unit, select one of the following settings by sliding the switch either
left or right. (FIGURE 2)
FIGURE 1
FIGURE 2 FIGURE 3
Features a CD/DVD destroyer (FIGURE 3):
Do not hold CD/DVD with finger thr ough the center ring while feeding into the
shredder . Serious injury may occur. Never feed more than one credit card or CD/DVD at a time.
1) Hold the CD/DVD by the edge and feed one at a time, releasing when shredding begins.
2) Shredder will stop when the entire disc has been destroyed.
LED Status indicators:
Power On
(green light)
Paper Overload
(red light)
Shredder Not Aligned
(red light)

5
4
MAINTENANCE
Crosscut shredders require regular oil lubrication for optimal performance and extended lifespan. We
recommend you oil your shredderonce a month. Yourbasicvegetable or cookingoil (nothingflammable
or petroleum based) can be drizzled onto a few sheets of paper and fed into the shredder.
DO NOT SPRAY OR KEEP ANY AEROSOL PRODUCTS IN OR AROUND THE SHREDDER.
DO NOT USE CANNED AIR.
Be sure to periodically empty the wastebasket to avoid overloading and damaging
the cutting mechanism.
CLEANING:
• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.
• Do not clean or immerse shredder in water. Having the unit wet may result in damage or
malfunction to the electrical components. If the shredder happens to get wet, be sure to completely
dry the unit immediately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to
the product.
TROUBLESHOOTING
If there is a problem with your shredder, check below for the symptoms and steps to resolve. If you
continue to have problems, contact customer support at our Service Center. DO NOT ATTEMPT TO
REPAIR BY OPENING THE SHREDDER HEAD. This will completely void the product warranty.
The shredder does not work at all.
a) Make sure the unit is plugged in and that the outlet it is plugged into is in good working order.
b) Overheating with extended use: In the event that the shredder has shred continuously
beyond the maximum running time and overheating, the unit will automatically shut off. If this
happens, switch the shredder Off for 30 minutes or longer before resuming normal operation.
c) This shredder includes a built-in safety mechanism that requires the shredder to be
correctly mounted on the supplied wastebasket. It is not designed to operate with any other
wastebaskets. An activation switch located on the head unit automatically shuts off the shredder when
it is lifted or removed. The supplied wastebasket activates this switch, which allows the shredder to be
operable.
d) If using a plastic bag to line the wastebasket, please remove it since this may be the cause of the
shredder to not operate properly.
e) The activation sensor of the shredder is located near the center of the feed slot. Be sure to feed
directly into the center area to activate the machine (especially applies to smaller pieces of paper or
credit cards).
The shredder runs in "Rev" mode but not in "Auto" mode.
a) While in "Auto" mode, the motor will not start running until paper is inserted into the feed slot. Set
the unit to "Auto" and insert paper to be shredded. It is normal for the motor to run for a moment after
setting it to "Auto" but it should stop until paper is inserted. The trigger that activates the shredder in
Auto mode is located directly in the center of the slot. If the paper you are inserting is narrow, it may
not be hitting the switch. It is possible that the trigger, which activates the shredder, has become
blocked with paper. Insert an index card, directly in the center of the feed slot, and apply force. This
will usually clear any paper blocking the switch and force the switch closed.
CONTINUED NEXT P AGE
Never shred large paper clips, window or insulated envelopes, continuous forms,
newsprint, transparencies, laminated documents, cardboard, any items with
adhesives, hard materials or plastic (except Credit Cards and CDs).
This shredder will shred staples and small paperclips. It is recommended that you remove paper clips
whenever possible to extend the lifespan of your shredder.
Only shred credit cards by feeding them ver tically into the middle of the entr y,
releasing when shredding begins. Never feed more than one credit card at a time.
DO NOT ACTIVATE REVERSE FUNCTION WHILE SHREDDING CREDIT CARDS OR CDS.
Overfeeding the shredder: Shredding beyond the specified sheet capacity can result in extensive
damage to the shredder
. Overfeeding will strain the machine and quickly wear and break the cutting
blades and internal components.
Overheating with extended use: In the event that the shredder has shred continuously beyond
the maximum running time and overheating, the unit will automatically shut off. If this happens, switch
the shredder Off for 30 minutes or longer before resuming nor
mal operation.
OPERATION

7
6
Avoid touching the document
feed opening with hands.
Product is not intended for use by
children (product is not a toy).
Do not insert foreign objects into
the document feed opening.
Do not spray or keep any
aerosol products in or around
shredder.
Avoid loose clothing or jewelry
touching the document feed
opening.
Avoid getting hair near the
document feed opening.
WARNING
- RISK OF FIRE. Never use any petroleum based or flammable oils or lubricants in or around the
machine as some oils can combust causing serious injury.
- NEVER dispose of flammable chemicals or materials that have come into contact with flammable
chemicals (for example, nail polish, acetone, gasoline) in the shredder basket.
- Never shred plastic (except credit cards and CDs), any hard materials, continuous
forms, newsprint, or anything with adhesives including labels and envelopes.
- Do not hold CD/DVD with finger through the center ring while feeding into the
shredder . Serious injury may occur.
- A socket-outlet should be near the equipment and be easily accessible.
- Always turn the shredder off and unplug the power cord from the AC outlet before cleaning it,
moving it, or emptying the waste basket.
- Never let the wastebasket become full. This will lead to shredded material being pulled back up into
the shredder and cause jams.
- Never place the shredder near water or any heat source.
- Keep wastebasket emptied so that the shredder output is not impeded.
- Do not use the shredder if the power cord is damaged in any way.
- Do not attempt to service this product yourself as doing so may expose you to sharp cutting blades
and/or electricity and will void the manufacturers warranty.
- Never try to clean or clear the shredder blade.
- Never shred beyond the specified sheet capacity. May result in extensive damage to the machine.
SERVICE CENTER
If you have any questions in regards to the operation of this shredder or in need of a spare part,
please contact our service center at:
TROUBLESHOOTING CONTINUED
How to clear a paper jam in the shredder.
a) Switch the shredder over into Reverse (REV) mode. While in Reverse, the shredder will back up and
loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively
clear the machine. When jammed paper is loosened or removed, switch back to the Auto-On mode to
continue shredding. Repeat steps if needed.
b) With stubborn situations where the reverse function does not help, you may loosen the jammed
paper with shredder oil (cooking oil is acceptable, nothing aerosol). Start by drizzling oil into the
blades where the paper is jammed. Let it soak for about 30 minutes to completely saturate. Return the
shredder back to Auto-On mode. If required, a rigid sheet of cardstock (old greeting card, folded file
folder, or a sheet torn from a cereal box) can be fed into the shredder to help push the jammed paper
through.
The shredder is constantly running while in “Auto (On)” mode.
a) It is possible that the activation sensor, which starts the shredder, has become blocked with paper.
Inser
t an index card or any rigid sheet of cardstock (old greeting card, file folder, or a sheet torn from
a cereal box), directly in the center of the feed slot, while applying force to help push the jammed
paper through. This will usually clear any paper blocking the activation sensor and feed entry.
LEARN MORE
Landlines.: 8282-5049; 8282-5098
Mobile Nos. 0908-8908597; 0917-3079188
Email: [email protected] / [email protected]
Website: www.colentco.com