Jands JS-B001 User manual

Product Manual Smart TV Controller-3D Motion Sensing
Product Manual
Thanks for purchasing J&S’s innovative products!
For better user experience, please take time to read the instruction manual carefully in order
to acquire full knowledge and understanding of our products before you start.
Declaration
The specifications and information stated in this manual is for your reference only, and
further updates may be released without advanced notice.
All content in this manual contains no guarantees or warranties for any particular
purpose. Considering the fast-paced technological developments as well as the
complexity of its operating systems, there exist some mistakes or outdated information,
or some information that may not be applicable to certain situations. Our company and
subordinate employees could thus obtain no obligation for such discrepancies.
Warnings:
2.4 GHz wireless transmission is applied to the product. This is considered to be harmless
to human body (less radiation than mobile phones). It meets European R&TTE Directive
1999/5/EC requirements. However, wireless transmission generates electromagnetic
wave somehow, so use with caution where cardiac pacemakers or other relevant
assisting medical equipments be applied.
Do not expose the product to liquid or moist environment.
When there is a dramatic change in the surrounding temperature, cursor may drift for
several seconds.
Please do not attempt to dismantle and repair the device on your own.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device

Product Manual Smart TV Controller-3D Motion Sensing
must accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Product Manual Smart TV Controller-3D Motion Sensing
Contents
Product Information
Introduction
Package
Product ID Outlook
Quick Guide to Motion Sensing TV Controller
Instructions
Turn on the TV Box and Controller
Receiver
Manual Connection
Working State
Battery
Led Light Indicator
Air Mouse Control Function
Calibration
Hibernation Mode/Wake-up/Active Mode
Specifications
Contact Information

Product Manual Smart TV Controller-3D Motion Sensing
PRODUCT INFORMATION
Introduction
Facing the new generation of smart TVs or PCs applications, the traditional control products
such as the table mouse, keyboard and infrared TV remote have become increasingly
inadequate. J&S’s controller product solutions provide users with smart and full-functional
interfacing capabilities with smart TVs or PCs. The innovations of developing and integrating
state-of-the-art control technologies into smart control products can deliver versatile control
methods, as well as user-friendly interfacing experience.

Product Manual Smart TV Controller-3D Motion Sensing
Package
The packaging box contains the following items:
3D Motion-Sensing Smart TV Controller
Rechargeable Lithium-ion Battery
USB Receiver (stored under the back cover of controller)
User Manual
USB Cable (For charging)
Production Certification

Product Manual Smart TV Controller-3D Motion Sensing
Product ID Outlook
Front view

Product Manual Smart TV Controller-3D Motion Sensing
Back View
Quick Guide to Motion Sensing TV Controller
Connect with TV Box with a USB dongle
The USB dongle is stored at the battery container of the device. Uncover the batter
container in the back, take out the dongle and plug it into the TV box intended to
connect with.
Turn ON/OFF
Turn on the control device. Power ON/OFF switch is on the back of the controller, switch
ON or OFF to turn on or off the control device, respectively.
Power On
Keep the device to face-up position and stable for a few second till the led indicator
lights on in blue. The led indicator will stay on in blue light for 30 seconds, if it is turn on
properly.
Pairing
If the pairing key is pressed accidentally, the led indicator will flash in red for 60 seconds.

Product Manual Smart TV Controller-3D Motion Sensing
Please wait with patient, once the red flashing light goes off, the device get ready for
use.
Active Mode
Under Active Mode, when there is any detectable movement associated with the device,
the led indicator will keep flashing in blue; and when there is no movement, the blue
light goes off automatically.
Air Mouse Control Function
This product performs precise and stable mouse control function by hand movements (a
more effective way, as suggested, is to control by wrist instead of by arm movements). It
can also perform drag function by moving the cursor to the selected object, then press
and hold the OK button. Release the OK button when the object is dragged to the
intended position.
Calibration
It is due to the nature of motion sensing mechanism. While using the controller,
sometimes you may find the cursor is not well placed in accordance with the position
you want. For example, you want the cursor to keep moving to the right while your wrist
reaches its maximum range to the right. At this point, you just need to give the
controller a little shaking horizontally. The controller will then recalibrate itself and the
cursor should resume to the position you feel comfortable with.
Sleep Mode and Wakeup Mode
The device turns into Sleep Mode automatically once the device is left in no use for a
while, and the device can be woken up any time when it is picked up. However, there exit
chances that some movements might be too weak to activate the device. When it is the
case, a little shake should help wake it up.
Charging
With Power Switch on, the device starts being charged when it is connected with the TV
box via a USB cable or to any power adaptor with USB plug-in. The led indicator should
keep flashing in blue light during the course of charging, and the blue light should keep
on till the USB cable is disconnected.
Low Battery

