Jacuzzi SWIMSPA Power Actve J16 User manual

 J16 - Power Acve
 J19 - Power Acve
 J16 - Power Pro
 J19 - Power Pro
JACUZZI SWIMSPA COLLECTION
OWNER’S MANUAL
1005244 Revision A

2
Aenon New Swim Spa Owner!
Congratulaons on the purchase of your new Jacuzzi™ swim spa! The following is a list of au-
tomated funcons performed by your swim spa. These funcons are listed below in an
aempt to suppress any operaonal concerns you may have during the first 24 hours of own-
ership! Also listed below are important maintenance recommendaons you should observe
on a regular basis to protect your new investment.
Maintain Healthy Swim Spa Water
Always maintain your swim spa’s water chemistry within the following parameters:
With CLEARRAY® Without CLEARRAY®
pH 7.4—7.6 7.4—7.6
Free chlorine No less than 1.0 ppm 3.0—4.0 ppm
Free bromine No less than 2.0 ppm 2.0—4.0 ppm
Total Alkalinity 100—150 ppm 100—150 ppm
Calcium Hardness 150—250 ppm 150—250 ppm
IMPORTANT: CLEARRAY® Water Purificaon System is factory installed. If the CLEARRAY® sys-
tem is altered or is not operang efficiently then follow the “without CLEARRAY® water chem-
istry parameters as defined by the Associaon of Pool and Spa Professionals. CLEARRAY® re-
quires an annual bulb replacement to properly sanize your water.
TO DECREASE RISK OF INFECTION OR DISEASE! Always maintain your spa
filter as outlined below to ensure healthy spa water.
Required Filter Maintenance
Your new swim spa is equipped with an advanced water filtraon system that provides unsur-
passed water quality! To ensure maximum water quality at all mes, you should clean the
skimming filter cartridge every 3 months, or as necessary.
Required Water Replacement
You should replace the swim spa’s water every 3 months. The frequency depends on a num-
ber of variables including frequency of use, number of users and aenon paid to water qual-
ity maintenance. You will know it is me for a change when you cannot control sudsing
or you can no longer get the normal feel or sparkle to the water, even though the key water
balance measurements are within the proper parameters.
© Jacuzzi Hot Tubs, Inc. All Rights Reserved

3
Table of Contents
1.0 Important Swim Spa Owner Informaon 5
2.0 WARNINGS 5
3.0 Important Safety Instrucons for all Swim Spa Owners 9
3.1 Important Safety Instrucons 12
4.0 Choosing a Locaon 12
4.1 Outdoor Locaon 13
4.2 Indoor Locaon 14
5.0 General Electrical Safety Instrucons 15
6.0 Electrical Installaon Instrucons (230 / 240 Volt Service) 15
7.0 Power Requirements 18
8.0 Swim Spa Fill Up Procedure 18
9.0 Spa Features 24
9.1 J16/19 Power Acve Swim Spa Features 24
9.2 J16/19 Power Pro Swim Spa Features 25
10.0 Swim Spa Operaon 26
10.1 Main Screen 26
10.2 Navigaon 28
10.3 The Spa Screen 28
10.4 The Sengs Screen 31
10.5 Spa Behaviour 35
10.6 Time of Day 36
10.7 Adjusng Filtraon 37
10.8 Light Cycle Opon 38
10.9 Restricng Operaon 39

4
11.0 Pro X Current Control 40
11.1 Manual Workout Mode 40
11.2 Timed Workout Mode 40
11.3 Workout Program Mode 41
12.0 Swim Spa Maintenance 42
12.1 Cleaning the Filter Cartridges 42
12.2 Draining and Refilling 43
12.3 Cleaning the Swim Spa Interior 44
12.4 Pillow Care 44
12.5 Maintaining the Synthec Cabinet 45
12.6 Cleaning the Control Panel 45
12.7 Cover Care and Maintenance 45
12.8 Winterizing 46
12.9 Starng Your Swim Spa in Cold Weather 47
13.0 Water Quality Maintenance 47
13.1 pH Control 48
13.2 Sanizing 48
13.3 Other Addives 49
13.4 CLEARRAY® (Ultraviolet) Water Purificaon System 49
14.0 Error / Display Messages 49
15.0 Troubleshoong Procedures 52
16.0 Typical Swim Spa Wiring Diagrams 54
17.0 Circuit Board Wiring Diagrams 56

