Jacuzzi SHER80 Programming manual

Congratulations! You have purchased one of the most
user-friendly pool filters available. Ideal for most pools,
this element filter will provide you with many years of
pool enjoyment.
This step-by-step installation and maintenance guide
will provide the necessary information for you to install
your new filter and easily maintain the equipment.
221666071530B
Owner's Manual and Installation Guide
Element Filter
10/05
Before Installation be sure to read all instructions and warn-
ings carefully. Refer to product dataplate(s) for additional operat-
ing instruction and specifications.
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this equipment, basic safety precau-
tions should always be followed, including the following:
INSPECTION
Examine the equipment when received. Notify your dealer or car-
rier of any damage or missing parts. Verify that equipment is of
size and model specified.
INSTALLATION LOCATION
Locate unit on a solid foundation as close to pool/spa as pos-
sible, but keep at a distance of at least 5 feet (1.5 m). (See above
Warning). Give consideration to drainage - away from equipment,
ventilation, and access for future servicing and winterizing.
PUMP SELECTION
A full line of pool/spa pumps are available for installation with these
filters. For those installations where the equipment will be placed
above the water level, a self-priming pump should be selected. Ask
your dealer to determine the proper size pump for your applica-
tion. Consideration must be given to pipe size and distance from
pool or spa and friction losses of associated equipment.
GENERAL PLUMBING
FOR SOLVENT WELD CONNECTIONS
Rigid or flexible PVC pipe can be used. Pipe ends should be
clean and free of any flask caused by the cutting operation. Be
sure that the proper adhesive is used on the type of pipe speci-
fied.
Caution: We recommend that you consider climatic conditions
when applying adhesives. Certain atmospheric situations, such
as high moisture content, make the adhesive action of certain
glues less effective. Check the manufacturer's instructions.
FOR THREADED CONNECTIONS
Use only Teflon tape or equivalent on threaded plumbing connec-
tions. Other pipe compounds may damage threads. We do not
recommend the use of silicone or petroleum based compounds.
DO NOT OVER-TIGHTEN: HAND TIGHTEN PLUS 1/2 TURN IS
SUFFICIENT.
FILTER PLUMBING
Your filter is provided with 1-1/2" NPT or 2" NPT threaded inlet and
outlet. When installing, look for the words PUMP and RETURN
molded into the filter body.
When the filter is located below water level, a valve should be
installed at both PUMP and RETURN. Shutting off both of these
valves will prevent loss of water during regular maintenance.
To reduce risk of injury, do not
permit children to use this product
unless they are closely supervised at all times.
Locate the system at least five feet
(1.5M) from the pool to prevent it be-
ing used as a means of access to the pool by young children.
(See ANSI/NSPI-8 1996 “Model Barrier Code For Residential
Swimming Pools, Spas and Hot Tubs”).
WARNING
!
WARNING
!
This filter operates under pressure.
If this unit is not assembled properly
or is operated with air in the circulation system, serious bodily
injury and/or property damage could occur.
Your filter is a pressure vessel and
should never be serviced while un-
der pressure. Always shut off pump to relieve the pressure in
the filter and open air bleed prior to servicing the unit.
Always make sure the filter Ring-Lok
is tightened to "built-in stop" prior to
operating pump. Do Not remove or adjust the ring-lok while
the pump is running; doing so may cause the filter cover to
blow off, causing injury or property damage.
WARNING
!
WARNING
!
WARNING
!

2
FILTER START-UP
1. If pressure gauge is not factory installed, thread the provided
gauge (which is wrapped with Teflon tape) into the filter cover.
2. Check to be sure assembly nut on filter is tight, lock tabs en-
gaged and drain valve closed. Open air relief.
3. Perform pump start-up.
4. Close vent when droplets first appear. An excessive spray of
water may occur if venting is not done slowly.
WINTERIZING
Consult your dealer for advice on winterizing your equipment if
freezing temperatures occur in your locality. His knowledge of your
equipment makes him the best qualified source of information.
