Jawbone Icon User manual

TALKING POINTS
1
GET
CONNECTED
I N 3 0 S ECONDS
S L I D E O N
L E D
P R E S S + H O L D
TA LK BUT TO N
1 . 1 P R E P AR E YO U R J AW B O N E
Press and hold the T A LK B U T T O N while
sliding O N your Jawbone until the LED
flashes R E D + W H I T E . This indicates
that the Jawbone is ready to connect
(pairing mode).
1 . 2 P R E P AR E YO U R P H O N E
Turn on the Bluetooth® settings.
O N A N I P H O N E ®
Go to SET TINGS > GENE RAL >
and enable B L U E T O OT H ®
O N A B L A C KB E R R Y ®
Go to S E T T I N G S /O P T I O N S >
BLUETOOTH > and enable
B L U E TO O TH ®
O T H E R C E L L P H O N E S
Go to J AW B O N E . C O M / PA I R I N G
or review the instruction manual
that came with your phone
1 . 3 M A K E T H E CO N N E C T I O N
Go to your phone’s Bluetooth® settings.
A D D O R S E A R C H F O R D E V I C E S
When “Jawbone ICON” appears,
select it
IF ASKE D FOR A PASSCODE ,
enter “ 0000”
This is a one-time event you should
not have to repeat, unless you are
connecting your Jawbone headset
to a new phone.
2
GET
COMFORTABLE
2 . 1 F I N D YO U R F I T
Mix and match to select the most
comfortable and secure fit option.
Jawbone can be worn W ITH or
W I T H O U T an earloop.
2 . 2 DR OP, T W I S T & P O I N T
For the most secure fit, place your
Jawbone in your ear pointing down.
Then twist it upwards so it points
directly at your mouth.

2 . 3 E N S U R E B E S T Q U A LI T Y
Jawbone works regardless of position,
but you will get the best performance
if the Voice Activity Sensor physically
touches your cheek.
V O I C E
AC T I V IT Y
S E N S O R 3
TALK
T A L K B U T T O N
3 . 1 TA K E A C A L L
Press the TA L K B U T T O N on your
Jawbone to answer. When you are
finished talking, press the TA L K
B U T T O N to hang up.
3 . 2 M A K E A C A L L
Use your phone to dial as usual. Listen
and talk through your Jawbone. To
hang up, just press the TA L K B U T T O N .
4
POWER UP,
ETC.
L E D
4 . 1 G E T J U I C E D
Your Jawbone is partially charged and
ready for use right out of the box.
W H E N B AT T E R Y LO W
The LED indicator flashes R E D .
FO R A F U L L C H A R G E
Plug it in.
N O T E It takes 40 minutes to get
your Jawbone 80% charged. A full
charge takes 90 minutes.
W H E N F U L LY C H A R G E D
The LED indicator turns W H I T E .
G E T M O R E H E LP ( I F YO U N E E D I T )
V I S I T J AW B O N E . CO M / S U P P O R T
C A L L 1 - 8 7 7 - A L I P H C O ( 2 5 4 - 74 2 6 )
G O T O J AW B O N E . C O M / WA R R A N T Y
for warranty info
P U R C H A S E the official Jawbone
Car Charger and other accessories
at JAW B O N E . C O M
Become a fan of Jawbone
on Facebook®
V I S I T J AW B O N E . C O M / F AC E B O O K
© 2 0 1 0 A L I P H C O M . A L L R I G H T S R E S E R V E D . 7 7 0 - 0 0 1 5 0 R E V H