5
1.0 Important Spa Owner Informaon
Your Jacuzzi® Swim Spa is constructed to the highest standards and is capable of providing
many years of trouble-free use. However, because heat retenve materials are ulized to in-
sulate the swim spa for efficient operaon, an uncovered swim spa surface and wall fings
directly exposed to sunlight and high temperatures for an extended period are subject to per-
manent damage or discoloraon. Damage caused by exposing the swim spa to this abuse is
not covered under warranty. We recommend that you always keep the swim spa full of water
when it is exposed to direct sunlight and that you keep the Jacuzzi® insulang cover in place
at all mes when the swim spa is not in use. Read and carefully follow the requirements for
your swim spa’s support base found in Secon 4.0 tled, “Choosing a Locaon”.
Jacuzzi® swim spas constantly strives to offer the finest swim spas available, therefore,
modificaons and enhancements may be made which affect the specificaons, illustraons
and/or instrucons contained herein.
2.0 WARNINGS
Jacuzzi Europe S.p.A. declines all liability for damages arising from failure to observe the
following direcons.
For periodic filling, if you decide to connect the swim spa hydraulic circuit to the public
water system that supplies drinking water, this connecon must be carried out in com
pliance with the EN1717 norm, using “AA”, “AB” or “AD” an-polluon protecon proce
dures. For further informaon, we recommend you contact your water supply company
and/or your plumber.
Do not connect the swim spa to the hydraulic system using hoses used to water the gar
den.
CAUTION: Before preparing the drainage system for connecng the swim spa, consult
the local authories about regulaons for the disposal of chemically-treated water.
In areas where winter temperatures frequently drop below 0oC, during the period when the
swim spa is not in use, it is recommended to completely empty the system (swim spa, com-
pensaon tanks, pipes, filter.
In areas where temperatures drop below 0oC only occasionally, the swim spa can be kept in
operaon as it includes a “freeze protecon” feature that guarantees the maintenance of a
minimum water temperature.

6
In case of long periods of inacvity, it is advisable to fully drain the system. Periodic drainage,
during normal use, varies depending on the frequency of use, the contaminants and the type
of installaon. Even if not used parcularly frequently, you should change the water at least
once a month.
Prolonged sun exposure could damage the material of which the swim spa shell is made,
due to its capacity to absorb heat (dark colours in parcular). Do not leave the swim spa
exposed to the sun without adequate protecon when not in use (thermal cover, gaze
bo, etc.). Any damage resulng from failure to observe these warnings are not covered
by the product warranty.
Live components and equipment (except those powered at very low voltage not exceed-
ing 12V) must be out of reach of individuals in the swim spa.
Jacuzzi® swim spas are class “1” appliances and must therefore be permanently connected,
without intermediate juncons, to the electrical network and to the protecon circuit
(grounding system).
Parts containing electrical components, with the excepon of remote control devices,
must be posioned or fixed so that they cannot fall into the swim spa.
The appliance must be powered by means of a differenal switch with operang current
which does not exceed 30mA.
The installer must use cables with a suitable cross-secon with minimum characteriscs
equivalent to type H 05 VV-F. Please refer to the corresponding secon.
For the equipotenal connecon of the appliance the installer must use the terminal provid-
ed and idenfied by the ground symbol. Please refer to the corresponding secon. It is imper-
ave to build a support base adequate to the load of the swim spa.
It is imperave to provide a drainage system for accidental water spills. Please refer to the
corresponding secon.

