Jakka Pro User manual

KEYPAD AND PANEL DESCRIPTIONS
1. ON—OFF OPERATIONS
Use the key to Opening/Closing operaons.
When pressing the buon once, the device will switch
on or o.
3. SETPOINT SETTING
Use the ▲ and ▼ keys
to adjust the setpoint. If
the keys are pressed
one me, setpoint will
be changed 1 °C. Use
the ▲ key to increase
the setpoint, use the ▼
key to decrease the set-
point. Seng range 5 °
C—30 °C.
O Posion On Posion
2. OPERATION MODE SETTINGS
While the device is in the On Posion, operaon mo-
de can be changed with key.
Note: The acve mode icon ashes on the panel.
Heang or Cooling Mode Venlaon Mode
4. MONITORING DIFFERENT TEMPERATURES
Setpoint Seng
On/O Key
Mode Key
Fan Key
▲ ▼ Increment/Decrement Key
WARNING !!
Parts that need to be considered in the screen shots are
taken into the circle. Please noce the screenshots.
The sensor values, which is measured by main control-
ler, are displayed alternately on the panel. In this appli-
caon “Room Temperature, Supply Air Temperature,
Outdoor Air Temperature, Exhaust Air Temperature”
sensors can be measured by main controller.
Note 1: If Room Temperature Sensor is not connected to
main controller, Temperature Sensor value of the panel is
measured.
Note 2: Supply Air Temperature and Room Temperature
value are measured by same input. If user wants to get the
Supply Air Temperature value, ChangeReturntoSupply para-
meter ( Service Menu 11. parameter, BMS 344. parameter )
must be set to “1”. Aer doing this changing, room tempe-
rature value is measured by panel.
Note 3: If Outdoor Air Temperature Sensor is connected and
necessary sengs are made, electrical heater is controlled
by the Outdoor Air Temperature. Electrical Heater control is
performed by the Return Air Temperature sensor value by
default.
Heating Electrical Heater Stages
Room Tmp
Setpoint
Home İcon
Supply Air Fan Speed
Auto-5-4-3-2-1Exhaust Air Fan Speed
1-2-3-4-5-Auto
Air Quality
Sup. Air Tmp
Cooling Ventilation
Out. Air Tmp
Alarm Notification
Auxiliary Digits
Days
Auto
Main Digits
Keylock
Exh. Air Tmp
MANUAL for JAKKA PRO CONTROLLER

Supply Air Temperature
Room Temperature
Exhaust Air Temperature
Outdoor Air Temperature
5. FAN SPEED SETTINGS
Fan speed can be set to one of 1-2-3-4-5-Auto values.
Supply Air Fan Speed Seng :
When pressing the FAN key once, Supply Air Fan icon
ashes on the panel. While icon ashing, fan
speed can be changed by ▲ and ▼ key.
Exhaust Air Fan Speed Seng :
When pressing the FAN key twice, Exhaust Air Fan
icon ashes on the panel. While icon ashing,
fan speed can be changed by ▲ and ▼ key.
Note: When one of the heang or cooling mode is selected,
automac fan speed is acvated. If the automac fan
speed is selected, fans operates according to the “Air Qua-
lity or Carbon Dioxide Sensor” value. If sensor is not con-
nected, fan speed is decreased to a minimum value.
Supply Speed Seng Exhaust Speed Seng
6. FAN LOGIC SETTING
While the device is in the On posion, if pressing FAN
key for 5 seconds, fan logic is changed.
Connious Fan : Displayed as
“Cont” on the panel. Fans will
work as long as the device is in
the On posion. ( Default )
Auto Fan : Displayed as “Auto”
on the panel. Fans will be acve
while heang or cooling. In other
cases the fan output is closed.
7. CLOCK SETTINGS
When pressing the MODE key for 6-7 seconds, hour
digit ashes on the panel. While digit ashing, hour
can be changed by ▲ and ▼ key.
MODE key is pressed once again, minute digit ashes
on the panel. While digit ashing, minute can be chan-
ged by ▲ and ▼ key.
Hour Seng Minute Seng
8. SCHEDULE OPERATIONS
Aer seng minutes, to enter the schdule menu, press
the MODE key one mes.
While in the "On" or "OF" menu, hour can be changed
by ▲ and ▼ key.
1. Press MODE key to enter the "On" menu. Hour can
be changed by ▲ and ▼ key. "On" menu shows the
opening day and time.
2. Press MODE key to enter the "OF" menu. Hour can
be changed by ▲ and ▼ key. "OF" menu shows the
closing day and time.
Press MODE key (one or more mes) to select the
schedule day.
MANUAL for JAKKA PRO CONTROLLER

