Jackedin Power Locker JACK User manual

Locker JACK
Unpacking the Locker JACK
Included:
1 Locker JACK
1 Door Lock Control Key
1 Power Cord
2 90 degree wall mount brackets
4 10-32 x 5/8” screws
Oponally Purchased:
40 Micro USB cords
40 Lighng connector adaptors
Installaon
For safe and proper installaon JackedIn Power recommends installing the Locker JACK as indicated below:
1. Choose a locaon for the Locker JACK that has a 110 V outlet within 6 feet of the power entry module. Remove the
Control Key that is taped to the back of the unit and store in a safe and secure locaon outside of the Locker JACK.
2. Install the two 90 degree wall mount brackets as indicated in picture below (See Figure 1) before mounng the
Locker JACK unit to them. Use three (wall material appropriate) lag bolts (1/4” dia x 2” long) per 90 degree wall
mount bracket (6 lag bolts not included with the unit).
Figure 1

Installaon (cont)
3. Aer installing the two 90 degree brackets to the wall, team li (more than one person) the Locker JACK onto the
previously mounted brackets. Line up the four mounng holes on the boom of the Locker unit with the four bracket
holes and install the four 10-32 x 5/8” screws included with the Locker JACK (see Figure 2).
Figure 2
4. Next, bolt the two mounng tabs located on the top of the Locker JACK. Use one (wall material appropriate) lag
bolts (1/4” dia x 2” long) per mounng tab (see Figure 3) (2 lag bolts not included with the unit).
Figure 3

Installaon (cont)
5. Lastly, install the included power cord and plug the Locker JACK into the available 110V
outlet. Proceed to the next secon with respect to opening the Locker JACK for the rst me.
Unlocking the door for the rst me.
There are two codes that will open your Locker JACK:
 Manager code: “123456” + “ZEPHYR”
 User code: “1234” + “ZEPHYR”
Once you enter the code and press “ZEPHYR” the lock will open and will stay open for 3 seconds. During this
me rotate the knob a quarter turn clock-wise and pull the door open. Aer 3 seconds passes, the lock will re
-engage and the next me the knob is rotated back to the locked posion it will stay locked. Simply repeat the
code if you need to reopen to close the Locker.
To Change Manager Code:
1. Type “123456” and press “ZEPHYR” buon, green light turns on
2. Press and hold “ZEPHYR” buon for 3 seconds, the buzzer will issue a long “beep” and the green light turns
on.
3. When beep ends and green light turns o, input new self-selected 6 digit manager code and press “ZEPHYR”
buon for conrmaon. The lock issues a long audible “beep “and the red and green light will ash twice to
show manager code has changed successfully. Lock is now set new 6 digit Managers code.
a. If an incorrect 6 digit code is entered the red light ashes 3 mes to indicate an error.
To Open with a User Code:
To Open Lock
1. Enter USER code, then press "ZEPHYR" buon, green light on. Rotate the knob to unlock.
2. Aer three seconds, the green light will go o; Lock is in the pre-lock status. Rotate the knob to lock.
If the code is incorrectly entered, the red light ashes 3 mes indicang the wrong code.
To Change user code
1. Input current 4 digit code, press "ZEPHYR" buon, green light on.
2. Press and hold "ZEPHYR" buon for 3 seconds, the lock issues a long audible “beep” and the green light turns
on.
3. When beep ends and green light turns o, input new self-selected 4 digit user code and press "ZEPHYR"
buon for conrmaon. The lock issues a long audible “beep “and the red and green light will ash twice to
show user code has changed successfully. The lock is now set to the new 4 digit code.
If an incorrect 4 digit code is entered the red light ashes 3 mes for the error

Troubleshoong
Forgoen Access Codes:
Reset to factory default
1. If the User Code and Manager Code are forgoen, use the Control Key to open the door.
2. Unscrew the baery cover to get access to the Reset buon.
3. Insert a paper clip or other thin tool into the hole marked “RESET” to depress the buon. The lock will issue 2 audi-
ble "beeps”, the green and red light will ash twice.
a. The lock has now been reset to the factory default sengs of, User Code “1234” and Manager Code
“123456”.
Insucient baery power alarm:
If the baery power is low, the lock will issue an alert with 3 “beeps" when the lock has been opened. Replace Baer-
ies.
Daily use of the Locker JACK
1. Enter the required code (Manager or User Code) to open the Locker JACK
2. Use your chosen USB charging cord and plug the USB end into on of the 40 available USB ports and the other end of
the cable into your phone.
3. Lastly place your phone into the designated phone cube.
4. Close the Locker JACK to secure your phone in the box.
Notes on Use
 If the Control Key is lost and the Manager and User Codes are forgoen, there will be no warranty for these situa-
ons.
 Do not expose the Locker JACK to water.
 To avoid electric shock, do not disassemble the device.
 If trouble occurs, immediately disconnect the charging staon from the wall socket and call Customer Service.
Maintenance
 Keep unit clean and free of debris
 Do not hang or pull on the Locker JACK when mounted or in use.
 USB phone cables are rated for 1,500 inserons. If connecon becomes inconsistent replace USB cables as needed.