Jaypro Sports CVAC66 User manual

Rev: - [Type text] Page 1of 14
-- CVAC66 --
(THE TITAN CVX2 OUTDOOR ADJUSTABLE w/ ACRYLIC)
Installation Instructions
Keep this instruction manual in case you have to contact the manufacturer for replacement parts.
!
!
WARNING
DO NOT ATTEMPT TO ASSEMBLE THIS
SYSTEM WITHOUT CAREFULLY
READING AND FOLLOWING ALL
I N S T R U C T I O N S B E G I N B Y
I D E N T I F Y I N G A N D T A K I N G
INVENTORY OF ALL PARTS USING THE
P A R T S L I S T P R O V I D E D .
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com
FAILURE TO COMPLY WITH ANY OF
T H E W A R N I N G S I N T H E S E
INSTRUCTIONS MAY RESULT IN
S E R I O U S P E R S O N A L I N J U R Y .
FAILURE TO COMPLY MAY ALSO
RESULT I PROPERTY DAMAGE. PLEASE
HEED ALL WARNINGS AND CAUTIONS
T O E N S U R E Y O U R S A F E T Y .

Rev: - [Type text] Page 2of 14
1) 2 Adjustable Wrenches
9) Shovel
2) Socket Set
10) Concrete 1/2 yard or 14-
16 Bags, (80 lbs. bags)
3) 9/16” Wrench
4) 3/4" Wrench
11) Philips Head Screwdriver
5) 15/16” Wrench
12) 2 Ladders (min.) or Crane
6) 1/2" Wrench
13) Carpenter’s Level
7) Hammer or Mallet
14) Water Supply
8) Tape Meaure
TOOLS AND MATERIALS REQUIRED FOR ASSEMBLY
(Not Included)
BEFORE YOU START
Identify and inventory all parts using the checklist boxes in the parts list.
Be sure to keep the hardware bags and their contents separate.
Test fit all Bolts by inserting them into the respective hole. If necessary,
carefully scrape away any excess powder coating buildup from inside the
holes. Do not scrape away all of the powder coating. Bare metal may rust.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID THE WARRANTY.
●A minimum of six adults are required to safely assemble the unit.
●The major components of this system have considerable weight. It is recommended that
scaffolding and/or a lift jack be used to hoist the post, outrigger, braces and board into place.
●If using a ladder during assembly, use extreme caution. Follow all warnings and cautions on the
ladder carefully.
●A probability of serious injury exists if this system is not installed, maintained, or operated
properly.
●Before digging, contact the appropriate agency to locate underground power cables, gas, and
water lines. Do not install the system within 20 feet of overhead power lines.
●Climate, corrosion, or misuse could result in system failure.
●If technical assistance is required, contact the manufacturer.
●Most injuries are caused by misuse and /or failure to follow instructions.
●Use caution when using the system.
!
!
SAFETY INSTRUCTIONS

Rev: - [Type text] Page 3of 14

Rev: - [Type text] Page 4of 14
Spacer Kit:
a. Attached the backboard mounting bracket (N) to the spacer backboard (S1) as shown, with
3/8” x 1 1/2” hex bolt (S2), lock washer 3/8” (S3) and washer 3/8” (S4).
NOTE: spacer is only for 42” x 72" rectangular acrylic backboard (ACRB-72) only, discarded
the other instructions.

Rev: - [Type text] Page 5of 14
INSTALLATION TIP / REFERENCE OVERALL VIEW
48” REF
58” REF
21”

