Jade GIGALINK GLR2702 Manual

ELSEMA
Enter the world of wireless
GLR2702/GLR43302 GIGALINK™RECEIVER SETUP INSTRUCTIONS
The transmitter/receiver can be single or channelised code programmed.
Single Code Programming
This is used for programming one channel at a time to the transmitter. Single code programming can be
achieved by following the steps below:
Step 1: Connect power to the GIGALINK™receiver. Make sure all switches on the mode dipswitch
are off.
Step 2: Momentarily short the two CC pins on the receiver board. (This sets all the channels to a
random code. If there are transmitters previously programmed, they will have to be re-
programmed when CC pins are shorted.)
Step 3: Select the receiver channel, to be programmed, by setting the 2-way dip switch. See dip switch
table below.
Dip Switch
Setting
Receiver Channel
(Output Relay)
Receiver Type
1 2
Off Off 1 GLR2702/GLR43302
On Off 2 GLR2702/GLR43302
Step 4: Connect the transmitter to the receiver by inserting the GIGALINK™cable into the transmitter
and receiver 2.5-mm socket. (This will activate the programming mode and is indicated by the
red light (LED) on the transmitter that must remain “on”)
Step 5: Activate one of the selected channels on the transmitter for approximately one second, LED
should blink twice to confirm code programming and then switch “off”.
Step 6: Disconnect GIGALINK™cable.
Repeat steps 3 to 6 to program another transmitter channel.
Channelised Code Programming
This is used to program all channels from a multi channel receiver to a multi channel transmitter. Channelised
code programming can be achieved by following the steps below:
Step 1: Connect power to the GIGALINK™receiver. Make sure all switches on the mode dipswitch
are off.
Step 2: Momentarily short the two CC pins on the receiver board. (This sets all the channels to a
random code. If there are transmitters previously programmed, they will have to be re-
programmed when CC pins are shorted.)
Step 3: Connect the multi channel transmitter to the multi channel receiver by inserting the
GIGALINK™cable into the transmitter and receiver 2.5-mm socket. (This will activate the
programming mode and is indicated by the red light (LED), on the transmitter that must remain
“on”)
Step 4: Press any two channels simultaneously on the multi channel transmitter for one second, LED
should blink twice to confirm code programming and then switch “off”.
Step 5: Disconnect GIGALINK™cable.
Repeat steps 3 to 5 to program another multi channel transmitter.

ELSEMA
Enter the world of wireless
Different Modes for the Output
Modes are user selectable from the 2-way dipswitch. Dipswitch 1 corresponds to relay channel 1 and
dipswitch 2 corresponds to relay channel 2.
Momentary Mode If the dipswitch is “off” the relay will be in momentary mode.
Flipflop Mode If the dipswitch is “on” the relay will be in flipflop mode.
Latching Mode If latching is required (Relay stays on until power is removed) the latching link
should be inserted and soldered into the two holes to the right of the 2-way
dipswitch. This will enable corresponding relays to latch.
Troubleshooting
This section contains helpful troubleshooting tips and solution.
Symptom Solution
Receiver not responding to transmitter after
programming.
Try to program the transmitter again, but this
time connect battery to the transmitter.
If transmitter only programs when the battery is
connected, return transmitter to Elsema.
Check if GIGALINK™cable is inserted
correctly
Transmitter activates wrong channel on a multi-
channel receiver.
Wrong dip switch setting while programming
the receiver. Use the dip switch table and
program again
Transmitter has short range. Check receiver antenna connection. If you are
using a shielded coax cable, check that the
shield and core are connected properly.
Led is flashing on the transmitter. Replace battery.
JADE safety&securityB.V. T: 030-2250 500 KvK: 16039021
Vlierlaan 5 F: 030-2250 514 Rabobank: 1217.11.757
3735 KT BOSCH EN DUIN E: [e-mail] BTW: NL0046.77.286.B.01
NEDERLAND I : www.jade-bv.nl Leveringsvoorwaarden: zie website