Jaypro Sports PBS-10 User manual

1
2
3
4
5
6
8
SEE DETAIL
'A-A'
PLAYER BENCH WITH SHELF
PRODUCT NAME:
JAYPRO
SPORTS
JAYPRO
SPORTS
976 HARTFORD TURNPIKE
WATERFORD, CT 06385 USA
PHONE [phone]
FAX [phone]
WWW.JAYPRO.COM
MODEL. NO:
DRAWN BY: 6/5/2019
PBS-10/PBS-20/PBS-80/PBS-90
J.A. / A.T./M.T.
PLEASE NOTE:
1) FOR SAFE OPERATION AND CONTINUED
HIGH PERFORMANCE FROM THIS
EQUIPMENT, INSPECTION AND
MAINTENANCE MUST BE PERFORMED
BEFORE EACH USE.
2) USE OF THIS EQUIPMENT OTHER THAN
INTENDED MAY BE HAZARDOUS.
3) ALTERATION OR MODIFICATION OF
EQUIPMENT MAY BE HAZARDOUS.
FOR REPAIR OR REPLACEMENT, PLEASE
CALL YOUR DEALER.
DETAIL A-A
DATE:
7A, 7B, 7C OR 7D
9"
78"
CTR TO CTR
78"
CTR TO CTR
78"
CTR TO CTR
9"
21'-0"
9"
81"
CTR TO CTR
81"
CTR TO CTR
9"
9"
78"
CTR TO CTR
9"
9"
76 1/2"
CTR TO CTR
76 1/2"
CTR TO CTR
76 1/2"
CTR TO CTR
76 1/2"
CTR TO CTR
9"
27'-0"
15'-0"
8'-0"
PBS-90
PBS-10
PBS-20
PBS-80
OPTIONAL ANCHOR
SEE *NOTE

Rev-B 6/5/19
JAYPRO SPORTS
PLAYER BENCH WITH SHELF PBS-10/PBS-20/PBS-80/PBS-90
LIST OF MATERIALS
PIECE #
PART #
DESCRIPTION
PBS-
10
PBS-
20
PBS-
80
PBS-
90
1
AR5044
BOLT CLIP
32
24
16
40
2
AR5045A
END CAP
8
8
8
8
3
HB5030
5/16”-18 x 3” CARRIAGE BOLT
32
24
16
40
4
HN5046
5/16” FLANGE NUT
32
24
16
40
5
HS5035
#8 ZP PAN HEAD SCREW x ½”
16
16
16
16
6
EP0018
2” x 2” END PLUG
16
12
8
20
7A
AR5111
27’ PLANK
N/A
N/A
N/A
4
7B
AR5052
21’ PLANK
4
N/A
N/A
N/A
7C
AR5053
15’ PLANK
N/A
4
N/A
N/A
7D
AR5079
7.5’ PLANK
N/A
N/A
4
N/A
8
PBS-L
LEG FRAME
4
3
2
5
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED: Phillips Screwdriver Bit With Electric Drill (1),
½” Socket Wrench or Adjustable Wrench (1)
1) Slip the end caps (2) snugly onto each end of each plank (7). Using the electric drill,
assemble a self-drilling screw (5) through the cap and into the flange of the plank. Two
screws are required per end cap. Carefully assemble 2” end caps (6) into bench legs (8).
2) For easiest assembly, position the shelf planks (7) on a flat level surface. Place the
carriage bolt (3) and bolt clips (1) approximately into place within the slots of the plank.
Note that the outside legs should be no more than 8” from the plank edge or 9” from edge
to center of leg.
3) Position the legs (8) as shown and loosely assemble the hardware illustrated in detail ‘A-
A’. Do not fully tighten the hardware at this time.
4) Stand the unit upright and assemble the seat plank and backrest plank (7) as illustrated.
Level the bench and make sure the legs are correctively spaced apart. Tighten all
fasteners fully.
*Note: To anchor bench to a concrete base drill 2X 7/16” holes in each leg frame as shown.
After assembled, anchor bench to concrete using a suitable concrete anchor (not supplied).