iWorX Roam Wireless User manual

ROAM Wireless
Roam Wireless Manual
The iWorx ROAM Wireless is a wearable system designed to provide long-term recording and
unrestricted movement. The recording device easily attaches to the subject with standard electrodes.
The protective case doubles as a charging station. The system wor s with both Windows and MacOS
via standard USB interface. Data can be quic ly analyzed with the included LabScribe analysis
software or exported directly for other processing. The ROAM Wireless devices allow for hours of
continuous recording with an untethered reach of 20 feet.
Equipment
The list below indicates all the products included. If you find any missing items please notify iWorx
Systems as soon as possible.
Roam Wireless Peripheral
Charger Box
USB Receiver Dongle
USB charging cable
Disposable Electrodes
Specifications
Device Channels
IXR-ECG 1 ECG channel,
1 Respiration Channel
IXR-ECGA 1 ECG channel,
1 Respiration Channel,
3-axis Accerelrometer
IXR-B1 2 ECG/EMG channels
IXR-B1A 2 ECG/EMG channels
3-axis Accerelrometer
IXR-B2 2 ECG/EMG channels
IXR-B2A 2 ECG/EMG channels 3-axis Accerelrometer

ROAM Wireless
Specifications for all Roam Wireless Devices
Battery capacity 11 mAhr
Battery life > 8hrs
Range upto 2 ft
Sampling Speed 5k samples per sec. aggregate
Resolution < 6 µV
Weight 16.8g
Dimensions 44.2mm x 42.7mm
Charging the Device
1. The ROAM case is designed to charge the
device. Be sure that the ROAM Wireless
device (the part with the iWorx logo and
serial number) is secure in the case.
2. Ta e the provided charger cable and
connect one end to the USB port of your
computer.
3. Connect the other side of the charger cable
to the port located on the front of the case.
4. If done correctly, a light will illuminate on
the ROAM Wireless device. A red light
indicates that the unit is charging. A green light indicates a full battery. It ta es approximately
two hours for complete charging.
5. Please charge the device before each use. In storage, the device goes to sleep to conserve
energy, but it is still using power to monitor the accelerometer, so that it can be wo en up when
needed.
Device Set Up
1. Remove the ROAM Wireless device from the charging box.
2. Plug the USB receiver dongle into the USB port of the computer.
◦The LED on the receiver will will blin green while it loo s for the transmitter. Once the
transmitter is found, the light will stay solid green to show that the connection has been
made. Move the ROAM device transmitter or tap the transmitter if receiver dongle doesn’t
convert to solid green light.

ROAM Wireless
Consumables
The silver-silver chloride electrodes are the part of the instrument that is in contact with the s in by
ma ing electrical contact between the s in and the sensor. Silver-silver chloride electrodes are the best
electrodes for recording EMG signals. The electrodes are disposable and should be replaced after each
use.
iWorx offers three types of silver-silver chloride electrodes differing based on the width of the adhesive
material and position of the electrode in it.
Picture Description (click part number to go to
website)
A-GC-7165
Foam solid gel electrodes
50 x 54mm
150 per pac age
A-GC-7165P
Pediatric foam solid gel electrodes
3 mm
15 per package
A-ELEC-E-30
Foam solid gel electrodes
35 / 53mm
Latex and PVC free
Diaphoretic / Hypoallergenic
C-ISO-GNE5
Platinum Subdermal Needle Electrode (48 inches)
10mm length, 30-gage
Set of five
*for animal use

ROAM Wireless
Proper s in preparation is important to get a good signal and avoid artifacts.
•Before applying electrodes, ma e sure the s in surface is clean and dry:
•Abrade the s in with an abrasive cream, such as NuPrep, to remove dead s in.
•Alternatively, you can also clean s in with an alcohol wipe and let it dry, but this is not as
efficient as the abrasive cream.
Tips:
It is easier to connect the electrodes to the snap cable before placing the electrode on the subject.