Rev: - [Type text] Page 6of 14
Footing:
NOTE: Before digging, call to locate any buried utility lines.
a. Dig a hole 48" deep x 21" across. The edge of the hole should be flush with the edge of
the playing surface. If you live in an area where heavy frost can occur, it may pose a
problem, consult your local building inspector to determine the appropriate hole depth.
NOTE: The hole must be at least 48" deep.
b. There must be at least 3 feet of clearance behind the unit to enable the user to adjust the
height.
c. Mix the concrete according to the instructions on the bags. Note that a thicker mix of
concrete will dry stronger than a thin mix. Pour the concrete into the hole, stopping
approximately 18 inches from the top of the hole.
d. Assemble the ground anchor kit as shown below.
e. Insert the four pieces of 1/2” x 36” rebar into the hole, pushing each piece firmly to the
bottom of the hole. The four pieces should be arranged in a square approximately 8 - 9
inches wide so that each piece of rebar will be positioned surrounding the backstop post.
f. Finish filling the hole to the top with concrete. And insert the ground anchor kit on top of
the concrete.
g. Allow the concrete to cure a minimum of 72 hours before proceeding. In humid climates
or wet weather, allow additional time for the concert to cure.
Ground Anchor Kit:
Thread a M18 Hex Nut onto each of the J-Bolts. Securely tighten the Nuts all
the way down to the end of the threads. Slide the threaded ends of the J-Bots
through the holes in the corners of the J-Bolt Template and secure them with
M18 Hex Nuts as shown. Securely tighten all Nuts at this time.
NOTE: Make sure the curved “J” ends of the J-Bolts are oriented in a rectangular
pattern as shown.

Rev: - [Type text] Page 7of 14
Step 1:
a. Slide a 18mm thick washer (U3) over each of the J-Bolts (U2) as shown in FIGURE 1A.
b. Remove the padding from main post (A). Place he main post (A) over the J-Bolts. Slide a 18mm
thick washer (U3), a Lock washer 18mm (U6) and thread a 18mm hex nut (U4) to each J-Bolt.
Tighten the nuts only a few turns onto the J-Bolts as shown in FIGURE 1B.
c. If the main post (A) is not exactly vertical, adjust the 18mm J-Bolt hex nuts (U4) located under the
post base. Tighten all of the hex nuts (U4) above post base when main post (A) is vertical.
NOTE: Face the main post (A) with actuator bracket facing away from playing court
(as shown in FIGURE 1C).
FIGURE 1A
FIGURE 1B
FIGURE 1C
Playing Court
Back

Rev: - [Type text] Page 8of 14
Step 2:
a. Slide the main extension arm (F) over the top of the main post (A) and attach to the lower
pivot tube with a M18x320mm Hex Bolt (#5), two M18 flat washer (#11), two nylon
washers M18 (#1) and one lock nut M18 (#14).
NOTE: Make sure nylon washer located between main extension arm (F) and post (A).
the nylon washers may be factory-assembled.
Nylon washer #1 may be factory installed.

Rev: - [Type text] Page 9of 14
Step 3:
a. Connect actuator to main extension arm. Place the upper bracket of actuator (B) between the
last set of welded tubes on the main extension arm (F), attach the two parts using hex bolt
M18x320mm (#5), two flat washers M18 (#11), on lock nut (#14).
b. Connect actuator (B) to the mounting bracket welded in the middle of post (A), using one hex bolt
M16x135mm (#9), two flat washers for M16 bolt (#12), two nylon washers (#2), and one lock nut for
M16 bolt (#15).
NOTE: Make sure nylon washer go between actuator and mounting bracket.
c. Attached crank handle to the actuator. Slide removable crank handle onto the shaft
sticking out of gear box (actuator), lock it in place with attached pin.

Rev: - [Type text] Page 10 of 14
Step 4:
a. Slide steel sleeve (J) thru both tubes welded at the top end of spring-assist cartridge (C).
Place the top of spring-assist between main extension (F), align the steel sleeve (J) with the
second set of welded tubes on the main extension arm (F), place the stainless-steel rim
height indicator (K) beside the spring-assist cartridge (C). Slide one washer M16 (#12) over
one hex bolt M16x320mm (#7) and slide this bolt all the way thru main extension arm (F),
one nylon washer M16(#2), steel sleeve (J), rim height indicator (K), another nylon washer
(#2), and the other side of main extension arm (F). secure it with one flat washer M16 (#12),
one lock nut M16 (#15), Do not over tighten this bolt because this is the pivot point. Mack
sure the rim height indicator (K) hang freely alongside of spring-assist cartridge (C).
NOTE: Nylon washer locates between steel sleeves (J) and main extension arm (F),
they may be factory-assembled already.
b. Attach the bottom of spring-assist cartridges (C) to the main post bracket by using a hex
bolt M16x185mm (#8), two flat washers M16 (#12), one nylon washer M16 (#2) and one
hex nut M16 (#15).
NOTE: Nylon washer goes between two cartridges.
c. Remove and discard the steel spreader bracket from the spring-assist cartridges.