IASUS Stealth IA-NT4-BASIC-BT User manual

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 1
b l u e to ot h t h r o at m i c h e a d s e t
MODEL NUMBER: IA-NT4-BASIC-BT
Thank You for choosing the IASUS STEALTH Throat Microphone Headset System.
In this manual, you will nd instructions to operate your STEALTH Throat Microphone
Headset with Bluetooth enabled devices. Should you have any questions and require
assistance with setup and usage, please feel free to visit our website,
or contact us directly at : [email protected]
www.iasus-concepts.com

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 2
ABOUT THIS MANUAL
WARNINGS
We recommend reviewing this manual in its entirety before using this product to get the most out of
it, for a richer user experience.
Any changes or modications to this unit not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment,
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause
undesired operation.
SPECIFICATIONS
AVRCP 1.6
A2DP 1.3.1
HFP 1.7
Adjustable & removable neck strap.
Magnetic breakaway clasp.
Flexible silicone wing blade design
for a customized angle t.
PLAYBACK TIME ....................... 9 HOURS
CALL TIME ...................................10 HOURS
STAND-BY TIME ..................250 HOURS
CHARGING TIME ..............90 MINUTES
CHARGING SPECS ................................... 5V
BATTERY CAPACITY ..............1500mAh
HSP 1.2
SPP 1.2
BLE 5.0
Ingress Protection Rating against
dust and water.
Silicone surrounding all essential
ports restricts entry of dust and
dirt.
SUPPORTED PROFILES
STRAP ERGONOMY
BATTERY STANDARD

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 3
MAGNETIC BREAKAWAY CLASP......................................................8
TABLE OF CONTENTS
PARTS & CONTROLS REFERENCE....................................................4
ORIENTATION OF THE STEALTH DURING USAGE.........................5
BACKGROUND NOISE THROUGH
MULTI-MIC MOVILE DEVICES.........................................................5
THROAT MIC OPTIMIZATION ..........................................................5
CHARGING .........................................................................................6
ELASTIC WRAP FOR ACOUSTIC COIL.............................................8
INTERCHANGEABLE MODULES.......................................................7
BLUETOOTH PAIRING.......................................................................9
PRIMARY BUTTON CAPS ..................................................................9
PAIRING A SECOND DEVICE......................................................... 10
CONTROLS ...................................................................................... 11
GETTING STARTED ....................................................................................... 11
MUSIC MODE..............................................................................................12
PHONE MODE..............................................................................................12
VOLUME LEVELS ON MUSIC MODE & PHONE MODE................ 13
LED INDICATOR DEFINITION ....................................................... 13
TROUBLESHOOTING...................................................................... 14

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 4
13
1 2
10 4
11
3
56
12
7
8
9
1.......... + Button
2.......... - Button
3.......... Primary Button
4.......... Primary Button Ring with Regular Cap
5.......... Magnetic Clasp Base
6.......... Magnetic Clasp Top
7.......... Acoustic Coil Module
8.......... 3.5mm (recessed/slim jack) Module
9.......... Speaker 3.5mm slim connector
(sold separately)
10....... Wing
11....... Opaque Cap
12....... Elastic Wrap for Acoustic Coil
13...... Charging Cable
TIP: STEALTH comes charged and ready to use.
PARTS & CONTROLS REFERENCE

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 5
When positioning the Stealth, the volume buttons on the
wing should be facing downwards, while the primary but-
ton should be on the left side of the throat and the acoustic
coil or 3.5mm module attachment should be on right side.
The optimal position for a throat mic is about 1-1.5” to the
side of the voice box where the Stealth is positioned.
The throat mic wing shape was designed for aerodynamic
applications so that there would not be pressure applied
to the neck under high wind situations. Ergonomics are
comfortable and intuitive to use.
NOTE: The transponders should rest comfortably on the neck
and be in contact with your neck at all times. They should
not be too tight. The adjustable straps have ex in order for
to maintain the Stealth in position. Dot not over tighten the
straps.
For users with no prior experience with throat mics, please keep in mind the sound quality will never be
as clear as a standard headset. This is because the audio is created from vibrations of the larynx through
the body of the throat. Since air is not the medium, nasal sounds will be absent.
The audio quality is similar to a person with a cold, hence the “mufed” sound that is commonly
associated with throat mics. The Stealth benets from a vast improvement of sound quality through
our in-house advancement.
IMPORTANT: DO NOT WEAR THE THROAT MIC AND STRAP TOO TIGHT AROUND THE NECK.
When worn properly, the neck strap should rest on the back of the neck and only very little pressure
should be felt
1 to 1.5 in.
ORIENTATION OF THE STEALTH DURING USAGE
THROAT MIC OPTIMIZATION
BACKGROUND NOISE THROUGH MULTI_MIC
MOBILE DEVICES
New smartphones on the market today have secondary mics, which are used in conjunction to the
primary mic input for background noise cancellation.
When using a headset, the device uses the primary mic to compare to secondary mic inputs and
processes accordingly. When the throat mic is not worn, the secondary mic provide slight voice
inputs because no audio is picked up from the throat mic. However, once the throat mic is activated,
the audio will perform back to normal.

