Jacuzzi Riva 6 User manual

Riva 6 / Gallery 6 Ring and Leg Installation Instructions
Models: GA95, GA99, GL25, & GL26
BEFORE YOU BEGIN
• Observe all local plumbing and building codes.
• Carefully inspect the new Ring / Legs for damage.
• Determine which tools and materials are necessary by reading the complete mounting instructions and examining the job you have to
do.
© Jacuzzi Luxury Bath • 14525 Monte Vista Ave • Chino • California • 91710 • www.jacuzzi.com #GV64000 02/09
Freestanding Skirt must be securely fastened to the finished floor
prior to installating decorative components.
INSPECT FOR DAMAGE
• Immediately upon receipt, inspect the Ring / Legs contents before installing. Should inspection reveal any damage or defect in the fin-
ish, do not install on the bath. Damage or defect to the finish claimed after the Ring / Legs are installed is excluded from the warranty.
• Jacuzzi Luxury Bath’s responsibilty for shipping damages ceases upon delivery of the products in good order to the carrier. Refer any
claims for damage to the carrier.
• For definitions of warranty coverage and limitations, refer to the published warranty information packed with the product.
• Jacuzzi Luxury Bath is not responsible for any defects that could have been discovered, repaired, or avoided by following this inspec-
tion and testing procedure.
TOOLS AND MATERIALS: The following tools and materials are required but not supplied. Safety glasses, tape measure, clear
silicon, caulking gun, philips screw driver, and flat head screw driver.


 


















GN77 GALLERY 6/ RIVA 6 RING GN75 GALLERY 6/ RIVA 6 LEGS

© Jacuzzi Luxury Bath • 14525 Monte Vista Ave • Chino • California • 91710 • www.jacuzzi.com
#GV64000 02/09
1.
• Place Ring upside down to identify the dimples as shown
in Fig. 1.
• Locate the Ring and Hanger brackets and place them as
shown in Fig. 2.
• Using a Philips Screw driver, attatch the ring and hanger
bracket to the Ring using the provided philips screws.
2.
• Once all the Ring and hanger brackets have been installed, careful-
ly flip the ring over and install onto the freestanding skirt as shown
in Fig. 4. Continue onto installing your Freestanding Bath Tub.
Ring Installation:





 



Ring Bracket / Ring Hanger Bracket
Fig. 2
Ring Installtion Detail
Fig. 3

























Ring and Leg Bracket Location Detail
Fig. 1
3. FOR ADDITIONAL SAFETY.
• After the Ring and Bath has been installed, Place a
bead of clear silicon between the Ring and Tub rim as
shown in Fig. 4.









Silicon Installation Detail
Fig. 4

© Jacuzzi Luxury Bath • 14525 Monte Vista Ave • Chino • California • 91710 • www.jacuzzi.com
#GV64000 02/09
90 DAY (PARTS ONLY) LIMITED WARRANTY ON OPTIONS AND ACCESSORIES
Our warranty covers options and accessories manufactured for the company but not installed by the factory (e.g., fill spout kits, trim
kits, skirts, pillows, etc.) against defects in material or workmanship. Warranty coverage begins on the date the option or accessory was
originally purchased by the user. Contact our Warranty Department 1-800-288-4002 as to where to send the part to receive a warranty
replacement.



















6. FOR ADDITIONAL SAFETY.
After the Ring /Legs have been installed place a bead of clear silicon
between the Ring and the Tub rim as shown in Fig. 8.
Dual lock and foam placement detail
Fig. 6
Clear Silicon Installation Detail
Fig. 8
Leg Installation Detail
Fig. 7
4.
• Place Ring upside down to identify the dimples as shown in
Fig. 1.
• Locate the Leg brackets and place them as shown in Fig. 5.
• Using a Flat head screwdriver, attatch the leg bracket as shown
in Fig. 5 and fasten to the ring using (2) pan head screws.
Ring & Legs Bracket Detail
Fig. 5
Legs Installation:












5.
• Install the Dual Lock onto the top center of each Leg as shown
in Fig. 6.
• Install the Dual Lock onto each of the Leg Brackets as shown
in Fig. 7.
• Align the Legs to the center of the leg support bracket and
angle the bottom so it touches the freestanding skirt and
rotate forward until the Dual lock locks in place as shown in
Fig. 7.