Jabra Pro 9450 Mono Flex User manual

Jabra Pro 9450 Mono Flex
How to connect my Jabra PRO 9450 with Alcatel IP Touch
4028 EE, 4038 EE, 4068 EE
Prerequisite:
Jabra PRO 9450 + Jabra LINK 14201-20
In combination with one of the following phones:
IP Touch 4028 EE
IP Touch 4038 EE
IP Touch 4068 EE
EE = Extended Edition
Connection:
1. Insert the RJ9 to RJ9 connection cable supplied with the Jabra PRO
94x0 into the socket marked with the "phone" on your Jabra PRO 94x0
base and the other end into the socket marked with a "phone" on the
EHS adapter
2. Now connect the end of the RJ45 to RJ45 connection cable (EHS
adapter) marked in "red" to the socket marked "AUX" on the EHS
adapter to the "AUX" socket on your Jabra PRO 94x0 base.
3. With the cable marked white D, connect the Headset / Handset socket
on your Jabra LINK EHS Adapter to the 3.5 mm headset socket on the
side of your desk phone.
4. Now connect the RJ12 to RJ12 connection cable marked orange and
"A" to the socket of the EHS adapter identified with "COM" as well as
with the "bell" socket on your phone.
Please be aware that the phone will not be fully functional until the
24/11/2022 16:30
https://www.apac.jabra.com/supportpages/jabra-pro-9450/9450-25-707-
103/faq/8df8fc6e-dbbb-43d7-ae3d-d33e7ff4bbf7
Page 1 of 4

coloured markings for all cables have been connected to the EHS adapter.
See photo.
You now have the option of setting up the headset on your phone via the
automatic or manual configuration.
Automatic configuration:
To start the automatic configuration, ask someone to call you on this
phone and wait at least 10 seconds before taking the call. The appropriate
EHS mode should now be installed.
If the automatic configuration has not worked, please select DHSG mode
manually.
Base setup:
Set the phone set-up switch to position "A".
24/11/2022 16:30
https://www.apac.jabra.com/supportpages/jabra-pro-9450/9450-25-707-
103/faq/8df8fc6e-dbbb-43d7-ae3d-d33e7ff4bbf7
Page 2 of 4

Microphone level setup:
Remove the cover from the base of the Jabra PRO 9450 and make a call
with the headset, to a colleague for example. If you are too loud or too
quiet to the person you are calling, please use the volume adjuster until
you achieve the optimum volume level.
Phone setup with system software version 9.xx and higher:
Settings on the phone are no longer required to use the headset. After
correctly adapting the phone plug, a headset symbol should now appear in
the "phone display". Should the headset symbol not appear, please check
the following settings:
Menu > Settings > Phone > Phone plug > Activate/select headset.
Phone setup with system software version below 9.xx:
Important: The "Force Headset" function on the phone must not be
activated as otherwise it will not be possible to receive external calls.
Menu > Settings > Phone > Phone plug > Force headset OFF.
Menu > Settings > Phone > Socket > Activate headset.
Dial tone transfer / phone setup:
Important: The dial tone signal in the headset is only transferred if one of
24/11/2022 16:30
https://www.apac.jabra.com/supportpages/jabra-pro-9450/9450-25-707-
103/faq/8df8fc6e-dbbb-43d7-ae3d-d33e7ff4bbf7
Page 3 of 4

the following ring tones has been selected on your phone Standard /
Classic / Cold River / Dooing-Dooing. > Menu > Settings > Dial tone >
Internal / External
In the event that you still do not have a dial tone signal transfer despite
setting the correct ring tone, check the following settings:
Menu > Settings > Phone > Internal/External > other options
No tone, progressive, bleep tones > all items must be set to "OFF".
24/11/2022 16:30
https://www.apac.jabra.com/supportpages/jabra-pro-9450/9450-25-707-
103/faq/8df8fc6e-dbbb-43d7-ae3d-d33e7ff4bbf7
Page 4 of 4