7
For connecon to the supply network, we recommend installing an isolang mul-pole
switch, which will ensure complete disconnecon in the event of a category III over-voltage;
these devices must be placed in an area that complies with the safety regulaons.
CAUTION! Before carrying out any maintenance operaons, disconnect the appliance
from the power supply line.
CAUTION: (IEC 60335-1) The pressure of the hydraulic system that supplies the equip-
ment must not exceed 600 kPa (6 bar) and, in case water is supplied through solenoid
valve(s) (eg. Balance tank) the pressure must have a minimum value of 35 kPa (0.35
bar).
This equipment may be used by children above the age of 8 or individuals with reduced mo-
bility, sensory and/or cognive abilies only if supervised and only if they have the knowledge
necessary to use the equipment safely, as well as to understand the dangers arising from im-
proper use.
Children must be supervised to make sure they do not play with the equipment and donot
carry out operaons to be performed by adults and/or specialized personnel (maintenance,
cleaning operaons, etc.).
Do not use water with temperatures exceeding 40oC.
Tolerance to hot water varies from person to person. Pregnant women and small children
must not use the swim spa without first consulng a doctor and, in any case, the water tem-
perature must be less than 38oC.
Be very careful when using the swim spa alone. Prolonged immersion in warm water may
cause nausea, dizziness and fainng. If you intend to use the swim spa for more than 10-15
minutes, a lower water temperature must be set. This also applies to children.

8
CAUTION: Do not sit, walk or lie on the cover. Do not place objects on it.
CAUTION: Only “load bearing” covers are designed to support weights (MAX 200 kg),
but they should not be subjected to sudden and strong forces (jumps, etc.). Do not sit,
walk or lie down on other types of covers (non-load bearing); do not store objects on
top of the cover.
In order to avoid accidental falls in the swim spa, we recommend that the locking system sup-
plied with the insulang cover is installed.
Persons with heart condions, diabetes, high or low blood pressure or health problems must
not use the swim spa without first consulng their doctor.
People with infecous diseases should not use the swim spa without first consulng their doc-
tor.
Do not use the swim spa aer drinking alcohol, taking drugs or medicaon that cause drowsi-
ness or that can raise/lower the blood pressure.
Do not use the swim spa in extreme weather condions (during storms etc.).
Persons under medical care must consult a doctor before using the swim spa, as some medi-
caons can cause drowsiness, affect heartbeat, blood pressure and circulaon.
Be very careful when geng in and out of the swim spa. All surfaces are slippery when wet.
When using the swim spa, do not use objects that can breakor that are fragile.
When using the swim spa, you must keep your head, body and clothes at a distance of at least
40 cm from the sucon intakes; long hair must be ed back and secured in place. Do not use
electrical appliances (radios, hair dryers) near the swim spa if it is not empty.
Do not remove the protecve grilles from the sucon intakes. Do not turn on the swim spa if
the protecve grilles are broken or missing; in this case, contact an authorized Jacuzzi® dealer
or an authorized Service Centre for replacement.

9
SUCTION COVERS MUST BE REPLACED EVERY 5 YEARS.
Prolonged sun exposure could damage the material of which the swim spa shell is
made, due to its capacity to absorb heat (dark colours in parcular) . Do not leave the
swim spa exposed to the sun without adequate protecon when not in use (thermal
cover, gazebo, etc.). Any damage resulng from failure to observe these warnings are
not covered by the product warranty.
For all operaons and maintenance of the swim spa, please refer to this manual and, where
indicated, contact an authorized Jacuzzi® service centre.
Please refer to the Jacuzzi system water treatment guide and the relave catalogue for details
on water quality maintenance, the relave methods and instrucons of use of chemical prod-
ucts. Where indicated, contact an authorized Jacuzzi9r) service centre.
3.0 Important Safety Instrucons for all Swim Spa Owners.
READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY!
This swim spa was manufactured to meet the standards and specificaons outlined in the
“Virginia Graeme Baker Pool and Spa Safety Act” (VGB Safety Act). When installing and using
this swim spa, basic safety precauons should always be followed, including:
DANGER: RISK OF SEVERE INJURY OR DROWNING!
 Use the straps and clip e downs to secure the swim spa cover when not in use. This will
help discourage unsupervised children from entering the swim spa. Keep the cover se-
cure in high wind condions.
 There is no representaon that the cover, clip e downs, or actual locks will prevent ac-
cess to the swim spa.
 Never operate or use the spa if the filter, filter lid, or skimmer assembly are broken or
any part of the skimmer assembly is missing. Please contact your dealer or nearest ser-
vice center for service.
 Never replace a sucon fing or sucon cover with one rated less than the flow rate
marked on the original sucon fing. Using improper sucon fings or sucon covers
can create a body or hair sucon entrapment hazard that may lead to drowning or se-
vere injury.

