Jackson 5050H User manual

JACKSON TOOL • P. O. BOX 5701 • GREENVILLE, SC 29606
877-522-8995 or 864-721-4235 • FAX [phone] • www.jacksontoolinc.com
Model 5050H Pipe Hanger Cart
This manual is free of charge. All personnel who operate this Pipe
Hanger Cart should have a copy of this manual and read and understand
its contents. To request a copy, call or write to the address below.
Read and understand this material before operating
or servicing the Pipe Hanger Cart. Failure to understand
how to safely assemble, operate and service this unit
may result in property damage, serious injury or death.
Assembly, Safety and Parts Manual
06/2019
1
2
3
5
6
7
8
9
4
8" CASTERS
QUICK
LOCK
BRAKE
ADJUSTING
HANDLE
HEAD
STEEL
ROLLERS
1
2
3
4
5
6
HEAD
SHOULDER BOLT
ROLLER
SPACER
SET SCREW
BRONZE WASHER
ITEM QTY DESCRIPTIONPART NUMBER
1
2
3
4
5
6
1 636-856BASE WELDMENT
1 636-855TOP WELDMENT
5
CASTER
1
1 636-5WASHER
5
SET SCREW-5/16-18 X 1/4" LONG
74NUT-HEX, 3/8-16 (NYLON INSERT)
84SCREW-SHOULDER 1/2" X 2-1/4" LONG
94ROLLER 536-752
SPACER 636-846
636-4
2508-8
636-3
636-2
ITEM QTY DESCRIPTIONPART NUMBER
1
2
3
4
5
6
1
1
1
1
1
1
HANDLE NUT
HOLDDOWN WELDMENT
ACME SCREW
LINK-WRENCH CHAIN
LINK-QUICK
CHAIN - 10 ft
636-858
FRONT PICTURE FEATURES
EXPLODED VIEW EXPLODED VIEW
ASSEMBLY INSTRUCTIONS

2
DO NOT exceed the capacity of the Pipe Hanger Cart.
ONLY roll on a firm, flat smooth surface.
ALWAYS load lower arms before the top arms and unload top arms
before the lower arms.
ALWAYS assemble the Pipe Hanger Cart according to the instructions
section, using only parts provided by Current Tools.
IMPORTANT SAFETY INFORMATION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
WARNING
DANGER
CAUTION
SPECIFICATIONS – 5050H PIPE HANGER CART
Weight Capacity 1000 lbs. evenly distributed
Pipe Hanger Size 40 — 6" to 8" hangers
120 — 2" to 4" hangers
ASSEMBLY INSTRUCTIONS
1. From the storage position (see page 4), remove and set aside the two pipe hanger tube
sections. Then, raise one of the upright tubes to the vertical position. Ensure the upper
bolt is resting in the slot at the top of the gusset. All the flat washers should be on the
outside of the gusset. Repeat for the second upright tube. At this point, DO NOT fully
tighten the nuts on the bolts.
GUSSET
SLOT
WASHER
LOWER BOLT
UPRIGHT TUBE
UPPER BOLT
LOCK NUT

3
ASSEMBLY INSTRUCTIONS — CONTINUED
2. Spread both upright tubes apart and insert one end of the lower pipe hanger tube into
one of the lower slots with the hanger rods angled upward (see Figure 3A). Then, insert
the opposite end of the lower pipe hanger tube into the other upright tube’s lower slot.
Ensure the lower pipe hanger tube is fully inserted on both ends (see Figure 3B).
3. Install the upper pipe hanger tube by inserting the notch at both ends of the upper pipe
hanger tube into the top of the upright tubes until fully seated (see Figure 3C). Insert the
two locking retainer pins into the holes at the top of the upright tubes and secure.
LOWER PIPE
HANGER TUBE
LOWER SLOTS
UPRIGHT TUBE
LOWER PIPE HANGER
TUBE FULLY INSERTED
PIPE HANGER
TUBE NOTCH
UPRIGHT TUBE
LOCKING
RETAINER PIN
BASE
GRIP
COMPLETED
ASSEMBLY
UPPER PIPE
HANGER TUBE HANGER ROD
Figure 3A Figure 3B
Figure 3C

4
STORAGE POSITION
NOTE: The lower pipe hanger tube is inserted with the hanger rods angling downward.
EXPLODED VIEW / PARTS LIST
PARTS LIST – 5050H
ITEM# PART# DESCRIPTION QTY
1 5050-3 SCREW – HEX HEAD CAP
GR5 ZINC 1/2-13 × 3) 4
2 458-1 GRIP 4
3 536-5 3/8 LOCK WASHER 16
4 5050-2 .50 ID X 1.37 OD × .11
WASHER 8
5 5050-4 NUT – HEX (1/2-13) THIN
NYLON INSERT 4
6 5050H-001 LOCKING PIN / WIRE
RETAINER 2
7 5050H-101 LOWER PIPE HANGER
TUBE 1
8 5050H-102 UPPER PIPE HANGER
TUBE 1
9 5050H-105 BASE W/MESH 1
10 5050H-113 UPRIGHT TUBE 2
11 5633WC-040 3/8 HEX NUT 16
12 5633WC-041 WASHER – FLAT 3/8 (USS)
ZINC 16
13 5633WC-042 SCREW – HEX HEAD CAP
GR5 ZINC (3/8-16 × 1.25) 16
14 5633WC-046 CASTER – SWIVEL 2
15 5633WC-047 CASTER – FIXED 2
16 5050H-DECAL
SET DECAL SHEET 1