Follow his recommendations, and if these include draining the
filter, proceed as follows: 1. Clean the filter element and store in
dry area. 2. Drain system by removing drain plug.
WATER CHEMISTRY
A proper and consistent use of chemicals is necessary to main-
tain clean, sanitary water, prevent a spread of germ infection and
control the growth of algae which can spoil the appearance and
enjoyment of your pool or spa. Chlorine is the most commonly
used chemical to provide clean, sanitary water. Either dry or liquid
chlorine (calcium or sodium hypochlorite) can be used which
should be added daily as it is dissipated by dirt and germs as well
as by the sun and the wind. It is also important that the correct level
of acidity or alkalinity of the pool water be maintained. This is the
pH of your pool with pH 7.0 being neutral. Readings above pH 7.0
are alkaline and readings below are acid. A desirable range is 7.2
to 7.4. Consult your local pool/spa dealer for complete information
on proper application and use of chemicals.
FILTER MAINTENANCE
Filter tank and contents should not require attention other than
cleaning filter element, provided water is kept in continuous chemi-
cal balance without heavy dosages of corrosive chemicals.
Note: The element support assembly on the SherLok automati-
cally purges any accumulated air to maintain the internal water
level up to the top of the element. We, however, recommend peri-
odic manual opening of the vent plug to purge any small amounts
of air accumulated under the cover.
REMOVING AND CLEANING FILTER ELEMENT
When the new filter is first placed into service, note the reading on the
pressure gauge. As dirt builds up in the filter, the pressure reading will
increase. When it reads 6 - 8 psi above the original reading, the filter
element should be cleaned as described below or replaced.
Filter Element Cleaning:
1. STOP pump.
2. Close inlet and outlet valves if installed (for units below water
level).
3. Loosen the yellow air vent on the top of the filter.
4. Remove the Ring-Lok. Push in the top of the yellow locking tab
as you begin to rotate the Ring-Lok to allow removal.
5. Using the Lid Removal System tabs on the bottom side of the
nut, remove the cover by inserting the tabs between the cover and
the body and rotating the nut allowing the tabs to pry the cover
upward.
6. Grasp the filter element by the handle and remove it from the
support pipe.
7. The element can usually be cleaned with a high pressure nozzle
on a garden hose. Place the nozzle inside the element and spray
outward pushing any trapped debris from the element.
TIP: For optimum cleaning, allow your element to dry. Brush off the
remaining dirt and chemicals that will not wash off with the hose.
An additional element will allow you uninterrupted enjoyment of
your pool during this cleaning procedure.
INSTALLING FILTER ELEMENT
1. Remove and clean the O-ring on the filter body and lubricate
with petroleum jelly. Also, clean the O-ring groove on the filter body
and the sealing surface inside the filter cover to ensure a leak-free
seal. Install the O-ring on the filter body.
2. Clean the dirt catcher at the bottom of the support tube. This
assembly can be removed if desired by lifting upward on the sup-
port tube while rocking it from side to side. Once clean, replace it
by firmly pushing it back into the filter body.
3. Slide the clean filter element back onto the support tube and
press it firmly into place.
4. Place the cover on the filter body and press firmly downward
until it seats. TIP: It is easier to replace the cover if the air bleed
valve is open.
5. Clean the threads of the Ring-Lok nut and the threads on the
filter body with water or a clean rag. Place the Ring-Lok nut on the
filter and tighten to the built-in stops on the threads. Be sure the
yellow locking tab is fully engaged.
SERVICE & REPAIR PARTS
Refer all service to your local dealer as his knowledge of your
equipment makes him the best qualified source of information.
Order all repair parts through your dealer. Give the following infor-
mation when ordering repair parts: Unit nameplate information
and description of part.
TROUBLE SHOOTING
FILTER TANK LEAKS WATER
*Split in tank due to freeze or other damage. Replace.
*Lid O-ring damaged, twisted, or not lubricated. Inspect.
*Lock ring to lid not tight. Inspect and tighten down to engage lock tabs.
*Air bleed valve loose or O-ring missing. Inspect.