"On" Menu "OF" Menu
9. ALARMS
All outputs are closed
except Status Out and By-
pass Damper O. The Pa-
nel locked. Contact must
be in the closed posion to
eliminate the alarm.
9.1 AL:01 FAN CONTACT ALARM (NC)
Fans run at maximum
speed during alarm. The
Panel locked. The device
resumes normal operaon.
Contact must be in the
opened posion to elimi-
nate the alarm.
9.2 AL:02 HUMIDITY SENS. CONTACT ALARM (NO)
If contact is in the closed
posion or when device
worked up to the AirFilter-
TimerLimit, alarm hap-
pens. Device is connuing
normal operaon during
alarm.
If the Alarm number is 04
(AL:04) and the air lter alarm is caused by AirFilterTi-
merAlarm, the related parameter (BMS 331., Service
Menu 8. parameter) must be set to 0 to reset the
alarm.
9.4 AL:04 AIR FILTER ALARM (NO)
If contact is in the opened
posion, alarm happens.
Electrical heater outputs
are closed. Fans run at
maximum speed. The Pa-
nel locked. Contact must
be in the closed posion to
eliminate the alarm.
9.5 AL:05 ELEC. HEATER OVER HEAT ALARM (NC)
If Outdoor Air Temperatu-
re < -8 and Exhaust Air
Temperature <= 2 alarm
happens.
Electrical Heater 1. stage
opens during alarm.
When Exhaust Air Tempe-
rature > 2 and me passed
up to the OutdoorTempFrostOutTimerLimit (BMS 331.
parameter), alarm is eliminang.
9.6 AL:06 OUTDOOR TEMP. SEN. FROST ALARM
9.3 AL:03 FIRE CONTACT ALARM (NO)
If contact is in the closed
posion or Room Tempe-
rature > SetFireA-
larmTemp (BMS 343.,
Service Menu 44. para-
meter), alarm happens.
Supply air fan is closed, Exhaust air fan runs at maxi-
mum speed. All outputs are closed except Status Out
and Entrance Damper. The Panel locked. Eliminang
the alarm and disconnect the power of the device to
return to normal operaon.
Note 1: Aer the device restarted, press together MODE and
▲ buon unl unlock the device.
Note 2: SetFireAlarmTemp parameter default value: 50 °C
7. ÖZEL KONTROL FONKSİYONLARI
7.1 HAVA KALİTESİ VEYA CO2 KONTROLÜ
0-10V air quality or CO2
sensor must be connected
properly. Operaon mode
must be set to other than
venlaon (heang or
cooling) and fan speed
must be set to Auto.
When these condions are met, the fan speed is cont-
rolled according to the air quality or CO2 sensor value.
10. SPECIAL CONTROL FUNCTIONS
10.1 AIR QUALITY OR CO2 CONTROL
MANUAL for JAKKA PRO CONTROLLER

10.5 REMOTE CONTROL
The remote On/O funcon. This contact can be used
to control the device via building automaon/PLC/
External Switches.
To use this feature, selected scenario must be contain
remote control contact.
10.2 ELECTRICAL HEATER CONTROL
1. Controlled Depending on Room Temperature :
Electrical heater is controlled by sensor on the panel or
return air temperature sensor. Control is acve without
any adjustment. ( Default Control Type )
2. Controlled Depending on Outdoor Temperature: If
outdoor temperature value less than value set in the
service menu, the heater stages is acvated.
Note: Control according to the outdoor air temperatu-
re to be acve, parameter sengs must be made of
appropriate. (See. Service Menu Operaons)
10.4 ENTRANCE DAMPER CONTROL
Fresh air and/or exhaust air damper motors are cont-
rolled. Damper motor is controlled considering the ne-
cessary delays ( The device On/O moments, alarm
moments... ).
10.3 BYPASS DAMPER CONTROL
The working condions of the bypass damper is as fol-
low;
Fan Mode;
Bypass damper is always closed.
Heang Mode;
1. Outdoor Air Temp. < Room Temp. + 3 and
Setpoint < Room Temp. + 2 and
Outdoor Air Temp. > 15 °C
damper is open,
2. Outdoor Air Temp. > Room Temp. - 3 and
Setpoint > Room Temp. - 2 and
Outdoor Air Temp. < 35 °C
damper is open, closed in the other condions
Cooling Mode;
1. Outdoor Air Temp. > Room Temp. + 3 and
Setpoint > Room Temp. - 2 and
Outdoor Air Temp. < 32 °C
damper is open,
2. Outdoor Air Temp. < Room Temp. - 3 and
Setpoint < Room Temp. - 2 and
Outdoor Air Temp. > 10 °C
damper is open, closed in the other condions
11. SERVICE MENU OPERATIONS
11.1 MENU DESCRIPTION
While the device is in the O Posion, press together
MODE and ▼ key for 5 seconds.
In the service menu “Main Parameter” is replaced by
the MODE and FAN keys.
“Auxiliary Parameter” is replaced by the ▲ and ▼
keys.
Main Parameter Auxiliary Parameter
11.2 PASSWORD PARAMETER
While the device is in the O Posion, press together
MODE and ▼ key for 5 seconds.
To make changes in the parameters, password must be
entered as “137”, to 99.
parameter.
Firstly, “Main Parameter”
must be replaced as 99, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” must be replaced as
137, by the ▲ and ▼ keys.
Otherwise, made changes won’ t be saved.
Note: This process is part of the entry to the Service
Menu and must be applied in all entries.
MANUAL for JAKKA PRO CONTROLLER
One relay output reserved into for damper. If there are
more damper motor, must be connected in parallel.
Note : Damper motor must be in the On/O and
spring return property.

