J.Burrows JBMATMECBK User manual

MATRIX MESH DRAFTING CHAIR
ASSEMBLY
INSTRUCTIONS
JBMATMECBK
1/8
1 CTN
www.officeworks.com.au
This design and instruction booklet is subject to copyright.

2/8
Furniture Assembly Instructions S
tyle Guide
Estimated Assembly Time: 30 minutes
Assembly Video
Customer Service Contact Details
Spare Parts & Hardware
1300 OFFICE
People Required
General Advice
To view an assembly video, go to https://www.officeworks.com.au/
Search the product by item code or name:
Click on the icon to watch the video.

3/8
Officeworks Ltd. | 236-262 East Boundary Road | Bentleigh East VIC 3165 | AUSTRALIA
NOTE
•Please check you have all hardware before assembling.
•If you are missing any hardware, please contact the store of purchase.
•Please ensure you have the name of the item, required hardware part and quantity.
•Please retain your receipt as proof of purchase to validate your warranty.
CAUTION
•Do not tighten screws before all screws are in the right place.
•Do not use this product unless all bolts, screws and knobs are firmly secured.
•Check that all bolts and screws are securely tightened at least every 4 m onths.
WARNING
•If parts are missing, broken, damaged or worn stop using the product until all repairs are made
using manufacturer authorised parts.
•
Failure to follow these warnings could result in serious injury.
DANGER
CHILDREN MUST BE SUPERVISED.
••
•

Parts List
Hardware List
4/8
AX5
DX1
GX2 HX1
EX1
IX2
LX2 MX2 NX1
JX4 KX3
FX1
BX1 CX1
1/4”x1-1/2”
5/16”x1-1/4”
5/16”x3/4”
5/16”x1”
1/4”x1-3/4”

Ix2
Jx4
Nx1
Step 1
Step 2
5/8
1/4”x1-1/2”
1/4”x1-3/4”
G-R
G-L
Jx2
N
I
E
C
B
A
IJx2
Assembly

Step 3
Step 4
6/8
N
L
D
M
IMPORTANT: To make assembly easier, do not tighten screws completely at this time.
N
F
K
IMPORTANT: To make assembly easier, do not tighten screws completely at this time.
5/16”x1-1/4”
5/16”x3/4”
5/16”x1”
Kx3
Lx2
Mx2
Nx1
Nx1

H
Now, tighten all screws using allen key-N
Step 3
Step 4
7/8

8/8
Pull lever up whilst moving the
arm up or down. Release lever
at desired height.
Arm Height Adjustment
While seated, reach under the right side of the chair
to find the height adjustment handle.
Pull the handle all the way out (away from the gas lift)
to allow the seat to tilt back or forth. To lock the seat
in the upright or vertical position, sit upright & push
the handle in towards the gas lift.
Seat Tilt
To increase chair height pull
lever upward while lifting body
weight slightly off the seat.
Release lever at desired height.
To lower chair height sit fully into
the chair & pull lever upward.
Chair Height Adjustment
Release lever at desired height.
Your feet should be resting flat on
the floor.
Care Instructions-Fabric Chairs
Clean, check & tighten all parts regularly.
Wipe over surfaces with damp cloth rinsed in warm water & mild detergent.
Dust & vacuum chair fabric to remove dust & dirt.
detelpmocsitsettopsaerusnE.renaelcdesab-retawaesu,tsisrepsniatsynafI
first to ensure it does not affect the fabric colour.
Do not use harsh detergents, solvents or abrasive cleaners.
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products,
please visit www.officeworks.com.au