Jaypro Sports FSG-1 User manual
- - Page 2of 5
FSG-1
PARTS LIST (QTY: SINGLE UNIT)
ITEM
IMAGE
DESCRIPTION
QTY
1
73 3/4" LONG UPRIGHT
FSG-1-A1
2
2
34 9/16" LONG BASE
FSG-1-A2
2
3
BACKSTAY 1.90 DIA
FSG-BS1
2
4
116 1/8" LONG CROSSBAR
FSG67910-5
2
5
Classic Cast Corner - Machined
SG-L
4
6
Bottom RCG Cast Corner - Machined
SG-K
2
7
3/8-16 UNC-Nylon Lock Nut-SS-GrNC
HN5003
4
8
3/8" FLT SAE, SS
HW2151
24
9
3/8" MEDIUM SPLIT LOCK WASHER, SS
HW2152
24
10
3/8-16 x 1 HEX BUTTON CAP SCREW-SS
HS5244
24
11
3/8-16 x 3 HEX BUTTON CAP SCREW-SS
HS5203
4
12
FUTSAL GOAL REPLACEMENT NET
FSG67910N (COLOR COMES IN WHITE)
1
13
NET CLIPS
ENC-824
1
- - Page 3of 5
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
Tools Require:
1
Rubber Mallet
1
9/16" Socket Wrench or Box Wrench
1
7/32" Allen Wrench
oUnpack all parts and check against parts list to ensure that all have been
included.
oInspect all parts for damage. Report any damages to the trucking
company.
oTools required: tape measure, step ladder
* Extra screws are included, discard or stow away as needed.
- - Page 4of 5
ASSEMBLY (REQUIRES 2 PEOPLE):
1) Unpack all parts and check against parts list to ensure that all parts have been included.
2) Inspect for damage. Report all damages to trucking company.
3) Lay parts out on clean dry floor.
4) Assemble both side frames, as shown in Figure 1 (note the orientation of the safety
labels). The corner fittings having floor pads, go on the bottom of the frame. Installation
hint: Assemble the base (items 2, 5 & 6). Next assemble the upright (1) top corner fittings
(5) and backstay (3) as one. Then slide this onto the pre-assembled base.
5) Hold one side frame goal face down on the floor. Carefully insert the top crossbar onto
the front corner fitting of the side frame (be sure to note the orientation of the labels).
Carefully insert the rear crossbar onto the rear corner fitting. While holding the free end
of the rear crossbar, slide the other side frame onto both crossbars. Be sure to slide the
fittings on evenly to avoid binding.
- - Page 5of 5
6) Loosely install all hardware. Ensure goal is square and corners fully inserted and then
tighten hardware.
7) Drape the net over the goal and secure net to the extrusion using the net clips. Note the
top corner of net has a label.
8) To minimize the amount of sag across the back of the net, tie off the cord that passes
across the back corner of the net to the backstays.
Table of contents
Other Jaypro Sports Accessories manuals