7. ÖZEL KONTROL FONKSİYONLARI
11.4 SETPOINT LIMIT OPERATIONS
Minimum Limit: Firstly,
“Main Parameter” must be
replaced as 2, by the MODE
and FAN keys.
Secondly, “Auxiliary Para-
meter” can be selected in
the range of 5-35 °C, by the
▲ and ▼ keys. (Default
value: 05 °C)
Maximum Limit:
Firstly, “Main Parameter”
must be replaced as 3, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” can be selected in
the range of 5-35 °C, by the ▲ and ▼ keys.
(Default value : 30 °C)
Note 1: Minimum Limit can not be greater than maxi-
mum limit.
Note 2: Maximum Limit can not be lower than mini-
mum limit.
11.3 BMS ADDRESS SETTING
After logging into the servi-
ce menu, using the MODE
and FAN keys, select the 00.
parameter.
Use the ▲ key to increase
the address, use the ▼ key
to decrease the address.
Seng range 0-247.
11.5 ELECTRICAL HEATER CONTROL SETTINGS
Electrical heater can be controlled according to the
two dierent temperature value.
01 : Controlled Depending on Room Temperature :
Electrical heater is controlled by the sensor on the pa-
nel or return air temperature sensor. Control is acve
without any adjustment. ( Default )
02 : Controlled Depending on Outdoor Temperature:
Electrical heater is controlled according to the
“Outdoor Air Temperature Sensor” connected on the
main controller. Enter the service menu to acvate the
control according to the outdoor air temperature.
Outdoor Control Acvate:
Firstly, “Main Parameter”
must be replaced as “9”, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” must be replaced as
“2”, by the ▲ and ▼ keys.
11.6 DATE SETTINGS
1. Firstly, “Main Parameter”
must be replaced as 12, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” must be set to the
desired day value.
2. Firstly, “Main Parameter”
must be replaced as 13, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” must be set to the
desired month value.
3. Firstly, “Main Parameter”
must be replaced as 14, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” must be set to the
desired year value.
Note: When the specied steps are correctly completed,
device will choose day of week correctly.
Setpoint Seng:
Firstly, “Main Parameter”
must be replaced as “10”,
by the MODE and FAN
keys.
Secondly, “Auxiliary Para-
meter” must be selected in
the range of 0-20 °C, by the ▲
and ▼ keys.
(Default value : 15 °C)
Note: If outdoor air temperature value lower than
value set in the service menu, the heater stages is
acvated.
Set
Control Activate
This parameter used to correct changes made by mista-
ke.
Firstly, “Main Parameter”
must be replaced as 15, by
the MODE and FAN keys.
Secondly, “Auxiliary Para-
meter” must be replaced as
1, by the ▲ and ▼ keys.
When the device returned factory defaults, parameter
value is set to "0" automacally. (Default value = 0)
11.7 FACTORY DEFAULT
MANUAL for JAKKA PRO CONTROLLER

1) Use standart juncon box.
Hole distance must be 60mm
center to center.
Use 68mm hole saw.
2) Remove the
front panel
using a thin-
blade at
screwdriver.
3) Secure the
rear panel by
screwing screws.
Necessary
screws are in the
box.
4) Make the
cable connec-
ons as shown
below to termi-
nals on the front
panel.
5) Aach the clip
at the top rst,
and then aach
the clip at the
boom.
13. CONTROL PANEL CABLE CONNECTIONS
(2 x 2 x 0,34...0,75mm²)
Shielded, Twisted Pair, RS485 Data Com-
municaon Cable must be used.
Note : Press the terminal buons with
the help of a ne-pped pen as shown
in the gure. Don't apply extreme
pressure.
NOTE: DON’T USE THE SCREWDRIVER
12. MOUNTING INFORMATION
MANUAL for JAKKA PRO CONTROLLER