ROAM Wireless
Registration and Software Installation
Downloading Software
1. The equipment comes with a Temporary User Name and Password,
so that you can immediately get started with your system by
downloading and installing the software. It is strongly encouraged
that you register as a User on the iworx.com website with your
own UN and PW.
2. Go to iworx.com - then clic the “User Area Registration” lin
from the customer area of the main page (grey box half way down
the page on the right hand side).
3. Complete the registration form ma ing sure to enter information in
all the required fields.
4. You will receive an email from iWorx when your registration is complete, which may ta e upto
24 hours. Until then use the temporary username and password
5. Log on as an iWorx user on the website and download LabScribe Software.
a. Go to www.iworx.com - then clic the “Software” tab from the top menu selections.
b. Clic “Downloads” and enter your username and password.
c. Clic “Research”.
d. Select the correct “Complete Installer” for your operating system.
e. Follow the directions for saving to your hard drive. Double-click for saving directly to your
computer; right-click to save to another location.
f. For Mac Users, download the “Pac age” and follow the prompts to install.
**You need Administrative Access to your lab computers to install the software to the lab
computers. If you do not have Administrative Access, please contact your IT department.
Note for T Depts. doing the installation: Users must be able to save to the local drive. They will

ROAM Wireless
need permissions to write to C:\Users\USERNAME\AppData\Local\LabScribe
oading Setting Group
1. Once installed you should see a LabScribe shortcut on your des top.
2. Clic the shortcut and open LabScribe.
3. Load Settings Group if necessary (you only have to do this the first time you start LabScribe)
4. Clic Settings → Load Group
5. Choose Research Settings → Choose your equipment from the list.
6. Choose the group you wish to load. And clic “Open”
7. The window will close and you will be bac to the original LabScribe recording window
Choosing the Settings
1. On the LabScribe Recording window – Clic "Settings"
2. You should now see a list of Experiments. They may be in folders.
3. When you clic on any lab exercise two windows will open –
1) a PDF of the lab exercise setup for that experiment
2) a LabScribe recording window with the settings needed to run the experiment
earning to use abscribe
Various tutorial videos for using LabScribe are available on the iworx website,
at http s ://www.iworx.com/tutorials

ROAM Wireless
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance nformation
Unique dentifier: IXR-ECG, IXR-ECGA, IXR-B1, IXR-B1A, IXR-B2, IXR-B2A, iWireR-ECG,
iWireR-ECGA, iWireR-B1, iWireR-B1A, iWireR-B2, iWireR-B2A
Responsible Party – U.S. Contact nformation
iWorx Systems Inc
62 Littleworth Road
Dover, NH 03820
Telephone number : [phone]
nternet contact information : https://iworx.com
FCC Compliance Statement (e.g., products subject to Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Intended Usage
iWorx Systems Inc. instruments, components, and accessories are designed for educational and
research oriented life science applications and investigations. iWorx Systems Inc. does not condone the
use of its instruments for clinical medical applications. Instruments, components, and accessories
provided by iWorx Systems Inc. are not intended for the diagnosis, cure, mitigation, treatment, or
prevention of disease.
Furthermore, the unit is intended for research and teaching applications. The fact the this product is
IEC 60601-1 compliant in no way means that it is to be used for medical purposes. It was tested to the
60601-1 standard because it’s a more rigorous form of testing. The unit is not intended to be used as a
medical device, i.e. it’s not to be used as a diagnostic or therapeutic equipment.

ROAM Wireless
Intended Environment:
The unit should only be used in a classroom or laboratory setting.
Storage Conditions:
•Temperature - 0°C to 40°C
•Humidity - 0 to 70%
Operating Conditions:
•Temperature - 10°C to 30°C.
•Humidity - 0 to 60%
Disposal:
The user has two options, either send it bac to the manufacturer or send to a recycling center.
Explanation of Symbols:
Direct Current
Ground
Warranty Information:
No modification of this equipment is allowed. The unit contains no customer serviceable parts. If a
problem occurs, contact your iWorx representative. Repair, if required, will be completed at iWorx
Systems, Inc. The unit is protected by a 3-year warranty, and if the product is opened by any one other
than iWorx personnel the warranty will be void.

ROAM Wireless
Company Information:
Headquarters
iWorx Systems, Inc.
62 Littleworth oad
Dover, NH 03820
Phone: [phone]
Fax: [phone]
Website: www.iWorx.com