10
DANGER: RISK OF SEVERE INJURY FROM ELECTRIC SHOCK OR DEATH FROM
ELECTROCUTION!
 Never operate any electrical appliance from inside the swim spa or when you are wet.
WARNING: RISK OF SEVERE INJURY OR DEATH!
 Extreme cauon must be exercised to prevent diving or jumping into the swim spa or
slipping and falling, whichcould result in unconsciousness, drowning, or serious injury.
Remember that wet surfaces can be very slippery.
 Never stand, walk or sit on the top railing of the swim spa. Always test the swim spa wa-
ter temperature before entering the swim spa. The user should measure the water tem-
perature with an accurate thermometer since the tolerance of water temperature-
regulang devices may vary as much as +/- 5oF (2oC).
 If you experience breathing difficules in associaon with using or operang your swim
spa, disconnue use and consult your physician.
 Never use a swim spa immediately following strenuous exercise. Enter and exit the swim
spa slowly. Wet surfaces can be slippery.
 To reduce the risk of contracng a waterborne illness (e.g. an infecon, bacteria or virus)
and/or respiratory ailments, maintain water chemistry within the parameters listed on
the inside cover of this manual and consult with a licensed engineer regarding proper
venlaon if installed indoors or in an enclosed area.
 Always shower before and aer using your swim spa. Maintain water chemistry in ac-
cordance with manufacturer’s instrucons. Failure to do so may result in contracng a
waterborne illness (e.g. an infecon, bacteria or virus)
WARNING: In addion to maintenance of filters and water chemistry, proper
venlaon is recommended to reduce the risk of contracng a waterborne illness (e.g. an in-
fecon, bacteria or virus) and/or respiratory ailments that could be present in the air or water.
Consult a licensed architect or building contractor to determine your specific needs if in-
stalling your swim spa indoors.
 Maintain water chemistry in accordance with manufacturer’s instrucons.
 Proper chemical maintenance of swim spa water is necessary to maintain safe water and
prevent possible damage to swim spa components.

11
NOTE: This swim spa is not intended nor designed to be used in commercial or public ap-
plicaons. The buyer shall determine whether there are any code restricons on the use or
installaon of this swim spa since local code requirements vary from one locality to another.
Note: Sucon covers must be replaced every 5 years.
A Warning Sign is provided in your warranty packet. Please install at a locaon near your
swim spa, where it is visible to users of the swim spa. For addional or replacement Warning

12
3.1 Important Safety Instrucons
When using this electrical equipment, basic safety precauons should always be followed, in-
cluding the following:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. A green colored terminal or a terminal marked G, Gr, Ground, Grounding or the
symbol is located inside the supply terminal box or compartment. To reduce the risk of
electric shock, this terminal must be connected to the grounding means provided in the
electric supply service panel with a connuous copper wire equivalent in size to the cir-
cuit conductors that supply this equipment.
3. At least two lugs marked “Bonding Lugs” are provided on the external surface or on the
inside of the supply terminal box/compartment. For the equipotential connection as re-
quired by specific national standards, the installer must use the above terminals
(standard EN 60335.2.60). In particular, an equipotential condition must be established
for all metallic masses surrounding the spa, for example water and gas pipes, metallic
platforms, and so on.
4. SAVE THESE INSTRUCTIONS.
4.0 Choosing a Locaon
IMPORTANT: Because of the combined weightof the swim spa, water and users, it is ex-
tremely important that the base upon which the swim spa rests be smooth, flat, level and ca-
pable of uniformly supporng 1220 kg/m2, without shiing or seling, for the enre me the
swim spa is in place. If the swim spa is placed on a surface, which does not meet these re-
quirements, damage to the skirt and/or the swim spa shell may result. Damage caused by im-
proper support is not covered under warranty. It is the responsibility of the swim spa owner
to ensure the integrity of the support at all mes. We recommend a poured, reinforced con-
crete slab witha minimum thickness of 4 inches (10cm). Wood decking is also acceptable pro-
vided it is constructed so that I meets the requirements outlined above.
WARNING: For swim spas that are to rest on roofs or other plaorms not specifi-
cally ed into main structural supports, consult a professional Structural Engineer
with experience in this type of applicaon.

