J. A. Roby FORGERON CUISINIERE User manual

March 1
st
, 2015
CAN/ULC S627-M00
UL 1482
CAN/CSA STD B415.1-10
Instruction Manual
490, rue de l'Argon
Quebec, CANADA G2N 2C9
Tel.: [phone] Fax : [phone]
FORGERON CUISINIERE
FORGERON

March 1
st
, 2015
Table of contents
Introduction..................................................................................3
Nameplate. ..................................................................................4
Appliance Dimensions. ...............................................................5
Installation....................................................................................6
Floor protection....................................................................... 6
Floor protection plate minimum dimensions.....................6
Clearances of the stove until the floor plate protection....7
Minimums clearances to the non-combustible material. ...... 8
Assembly before installation..............................................9
Legs installation. ................................................................9
Warmer stove Assembly (Optional)..................................9
Fan and Snap disc box installation.................................11
Firebricks installation............................................................12
General stove installation steps. .....................................14
Chimney connector installation............................................15
Mobile home installation....................................................... 17
Chimney installation, General steps....................................18
Inside Masonry Chimney, Vertical Installation................18
Outside Vertical Installation.............................................19
Cathedral Vertical Installation..........................................19
Offset Installation .............................................................19
Vertical Installation...........................................................20
External combustion air source. ..........................................21
Exterior Air Intake pipe......................................................21
Installation of Air Intake Pipe...........................................21
Air Inlet Obstruction .........................................................21
Stainless steel deflector replacement..................................22
Stainless steel tubes replacement...................................23
Stainless steel tubes Installation.....................................23
Operating Instructions ...........................................................24
Primary and secondary air admission control...............24
Lightning fire.......................................................................24
First fire. ................................................................................24
Keep a fire.............................................................................24
Fans Controls........................................................................24
Maintenance. .......................................................................25
Ash Removal....................................................................25
Ash Disposal.....................................................................25
Creosote Formation. ........................................................25
Chimney Inspection..........................................................25
Chimney Sweeping..........................................................25
Door care..........................................................................25
Air Tighten Adjustment.....................................................26
Cleaning up glass.............................................................26
Uninstalling and installing door........................................26
Broken glass replacement...............................................26
Fiberglass rope replacement...........................................26
What to do in case of Chimney Fire.................................27
Annexe 1...............................................................................28
Door assembly..................................................................28
Annexe 2...............................................................................29
Parts that can be replaced...............................................29
J. A. ROBY LIMITED LIFE WARRANTY...........................30

3
March 1
st
, 2015
Introduction
Read all instructions carefully before install your new J. A. ROBY wood stove. A good installation is very important for a safe and effective
use of J. A. ROBY INC stove. In the doubt about the instruction step to install your appliance correctly, we suggest to call a professional
master installer. A wrong installation may result with a fire, burns and possible death.
Keep these instructions.
This appliance must be connect to
•A HT type factory-built chimney approved UL103 or ULC 629 with 6 inches diameter (15.24 cm)
•A code-approved masonry chimney with a flue liner with a 6 inches diameter (15.24cm)
N.B: Be warned that the local’s codes and rules can have more specific requirement than this manual. You can consult a master installer,
fire officials or local building about restriction and installation inspection in your area and to determine if you need to obtain a permit
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE

4
March 1
st
, 2015
Nameplate.

5
March 1
st
, 2015
Appliance Dimensions.
Figure 1

6
March 1
st
, 2015
Installation.
Floor protection.
Your stove must be installed on a non-combustible material plate to protect the floor and avoid fire would be caused by:
•Projections of sparks when door opening or loading logs
•The heat radiation when stove runaway should have an ignition to the floor and the coating.
•Flow of creosote when there is a fire chimney
The coating used must be non-combustible and approved according to standard UL1618 for USA or approved to the locals codes
(Example: cement, brick, ceramic tiles…)
Floor protection plate minimum dimensions.
The following dimensions are the minimums values and it can be higher.
Canada:
•41 7/8 (106 cm)
•47 5/8 (115.88 cm)
•3/8 in thickness (1 cm)
Unites States
•41 7/8 (106.42 cm)
•45 5/8 (115.88 cm)
•3/8 in thickness (1 cm)
It’s necessary to protect the floor behind the horizontal
connecting pipe section to the chimney of 2 inches (5cm)
besides connecting pipe and up to the vertical connecting
pipe. You can extend the protection plate while respecting the
clearances of each side of stove.

7
March 1
st
, 2015
Clearances of the stove until the floor plate protection.
The following dimensions are the minimums values and it can be higher.
Canada:
•8 in (20.3 cm) behind
•8 in (20.3 cm) beside
•18 in (45.7 cm) in front of the door opening.
United States:
•8 in (20.3 cm) behind
•8 in (20.3 cm) beside
•16 in (40.64 cm) in front of the door opening.

8
March 1
st
, 2015
Minimums clearances to the non-combustible material.
With these reduced clearances, this appliance take a minimum of space where is installed. Whether in the living room or the dining
room, the Cook stove will complete your decorate by his originality and heating, it requires a minimum clearance of 12 inches to the
back (for a smoke simple pipe with a heat shield ) and a 18 inches lateral MINIMUM clearance.
•In the case with a smoke simple pipe without heat shield, you must installed the cooker stove that the smoke pipe is
to 18 inches of all non-combustible material therefore the MINMUM clearance at the back of the stove will be 16¼
inches (41.3cm).
•For a 45° corner installation, or other corner installation, the minimum clearance between the cook stove and non-
combustible material must be 18 inches (Figure 3).
Figure 3

9
March 1
st
, 2015
Assembly before installation
According to chosen option, to save more storage space and
shipping. The stove leg and warmer couldn’t be assembled in
the shop, you must assembly before install the cooker stove.
Legs installation.
1) Remove legs and bricks from combustion chamber to
lighten the stove.
2) Unscrew the stove from the skids.
3) Made 2 column of 7 bricks spaced by 14 inches (36.6
cm) Be sure to remove any nuggets under the bricks
4) Put the stove on the bricks like shownon the illustration
and center it on the other direction.
5) Unscrew the nut not completely
6) Install the legs (#1) like the illustration (Attention: Be
sure the legs are in place, correctly positioned and in
contact with the bottom of the stove.)
Warmer stove Assembly (Optional).
Now, you need to know whichtype of smoke pipe: smoke simple
pipe or smoke double pipe.
For the smoke simple pipe: It’s not necessary to remove the pre-
cut metal part.
For the smoke double pipe, you must remove the pre-cut metal
part on the top, inside and in front of the warmer, see pictures
beside.
1) Put the packaging product on the ground and
put the back on it to protect the painted part
Commenté [D1]:
Illustration

10
March 1
st
, 2015
1) Fix the left side.
2) Fix the right side.
3) Fix the front (with the door) with the two sides and the
back. Keep the horizontal holes empty for the chrome
decoration.
4) Insert the chrome decoration in the hole and fix-it with
carriage bolt and nut (2 bolts each).
5) Fix the top with the back and with the front too.
6) Fix the left decorative panel side and finish to install the
left chrome decoration
7) Fix the right decorative panel side and finish to install
the right chrome decoration.