*Inlet/outlet fittings loose or not sealed. Inspect.
DEBRIS BACK TO POOL
*Dirty filter. Clean element in filter cleaner or replace.
*Cracked dirt catcher. Inspect and replace if necessary.
*Filter collapsing. By-pass through top of dirt catcher. Inspect or replace.
*Filter isn't seated in dirt catcher. Inspect.
*Filter is installed upside down. Install top side up. Inspect.
FILTER DOESN'T KEEP WATER CLEAN
*Filter collapsing. Bypass through top of dirt catcher. Inspect or replace.
*Holes in filter. Inspect or replace.
*Filter installed upside down. Inspect or install top side up.
*Filter isn't seated in dirt catcher. Inspect or install top side up.
*Water started out dirty. Continue to filter and clean as necessary.
*Heavy swimmer load. Clean filter as necessary.
*Flow rate too low. Increase flow to turn water more often.
PRESSURE DOESN'T DROP IN FILTER AFTER CLEANING
*Dirty filter. Clean element in filter cleaner or replace.
*Gate valve closed in return line. Inspect.
*Return line partially clogged. Inspect.
*Return fitting clogged. Inspect.
TANK WILL NOT ALIGN WITH BASE MOUNTING HOSES
*Check position of tank. Rotate.
*Loosen pump from base to allow filter to move and align.
FILTER LID LEAKING
*Inspect O-ring, cracks, twisted. Replace.
*Lid cracked. Replace.
*Tank cracked. Replace.
If the recommendations in the TROUBLE SHOOTING portion of
this manual do not solve your particular problem, please contact
your local dealer for service.

3
PARTS FOR MODELS SHER80, 120, 160 AND 200
1
2
3
45
9
6
7
8
10
11
12
FIG. NO.
1
2
3
4
5
6
7
8
9
10
11
12
DESCRIPTION
Ring-LokTM
Cover Latch
Cover Latch (10 per bag)
Air Bleed Valve Knob w/O-Ring
Air Bleed Valve Knob w/O-Ring (50 per bag)
O-Ring 3/16" x 3/8" x 3/32"
Pressure Gauge 0-60# 1/4 CBM
Cover - 80 sq. ft.
Cover - 120 sq. ft.
Cover - 160 sq. ft.
Cover - 200 sq. ft.
O-Ring 11-1/2" x 11-7/8" x 3/16"
Element Assy. 80 sq. ft. 14.59 LG
Element Assy. 120 sq. ft. 20.90 LG
Element Assy. 160 sq. ft. 24.32 LG
Element Assy. 200 sq. ft. 29.82 LG
Microban Element Assy. 80 sq. ft.
Microban Element Assy. 120 sq. ft.
Microban Element Assy. 160 sq. ft.
Microban Element Assy. 200 sq ft.
Dirt Catcher 80 sq. ft.
Dirt Catcher 120 sq ft.
Dirt Catcher 160 sq ft.
Dirt Catcher 200 sq ft.
SherLok 2 Filter Body
SherLok 1-1/2 Filter Body (Systems)
O-Ring
Plug 2" w/O-Ring
Plug 1-1/2" w/O-Ring
PART NO.
42-3671-02-R
42-3677-06-R
42-3677-06-R10
39-2547-01-R
39-2547-01-R50
47-0106-08-R
9193-4182-R
42-2852-05-R
42-2998-00-R
42-3610-00-R
42-3611-01-R
47-0380-47-R
42-3674-09-R
42-3675-08-R
42-3667-07-R
42-3668-08-R
42-3674-19-R
42-3675-18-R
42-3667-17-R
42-3668-18-R
42-2946-03-R
42-2947-02-R
42-3739-02-R
42-3740-09-R
42-3673-00-R
42-3662-00-R
47-0228-01-R
43-3092-02-R
43-3091-03-R
JACUZZI®POOL PRODUCTS - Limited Warranty
Cantar Pool Products (the Company or CPP) warrants Jacuzzi®
pool products to be free of defects in material and workmanship for
a period of 36 months from the date of purchase or 48 months from
the date of manufacture, whichever comes first, with the following
exceptions:
Shaft Seals - For all pumps with the Jacuzzi®patented “dry-run” heat
sink, the shaft seal carries an unconditional warranty against
damage or failure for 2 years from date of purchase/installation.