13
The swim spa must be installed in such a manner as to provide drainage away from it. Placing
the swim spa in a depression without provisions for proper drainage could allow rain, over-
flow and other casual water to flood the equipment and create a wet locaon in which it
would sit in. For swim spas which will be recessed into a floor or deck, install so as to permit
access to the equipment, either from above or below, for servicing. Make certain that there
are no obstrucons, which would prevent removal of all cabinet side panels and access to the
jet components, especially on the side with the equipment bay.
CAUTION: If the swim spa is indoors or located in an enclosed area, proper venla-
on should be discussed with an Engineer or authority competent enough to under-
stand the necessary provisions needed to ventmoistor heated air associated with chemical
odors outdoors. When the swim spa is in use considerable amounts of moisture will escape
potenally causing mold and mildew. This can cause health risk. Over me, this can damage
certain surfaces, surroundings and equipment.
4.1 Outdoor Locaon
In selecng the ideal outdoor locaon for your swim spa, we suggest that you take into con-
sideraon:
 The proximity to changing area and shelter (especially in colder weather).
 The pathway to and from your swim spa (this should be free of debris so that dirt and
leaves are not easily tracked into the swim spa).
 The closeness to trees and shrubbery (remember that leaves and birds could create extra
work in keeping the swim spa clean).
 A sheltered environment (less wind and weather exposure can result in lowered opera-
on and maintenance costs).
 The overall enhancement of your environment. It is preferable not to place the swim spa
under an unguered roof overhang since run-off water will shorten the life expectancy
of the swim spa cover.
 For swim spas that are to rest on roofs or other plaorms not specifically ed into main
structural support, consult a professional Structural Engineer with experience in this type
of applicaon.
 In the unlikely event that you should ever need to access or gain entry to any poron of
the swim spa for servicing, it is highly recommended that you plan your outdoor installa-
on to provide full access to the enre swim spa. Please take this into consideraon
when placing the swim spa in a deck or enclosed by a surrounding.

14
 Consider locang your swim spa away from any reflecve surface or glass to prevent any
damage to the synthec skirt.
 When possible, do not shim the swim spa. To ensure proper support the swim spa must
sit flat on the intended foundaon.
4.2 Indoor Locaon
For indoor installaons many factors need to be considered before installing a spa indoors.
WARNING: In addion to maintenance of filters and water chemistry, proper ven-
laon is recommended to reduce the risk of contracng waterborne illness (e.g. an
infecon, bacteria or virus) and/or respiratory ailments that could be present in the
air or water. Consult a licensed architect or building contractor to determine your specific
needs if installing your swim spa indoors.
 Proper Foundaon: Consult a Structural Engineer when considering a foundaon that
will adequately support the swim spa the enre me it is in place. Proper support is
crical especially if the spa is to rest on a second story or higher. For swim spas that are
to rest on roofs or other plaorms not specifically ed into the main structural support,
you should consult a professional Structural Engineer with experience in this type of ap-
plicaon.
 Proper Drainage: It is extremely important to have in place measures to sufficiently
handle excessive water spillage. Be sure the flooring in which the swim spa rests on has
adequate drainage and can handle the enre contents of the swim spa. Be sure to make
provisions for ceilings and other structures that may be below the swim spas installaon.
Areas around your swim spa can become wet or moist so all flooring and subsequent fur-
niture, walls and adjacent structures should be able to withstand or resist water and
moisture.
 Proper Venlaon: Proper venlaon should be discussed with an Engineer or authori-
ty competent enough to understand the necessary provisions needed to vent moist or
heated air and air associated with chemical odors outdoors. When the swim spa is in
use considerable amounts of moisture will escape, potenally causing mold and mildew
over me, which can damage certain surfaces and/or surroundings.
 Sufficient Access: In the likely event that youshould ever need to access or gain entry to
any poron of the swim spa for servicing, it is highly recommended that you plan your
indoor installaon to provide full access to the enre swim spa.

