JAMES MARTIN VANITIES TAMPA 901-M23.6-GW User manual

LED Mirror - Installation Instructions
IMPORTANT: Please read all instructions prior to beginning the installation of this mirror
James MartinVanities always recommends you hire or consult a professional contractor when installing our products
Note: This mirror is not intended for outdoor use
J A M E S M A R T I N V A N I T I E S
• Make sure the installation area is free of clutter.
• Turn off electricity including wall switch's.
• Do not modify wires in anyway
• Always use two or more person when hanging mirrors
•Parts included
2pcs
Electrical Cord
(attached to back of mirror)
Mirror
( 13*50)
901-M23.6-GW TAMPA MIRROR
B
A
Made in China
Page 1 of 6
Drywall Anchors X FEATURES
CODES / CERTIFICATIONS
• 5020102
•5mm copper free silver mirror
•High output LED light:2550-2650LM,4000K CCT
•Touch switch for surface LED
Version:202107
KLRA5E1S17959H3B1P1D
Screws X 2pcs
( 68*20 )

• 120 Vac 60Hz wall outlet location - Required for source power
• Mirror hangs in Portrait orientation
• Includes hardware with easy installation via Plug and Hang Systen
Pre-Installation Notes
Made in China
Page 2 of 6
Back view Front view Side view
1 1/2"[39mm]
901-M23.6-GW TAMPA MIRROR
Mirror Weight: 21.85Ibs (9.93kgs)
Touch the Sensor switch
23 5/8"[600mm]
31 1/2"[800mm]
22 5/8"[576mm]
30 1/2"[776mm]
8 1/4"[210mm]
8 1/4"[210mm]
∅8 1/4"[ ∅210mm]
∅5 1/8"[ ∅130mm]
Open area in back cover
for electrical cord storage
28 3/8"[720mm]
3 7/8"[100mm]
15"[380mm]
9 7/8"[250mm]
3 7/8"[100mm]
14 7/8"[379mm]
Version:202107
KLRA5E1S17959H3B1P1D

Tools required
Screw driver Drill with 3/8" bit Pencil Measuring Tape wrench level The hammer
Measure the distance between the bottom
of the mirror and point a. Measure the
distance between c and d
A
B
a
a
1 2 3
4 5 6
Draw a horizontal line from the point a using a level Draw point c and point d
Drill the holes on the wall and insert
the drywall anchors into the holes.
Insert the screws into the drywall anchors and reserve 16mm on the outside Hang the mirror on the screws
b
BACK
OF THE
MIRROR
NOTE: Always use two or more
people when hanging mirrors
WALL
MIRROR
Made in China
Page 3 of 6
cd
d
c
HANG SYSTEM
901-M23.6-GW TAMPA MIRROR
Mirror Weight: 21.85Ibs (9.93kgs)
Version:202107
KLRA5E1S17959H3B1P1D
UP

•Care and Cleaning Instructions for Mirrors
•CLEANER
The best and safest cleaner for a mirror is clean, warm water used with a soft cloth. Be careful not to allow
the edges of the mirror to get or remain wet over a period of time. If using a commercial glass or mirror
cleaner, be sure to use a standard brand of mirror cleaner that does not contain ammonia or vinegar.
•APPLICATION
Never spray any cleaner directly on to a mirror. Instead apply the cleaner to a soft cloth and then wipe the
mirror.
•CLOTHS
Always use soft, grit-free cloths when cleaning a mirror to reduce chances of scratching the surface.
• FINISH
Be sure to dry all joints and edges thoroughly to be certain no commercial cleaner comes in contact
with the edge and backing.
901-M23.6-GW TAMPA MIRROR
Made in China
Page 4of 6
Version:202107
KLRA5E1S17959H3B1P1D

Made in China
Page 5of 6
901-M23.6-GW TAMPA MIRROR
Version:202107
KLRA5E1S17959H3B1P1D
ELECTRICAL SAFETY INSTRUCTIONS:
All connections must be installed by a licensed electrician, in accordance with current building codes. Consult a qualified
electrician.
IMPORTANT:
Always switch off the electrical supply at the main during installation and maintenance. It is recommended that the circuit
breaker is switched off for the necessary circuit before installation commences.
Fitting in Bathrooms is subject to the appropriate building code Regulations. This product is NOT suitable for outside zones. It is
also Not suitable for installation in saunas, steam rooms or shower cubicles. This product is only suitable for permanent
installation. DO NOT connect to a trailing plug and socket outlet. This product is only suitable for indoor use. Do not attach the
product to surfaces that are damp or otherwise electrically conductive.
INSTALLATION CARE & SAFETY:
Wear suitable eye protection when drilling. Take care when using power tools. Beware of hidden cables or pipes. Take care if
drilling on tiled surfaces in case the drill slips. A piece of masking tape applied to the wall before marking out the fixing holes will
stop the drill from wandering.
CLEANING:
It is recommended that the unit is cleaned with a soft,dry, non abrasive cloth when turned off. Never use cleaning agents or
abrasive materials on any type of surface finish. Do not allow moisture to come into contact with the electrical components.
IMPORTANT:
DO NOT strike glass components with hard or pointed items. DO NOT place very hot or very cold items against or in close
proximity to glass surfaces unless an adequately thick insulation material is used to prevent such items coming in contact with
the glass. The nominal thickness of the mirror glass used in this product is 1/5” and is film backed for safety. If the glass
becomes chipped or broken replace immediately.
MANUAL INSTRUCTION：
1) Short Touch the switch button (＜1s) to turn the light and defogger ON/OFF.
2) Long Touch the switch button (＞1s) to activate the dimming function. Adjust the light to the appropriate brightness.

Made in China
Page 6of 6
901-M23.6-GW TAMPA MIRROR
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical furnishing, basic precautions should always be followed, including the following. Read all instructions before using (this furnishing).
DANGER - To reduce the risk of electric shock:
Always disconnect this furnishing from the electrical outlet before cleaning.
WARNING -To reduce the risk of burns, fire, electric shock, or injury to persons.
1 -Disconnect from outlet before putting on or taking off parts.
2 -Close supervision is necessary when this furnishing is us.ed by, or near children, invalids, or disabled persons.
3 -Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
4 -Never operate this furnishing if it has damaged , not working properly, dropped or damaged, or dropped into water. Return the furnishing to a service
center for examination and repair
5 -Keep the cord away from heated surfaces.
6 -Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
7 -Never drop or insert any object into any opening.
8 -Do not use outdoors.
9 -Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
10 -To disconnect turn all controls to the off position, then disconnect from outlet.
11 -For grounded products the following statement:
"WARNING: Risk of Electric Shock - Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
SAVE THESE INSTRUCTIONS
12 -GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit
conductors and connected to the equipment-grounding terminal or lead on the product.
Version:202107
KLRA5E1S17959H3B1P1D