Light Bulbs - FullMoon Watercolor LED light bulbs are warranted for
1 year from date of purchase; incandescent bulbs are warranted for
90 days from date of purchase.
Misc. - Filter elements, DE grids, white-goods, strainer baskets,
strainer basket “flap” and “priming tube”, pressure gauges, square
rings, o-rings, gaskets, and all replacement parts are warranted for
1 year from the date of purchase.
In order to activate this 3-year warranty, Jacuzzi®
products may be registered with Cantar Pool Products
by either of the following methods:
•Mail-in Warranty Registration Card
•Online at www.cantar.com
This warranty extends only to the original retail purchaser and only
during the time in which the original retail purchaser occupies the
site where the product was originally installed. CPP’s warranty
obligation with regard to equipment not of its own manufacture is
limited to the warranty actually extended to CPP by its suppliers.
THIS WARRANTY IS EFFECTIVE January 1, 2005. ANY IMPLIED
WARRANTIES WHICH THE PURCHASER MAY HAVE, INCLUDING
MERCHANTABILITYANDFITNESSFOR APARTICULAR PURPOSE,
SHALL NOT EXTEND BEYOND THE APPLICABLE WARRANTY
PERIOD. Some US states or Canadian provinces do not allow
limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. IN NO EVENT SHALL CPP BE
LIABLEFORINCIDENTAL ORCONSEQUENTIALDAMAGES. Some
US states or Canadian provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above
may not apply to you.
This warranty applies to products used in swimming pool, spa, &
aquaculture applications only and does not apply to any product
which has been subjected to negligence, alteration, accident,
abuse, misuse, improper installation, abrasives, corrosion and/or
electrolysis, improper voltage supply, vandalism, civil disturbances,
or acts of God (including but not limited to freeze damage, lightening
strikes, and other damage caused by catastrophic events). The only
warranties authorized by CPP are those set forth herein. CPP does
not authorize other persons to extend any warranties with respect
to its products, nor will CPP assume liability for any unauthorized
warranties made in connection with the sale of its products. The
Company will not be responsible for any statements that are made
or published, written or oral, which are misleading or inconsistent
with the facts as published in the literature or specifications furnished
by the Company.
WARRANTY CLAIM PROCEDURE
Warranty claims shall be made by contacting the installing/selling,
builder, dealer, or retailer (point of purchase) or the Jacuzzi®pool
products distributor in your area.
All equipment must be inspected by a local Company representative
or at the factory before warranty is authorized. All charges or
expenses for freight to and from the factory, removal and reinstallation
of the products, or installation of a replacement product are the
responsibility of the purchaser unless otherwise expressly
authorized by Cantar Pool Products. The Company, at its discretion,
may repair or replace free of charge (F.O.B. factory in Toronto,
Ontario) any product that proves defective within the warranty period,
or it may issue credit in the amount of the invoice of the defective
equipment in lieu of repair or replacement. The Company reserves
the right to substitute new or improved equipment on any
replacements.
The provisions of this additional written warranty are in addition to
and not a modification of or subtraction from the statutory warranties
and other rights and remedies provided by any US state law or
Canadian provincial law.

4
325 Humber College Blvd., Toronto, ON, M9W 7C3 .Phone: [phone] .Fax: [phone]
CANTARCANTAR
CANTARCANTAR
CANTAR Pool Products Ltd.Pool Products Ltd.
Pool Products Ltd.Pool Products Ltd.
Pool Products Ltd.
Produits de Piscine Ltée.Produits de Piscine Ltée.
Produits de Piscine Ltée.Produits de Piscine Ltée.
Produits de Piscine Ltée.
Jacuzzi®is a registered trademark of Jacuzzi Inc. and used under license.
6 - 8 PSI
6 - 8 PSI