15
 Warranty: Damage caused by not following these guidelines or any improper installaon
not in accordance to local codes or authories is not covered under the swim spas war-
ranty. Please consult your local state or city building ordinances.
 When possible, do not shim the swim spa. To ensure proper support the swim spa must
sit flat on the intended foundaon.
5.0 General Electrical Safety Instrucons
Your new Jacuzzi® swim spa is equipped with the ProTouch™ system. It contains
the most advanced safety and self-protecve equipment in the industry. None-
theless, this swim spa must be installed properly to ensure dependable usage. Please contact
your local Jacuzzi dealer or local building department should you have any quesons regard-
ing your installaon.
6.0 Electrical Installaon Instrucons (230V / 240V Service)
IMPORTANT NOTICE: The electrical wiring of this swim spa must meet the re-
quirements of any applicable local codes. The circuit must be installed by a quali-
fied electrician and approved by a local building/electrical inspecon authority.
It is the responsibility of the installer to select materials based on their intended use, to carry
out work properly, to check the condion of the system that the unit will be connected to and
that it ensures safetyof use also concerning maintenance work and the possibility to examine
the system.

16
1. The Jacuzzi® spas are class "1" appliances and therefore they must be permanently con-
nected, without any intermediate connecons, to the electrical system and to the pro-
tecon system (earth system)."
2. The power supplied to this swim spa must be a dedicated circuit with no other applianc-
es or lights sharing the power provided by the circuit.
3. The installer must use cables with a suitable cross-secon, with minimum characteriscs
equivalent to type H 05 VV-F.
4. For connecon to the power supply network, we recommend installing an isolang mul
-pole switch, which will ensure-sure complete disconnecon in the event of a category III
over-voltage; these devices must be posioned in an area that com-plies with the safety
regulaons.
5. The electrical system of the building must be provided with a 0.03A differenal switch
and with an efficient protecon (earth) circuit. Check for proper operaon of the differ-
enal switch by pressing the TEST buon, which should trip.
6. The electrical circuit supplied for the swim spa must include a suitable ground fault cir-
cuit interrupter (GFCI) as required by NEC Arcle 680-42/USA.
7. To gain access to the swim spa’s power terminal block, pull the boom of the door panel
to break the magnec lock of the door to the frame. Place the door panel in a safe loca-
on to prevent damage.
8. Select the power supply entrance you want to use, Figure A. Make sure to install a 3/4”
electrical fing and conduit through the large opening provided in the side of the con-
trol box so you can feed the cable through to the terminal block.
9. Connect wires to the terminal block (Figures B-C). ALL WIRES MUST BE SECURELY CON-
NECTED or equipment damage could result!
10. Install the door panel back into place.

17
FIGURE 1
EQUIPMENT AREA
1. Master
2. Auxiliary heater
3. Pump 1
4. Pump 2
5. Pump 3
6. Pump 4
7. CLEARRAY® Water Purificaon System
8. Power Supply Entrance
Note: Equipment locaon and quanty (such as pumps, CLEARRAY ® system, heater etc.)
varies by model.

18
7.0 Power Requirements
Jacuzzi® swim spas are designed to provide opmum performance and flexibility of use when
connected to their maximum electrical service. They are configured at the factory. The most
common electrical connecons are listed below.
EUROPEAN
MODELS (50 Hz)
VOLTAGE 230VAC
MAX CURRENT DRAW
Power Acve Series 28
Power Pro Series 28
Frequency (Hz) 50
Number of wires 3
NORTH AMERICAN
MODELS (60 Hz)
240VAC
40
48
60
4
8.0 Swim Spa Fill Up Procedure
For best results, read each step in its enrety before proceeding with this procedure. Make
sure that all drains and drain plugs areclosed.
1. Prepare the Swim Spa for Filling
 Clear all debris from the swim spa (Although the swim spa shell has been polished
at the factory, you may want to treat it with a specially formulated spa cleaner.)
Consult your authorized Jacuzzi dealer for addional informaon prior to filling.
 Remove both filters, skimmer, polishing filter lids and filters.
2. Fill Swim Spa
 Place the end of your garden hose into empty skimming filter fing as you stand
next to the swim spa. Fill swim spa half way, then place the garden hose into the op-
posite filter fing while adding the remaining fill water.
CAUTION: TO DECREASE BUILD UP ON COMPONENTS AND MINIMIZE ACRYLIC DAMAGE.
Never fill with water from a water soener. If your water is extremely “hard”, it is
preferable to fill half-way with hard water and the rest of the way with soened wa-
ter. Water that is too so can be corrosive to metal components.