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 6
The Stealth comes shipped from our facilities with the built-in Lithium-Ion battery already charged
and ready for use.When charging is needed, connect the included USB cable to the micro-USB port
covered by the Primary Button Ring.
To access the charging port, remove the Primary Button Ring by turning it counter-clockwise.
A full charge takes about 90 minutes to complete and a red LED will remain lit until it is fully charged.
Please note to charge with a computer USB port only.
Fast chargers (>500mA) may damage the Stealth’s charging mechanism. To avoid damage to the battery,
refrain from draining the battery completely and leaving it without charge for an extended amount of
time.
CHARGING 100% CHARGED
CHARGING

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 7
The Stealth can operate with two modules for audio output :
• The accoustic coil module
• The 3.5mm recess/thin audio connector module.
To use the Stealth with helmet speakers or earbuds, please connect the 3.5mm recess/thin audio
connector to the throat mic. Each module can be switched and replaced as follow:
To properly attach either module, it needs to be turned clockwise and tightened rmly until the IASUS
logo is horizontal and right side up. This position ensures proper alignment with the electrical contacts. It
should be tightened to the point where it will not turn anymore in order for the silicon ring to maintain a
waterproof seal.
NOTE: When connecting helmet speakers or earbuds to the iASUS helmet speaker’s 3.5mm jack module, be
sure to insert the plug all the way into the module until a click is felt to conrm a waterproof seal has been estab-
lished.
3 •Turn clockwise to install the
new module and tighten rmly.
1 •Turn counter-clockwise
to unscrew the module
2 •Remove the currently
installed module
INTERCHANGEABLE MODULES

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 8
The neck strap has an elastic loop close to the neck to prevent it ailing around during use. Simply route
the acoustic coil through the loop and adjust the position.
ELASTIC WRAP FOR ACOUSTIC COIL
MAGNETIC BREAKAWAY CLASP
The Stealth neck strap is equipped with a magnetic breakaway clasp, designed for emergency situations
when a rapid removal of the headset is required. This is done by pulling on either strap away from the
other to disengage.
Under normal usage, always separate the top clasp from the base clasp with a twisting motion – left hand
pushing down and right hand twisting up. Only a very light force is required. Disengaging the clasps any
other way during normal every day usage is unnecessary and not recommended.

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 9
Included with the Stealth are two interchangea-
ble Primary Button Caps. The purpose of these
two caps is to alter the visibility of the indicator
LED. The regular cap allows the LED to shine
through while the opaque cap blocks it. You may
wish to swap in the appropriate cap depending
on your use of the Stealth.
To switch caps, turn the Primary Button
Ring counter-clockwise, replace the cap,
and tighten the ring.
REGULAR CAP OPAQUE CAP
PRIMARY BUTTON CAPS
DEVICE 1
Press and Hold Primary Button for at least 3 second until
LED ashes Red and Blue with an audible pairing tone.
Find “STEALTH” in the list of available devices in the
Bluetooth menu of the device you are pairing.
The STEALTH uses standard Bluetooth 5.0 protocols.
When paired with newer devices, there is no need to enter
a passcode. For older Bluetooth equipped devices, enter the
code “0000”
A list of supported protocols can be references in the Speci-
cations section.
TURN PAIRING MODE ON PAIR DEVICE
1 2
BLUETOOTH PAIRING

IASUS_STEALTH_OPERATINGINSTRUCTIONS_v6_2020 10
The IASUS STEALTH allows for pairing with two Bluetooth
enabled devices at the same time (smart phone, GPS, mp3
player, etc.)
To pair a second device, after STEALTH is paired with the
rst device, press and hold the Primary Button for at least 3
seconds to get into pairing mode.
Find “STEALTH” in the list of available devices in the
Bluetooth menu in the device you are pairing.
Pairing the second device will disconnect STEALTH from
the rst device - this is normal. Go to your rst device’s
Bluetooth settings and manually reconnect to STEALTH.
TURN PAIRING MODE ON PAIR SECOND DEVICE
RECONNECT FIRST DEVICE
1 2
3
PAIRING A SECOND DEVICE
DEVICE 2
DEVICE 1