Jaypro Sports SEYL-824 Specification sheet

DETAIL A
DETAIL B
DETAIL C
(PIN DETAIL)
DETAIL D
(TYP PIPE TO PIPE CONNECTION)
976 Hartford Turnpike
Waterford, CT 06385 USA
(800)243−0533 Fax: (800)988−3363
www.jaypro.com DATE: DRAWN BY:
7/7/2009
MODEL NUMBER: CHECKED BY:
PRODUCT NAME:
Moune T.
SEYL-824
QUICK SET-UP SOCCER GOAL
WVB
PAGE:
1 OF 2
LEFT UPRIGHTSEYL-LW11
RIGHT UPRIGHTSEYL-RW
12
BASE FRAMESEYL-A23
BACKSTAY EXTENSION TUBESEYL-FA22
4
REAR BACKSTAYSEYL-EA2
25
MIDDLE CROSSBARSEYL-D16
END CROSSBARSEYL-C
27
SNAP BUTTON
HM505188
DESCRIPTIONPART #QTYITEM
7/16" x 2 1/2" QUICK RELEASE PIN w/ LANYARDHM623929
#10-16 x 5/16" THREAD FORM SCREW, SSHS1233
210
3/8"-16 NYLON JAM NUT, SSHN1230411
3/8"-16 x 2 3/4" BUTTON HD HEX SCREW, SSHS5163
4
12
NET STAKE 1/4" x 9"
HM41041013
3/4" WIDE WHITE ONE WRAP x 4 YDNW0047114
1 1/2" x 24" INDOOR ANTI-SKID PADS
RR5023815
NET (NOT INCLUDED)SEYL-24NHP
116
DESCRIPTIONPART #QTYITEM
D
B
C
A
E
F
G
5
5
1
7
6
7
11
5
12
1 OR 2
1 OR 2
3
11
12
8
4
5
8
10
3
8VARIES VARIES
9

FIGURE: 1
FIGURE: 2
DETAIL F
(TYP NET ATTACHMENT)
DETAIL E
(OPTIONAL INDOOR FEET)
DETAIL G
976 Hartford Turnpike
Waterford, CT 06385 USA
(800)243−0533 Fax: (800)988−3363
www.jaypro.com DATE: DRAWN BY:
7/7/2009
MODEL NUMBER: CHECKED BY:
PRODUCT NAME:
Moune T.
SEYL-824
QUICK SET-UP SOCCER GOAL
WVB
PAGE:
2 OF 2
DISCONNECT PIN (ITEM 9)
RE-INSERT PIN (ITEM 9)
TELESCOPE PIPE INTO ITEM 5
14
1 OR 2
15
APPROXIMATELY SPACED 15" APART
3
NET
13
NET
5
4
3
1 OR 2

Rev E, 07/09
JAYPRO SPORTS
SEYL-824, QUICK SET-UP SOCCER GOAL
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) SECURELY ANCHOR (USING GROUND STAKES OR SAND BAGS)
MOVEABLE SOCCER GOALS AT ALL TIMES (ANCHORS PURCHASED
SEPARATELY).
3) NEVER ALLOW ANYONE TO CLIMB ON THE NET OR GOAL FRAME.
4) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
5) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
(1) 9/16” Socket or Box Wrench
(1) 7/32 Allen Wrench
(1) Phillips Head Screwdriver
(1) Unpack all parts and check against parts list to ensure that all have been included.
(2) Inspect all parts for damage. Report any damages to the trucking company.
(3) Identify all frame components and lay them out on a flat dry surface. The goal should
be assembled face down.
(4) Assemble the top crossbar (items 6 and 7) as shown in (Detail D). Locate corner of
net and weave crossbar through leading edge (note: there is no specific top or bottom
to net as net is symmetric).
(5) Attach both left and right uprights (items 1 and 2) to each end of crossbar.
(6) Attach the lanyard plate of Quick Release Pin (item 9) to the back end of each base
frame (item 3), using the thread forming screws supplied (item 10). (Note: use
predrilled hole located in front of U-bracket - see Detail C)
(7) Attach the front end of base frame (item 3) to base of upright using hardware shown
in Detail B. (Note: front end of base frame has rounded corners). For best results lay
base frame overtop of upright.
For indoor use, apply adhesive backed rubber anti-skid pads to underside of
base frame – using scissors, cut pads in 3” lengths - four per side, equally spaced.
(See Detail E)

Rev E, 07/09
(8) Attach rear backstay (item 5) to upright using hardware shown in Detail A.
(9) Insert one backstay extension tube (item 4) into each rear backstay. (Note: insert end
with single hole and snap pin, see Detail C).
(10) Lift rear backstay and raise base frame into vertical position. Assemble rear backstay
into base frame by inserting quick release pin. (See Detail C)
(11) Stand goal upright using at least two people.
(12) Pull the net from each end to stretch over top crossbar. Drape net over both
backstays. Secure front edge of net to upright using 9” lengths of velcro net tie.
Secure net to backstay using 9” lengths of velcro net ties. (See Detail F)
(13) Anchor base of net using ground stakes provided. (See Detail G)
STORAGE INSTRUCTIONS
(SEYL-24GCB, Storage Bag provided separately)
(1) Using no less than two people, lower the goal face down onto the ground. Remove
quick release pin (item 9) and lower the base frame onto the upright pipe. Re-insert
the quick release pin (item 9) back into its original position.
(2) Telescope the backstay extension tube (item 4) into the rear backstay (item 5). The
rear backstay will fold onto the base frame.
(3) Disassemble both uprights from the crossbar.
(4) Remove net from the crossbar and disassemble the crossbar.