19
WARNING: TO DECREASE RISK OF INFECTION AND DISEASE.
Fill the swim spa with clean tap water from garden hose, to reduce the risk of con-
tracng a waterborne illness (e.g. an infecon, bacteria or virus) and/or respiratory ailments.
Fill unl water covers all the jets but does not touch the boom of the lowest headrest (DO
NOT OVERFILL!).
IMPORTANT: Always fill your swim spa through both filter fings aer draining. Failure to
do so may cause air to be trapped in the pumps, prevenng the pumps from circulang water.
Remove the hose and replace both filter cartridges as illustrated in Secon 13.1.
3. Turn On Power
Turn on the power to the swim spa at the home’s circuit breaker. The heater and filter/
circulaon pump will automacally acvate. Normally, at the inial fill, the water tends
to be cold.
4. Acvate Jet Pumps
Turn on jet pumps when adding chemicals in step 5 (see secon 11.2)
5. Add Start-Up Chemicals
Add the swim spa water chemicals as recommended by your authorized Jacuzzi swim
spa dealer. See secon tled “Water Quality Maintenance” for general guidance.
WARNING: RISK OF POISONING OR DEATH.
Never leave chemicals opened and accessible to anyone. Use chemicals according to
the vendor’s instrucons. Always store chemicals in a safe and/or locked locaon. Keep away
from and out of reach of children.
6. Establish A Stable Sanizer Reading
Establish a stable sanizer reading of no less than 2.0 ppm free bromine or no less than
1.0 ppm free chlorine. To ensure healthy water condions, always maintain a constant
sanizer reading within the levels recommended on the inside cover of this manual. If
sanizer levels cannot be stabilized, perform the decontaminaon procedure steps 9-15
on the following pages.
Note: The “Decontaminaon Procedure” should also be used aer the swim spa has been
“Winterized” (Secon 13.8) or has been sing without power for an extended period.

20
7. Set Swim Spa To Heat
To warm swim spa water to a comfortable temperature, follow these steps:
 The display on the control panel displays the actual temperatureof the swim spa
water. Tap the “+” or “-” to increase or decrease the water temperature in 1 degree
increments.
 The heater will turn off 1oF (0.5oC) above the set temperatureand turn on 2oF (1oC)
below set temperature.
Note: The temperature range for the swim spa is 80 to 104oF (27 to 40oC). To acvate the Ex-
tended Temperature feature that allows the swim spa to reach 106oF (41oC) refer to Secon
15 “Error/Display Messages”.
Important Heater Details:
 The maximum temperature for which the swim spa can be set is 104oF (40oC) and the
minimum is 80oF (27oC).
 Seng the thermostat at maximum will not accelerate the heang process. This will only
result in a higher ulmate temperature.
 The heater operates unl the water reaches 1 degree above the programmed “set tem-
perature”, then turns off. The heater will reacvate aer the water cools to approximate-
ly 2oF (1oC) below the “set temperature”.
8. Place Cover On Swim Spa
 Keeping the insulang cover in place anyme the swim spa is not in use will reduce
the me required for heang, thereby minimizing operang costs.
 The me required for inial heat-up will vary depending on the starng tempera-
ture.
DANGER: RISK OF PERSONAL INJURY.
Check water temperature carefully before entering swim spa! Excessive water temperature
can cause burns, welts and body temperature to rise, hyperthermia (over-heang).