Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES Safety guide

Jabra Link 14201-20
How to connect my Jabra GN9330e with Alcatel IP Touch 4028
EE, 4038 EE, 4068 EE
Prerequisite:
GN Jabra 9330e + Jabra LINK 14201-20
In combination with one of the following phones:
IP Touch 4028 EE
IP Touch 4038 EE
IP Touch 4068 EE
EE = Extended Edition
Connection:
Connect the EHS adapter to the Jabra GN9330e base as follows:
1. Insert the supplied RJ10 to RJ10 connection cable into the socket of
your Jabra GN9330e base marked "phone" and the other end into the
socket of the EHS adapter marked with the “phone” symbol.
2. Now connect the end of the RJ45 to RJ45 connection cable (EHS
adapter) marked in red with the socket of the EHS adapter marked
with "AUX" and the socket of your Jabra GN9330e base marked with
"AUX".
3. Now connect the white RJ10 to the 3.5 mm jack connection cable
marked "D" to the socket of the EHS adapter marked with
"Headset/Handset" and with the headset socket of your phone.
4. Now connect the orange RJ12 to RJ12 connection cable marked with
"A" to the socket of the EHS adapter marked with "COM" and with the
"bell" socket of your phone.
04/11/2022 08:29
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/2188ed47-
9bb4-4f91-bf14-ca96af19c4b8
Page 1 of 4

Please note that full functionality is only available when all the color-
marked parts of the cables are inserted into the EHS adapter, see photo.
Put the headset into the base and activate the “DHSG” mode.
Hold down the “phone” button on the base of the Jabra GN9330e for
approx. 6 seconds until the online display (blue LED) on the headset starts
to flash. The current software is displayed to you by activating the volume
controller in the form of the charge display (green LED).
LEDs from left to right:
LED 1 = RHL
LED 2 = DHSG
LED 3 = AEI
LED 4 = MSH
Thereafter, you can switch into the different software modes (LED 1-4)
with the “volume” controller on the headset. To confirm the software has
successfully installed, the base automatically switches back to charge
mode after approx. 15 seconds.
Base setup:
04/11/2022 08:29
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/2188ed47-
9bb4-4f91-bf14-ca96af19c4b8
Page 2 of 4

Set the phone setup switch (A-G) to "A".
Headset answer/end:
As soon as the dial tone signal can be heard in the headset, you can answer
the call by pressing the ”answer/end” button on the headset; by pressing
again the call is ended.
Phone setup with system software version 9.xx and higher:
No settings are required on the phone for the use of a headset. Following
the correct adaptation of the audio jack, a headset symbol should appear
in the “phone display”. If the headset symbol does not appear, please
check the following settings:
Menu> Settings> Phone> Audio Jack> Select / Activate Headset.
Phone setup with system software below version 9.xx:
Important: The “Force Headset” function must not be activated on the
phone, as otherwise it will not be possible to accept external calls.
04/11/2022 08:29
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/2188ed47-
9bb4-4f91-bf14-ca96af19c4b8
Page 3 of 4

Menu> Settings> Phone> Audio Jack> Force Headset OFF
Menu> Settings> Phone> Socket > Activate Headset
Dial tone transfer / phone setup:
Important: The dial tone signal in the headset is only transmitted if one of
the following ringtones is used, e.g., Standard / Classic / Cold River /
Dooing-Dooing. > Menu> Settings> Dial Tone > Internal / External
Should the dial tone signal transfer not work although you have setup the
correct ringtone, please check the following settings:
Menu > Settings > Phone > Internal/External, More Options
No sound, Progressive, Beeps> all points must be set to "OFF".
04/11/2022 08:29
https://www.apac.jabra.com/supportpages/jabra-link-14201-20/14201-20/faq/2188ed47-
9bb4-4f91-bf14-ca96af19c4b8
Page 4 of 4