Product Manual Smart TV Controller-3D Motion Sensing
Anytime when the device detects low battery power (<10%), the led indicator should
start flashing in red light for 30 seconds in every 3 minutes.
Surrounding Temperature
When there is dramatic change in the surrounding temperature, it may cause the cursor
drifting somehow. For example, when the device is brought into an air-conditioned room
from hot outside, a few seconds of cursor drifting may occur to the device.
INSTRUCTION
Turn on the TV box and Controller
Turn on the motion-sensing smart TV controller, the switch-on button is located at the
back of controller;
Click the TV box power button to turn on the Android TV box. The power control key is
located at the top left side of the controller. ,
Receiver
The accompanied USB receiver is stored in the slot section under the battery cover. Plug the
USB receiver into the USB port in the TV box.
Manual Connection
In case that the controller is not automatically connected to the box after turning the unit on,
press the pairing key and the Led indicator will begin flashing; unplug the receiver and
re-plug it into the box. Once it connects successfully, the Led light indicator on the front of
controller will stay blue for 30 seconds.

Product Manual Smart TV Controller-3D Motion Sensing
Battery
This product is equipped with 800mAh lithium-ion battery. It is only partially charged before
delivery. Please fully charge the battery before initial use. It is suggested that the battery be
fully charged and discharged the first several times for longer battery life.
1. Connect the Controller via the USB cable with the TV box to get charged.
2. The Controller can also be charged by connecting it to a PC via the USB cable.
3. It normally takes 4-5 hours to fully charge the battery from a complete discharge. It takes
longer to fully charge if the controller is in use while charging.
For information about battery level or charging status, please refer to the "Led Light
Indicator” section.

Product Manual Smart TV Controller-3D Motion Sensing
Led Light Indicator
The dual colored LED indicator (Red/Blue) is located in the upper front of the controller. The
light indications of different status are described as follows:
Condition
Color
Description
Active Mode (with operations)
Blue
Stable blue light
Active Mode (with no operation)
Off
Battery level less than 10%
Red
Flash per 0.5 second for five times
with 5 min interval;
Battery level less than 5%
Red
One flash every 1 second
Charging
Blue
Flash every 2 seconds
Fully charged
Blue
Stable light until disconnection
Battery level more than 10% & Turn on the
controller
Blue
Keep flashing for 15 seconds
Batter level less than 10% & Turn off the
controller
Red
Flashing for 15 seconds
Connecting manually
Blue
Rapid flashing every 250ms
Manual connection success
Blue
Stable light for 5 seconds
Manual connection failure
Red
Stable light for 5 seconds
Battery level more than 10% & Wake-up
status
Blue
Stable light for 10 seconds
Battery level less than 10% & Wake-up status
Red
Flashing for 10 seconds
Total: 8 Led Light Indicator Mode
Mouse Control Function
The controller is built in with a 3D motion sensing engine, a motion capture system used for
input devices. It adopts a 3-axis gyroscope and a 3-axis accelerometer to calculate projected
X and Y displacement, roll angle, rotation intensity and force intensity. By fusing the
gyroscope and accelerometer outputs, an adaptive reduced filter algorithm is also used to

Product Manual Smart TV Controller-3D Motion Sensing
compensate for the most significant inertial sensor errors in attempt to achieve precise and
stable motion control in the air.
This product performs precise and stable mouse control function by hand movements (a
more effective way, as suggested, is to control by wrist instead of by arm movements). It can
also perform drag function by moving the cursor to the selected object, then press and hold
the OK button. Release the OK button when the object is dragged to the intended position.
Calibration
It is due to the nature of motion sensing mechanism. While using the controller, sometimes
you may find the cursor is not well placed in accordance with the position you want. For
example, you want the cursor to keep moving to the right while your wrist reaches its
maximum range to the right. At this point, you just need to give the controller a little shaking
horizontally. The controller will then recalibrate itself and the cursor should resume to the
position you feel comfortable with.
Hibernation/Wake-up/Active Mode
Hibernation: Goes on hibernation after 30 seconds rest;
Wake-up: The device can be woken up any time when it is picked up. However, there exit
chances that some movements might be too weak to activate the device. When
it is the case, a little shake should help wake it up.
Active Mode: The blue LED indicator is on when moving the controller.

Product Manual Smart TV Controller-3D Motion Sensing
SPECIFICIATIONS
System support
Android 2.2/2.3 to 4.0
Control technology
3D Motion Sensing Control technology;
equipped with a 3-axis gyroscope and a
3-axis acceleration sensor
Connection
2400MHz-2483MHz
Interface type
Micro USB
Battery
800mAh lithium battery; charging battery
using USB connection
Operating distance
10m
Length
158mm
Width
42mm
Thickness
12.4mm
Weight
80g～85g
Voltage
Less than 20mA @ 3.3V & Working Status
About 250uA & Hibernation Status
Environmental specifications
Low standby power consumption
CONTACT INFORMATION
J&S Technology & Development Co., Ltd.
Unit 806, Tower A, Skyworth Bldg., Gaoxin South 1st Ave.,
Hi-Tech Industrial Park, Nanshan District, Shenzhen, China
Tel: [phone] Fax: [phone] Zip code: 518057
E-mail: cont[email protected]om
Website: www.jnselectronics.com