jbc P-405 User manual

INSTRUCTION MANUAL
www.jbctools.com
Ref. P-405
Pedal

Optional: To another module
Required: To DME, DDE, HDE Control unit or module
Pedal
Ref. P-405
Compatible modules
Ref. MSE, MVE, MNE
NAE Control Unit
Ref. NAE
www.jbctools.com
2
Packing List
The followwing items are included:
Pedal ............................................1 unit
Ref. P-405
Manual .......................... 1 unit
Ref. 0023904
Pedal
Ref. P-405
Installation for MSE, MVE, MNE and NAE Control Units
INSTRUCTION MANUAL

www.jbctools.com
3
Installation for JTSE-UA Hot Air Control Unit
Hot Air control unit
Ref. JTSE-UA Pedal
Ref. P-405
Press the pedal to start blowing hot air and release to stop.
IR Preheater
Ref. PHSE-KA
Press the pedal to start heating and press again to stop as if it was the button on the console.
Installation for PHSE/PHBE IR Preheater
Pedal
Ref. P-405

4
1. Enter the Peripherals Menu and join the pedal (PD) to the appropriate port.
Peripherals are
displayed according
to the order when
connected
Initial Set up for DME Control Unit
Switch between
Sleep and work mode
Switch between
Hibernation and
work mode
The pedal controls
the module
Select the activation
of the pedal (either
pressing or releasing)
Set the duration
of the activation
time when pressing
the pedal once*.
For continuous
functioning keep the
pedal pressed.
*NB: The same can be applied inversely when continually pressing the pedal and releasing to activate.
17:14 ?
Peripherals
Sleep
Extractor
Module
Ok
Press to select the port
17:14 ?
Peripherals
Activation released
Minimum time 0 sec
Ok
17:14 ?
Peripherals
PD Port 4
MSE Port 1
2. Select the pedal function according to your needs.
3. Set the features of the function you have chosen.

www.jbctools.com
5
1. Enter the Peripherals Menu and select the port which you want to join to the pedal.
2. Select the pedal from the list.
Select how the pedal
acts: as Sleep,
Extractor (hibernation)
or as a module switch.
Select the activating
mode of the pedal
(pressed/released)
Initial Set up for DDE, HDE, NAE, JTSE or
PHSE/PHBE Control Units
Select port
Note that your first
connection is denoted
as “a”, the second
being “b”, etc. (e.g.
PD_ a, PD_ b,...)
Peripherals Port 2-PA
17:14
Pedal PD_a
Function Extractor
Mode released
Minimum time 0 sec
Back
Peripherals Port 2-PA
17:14
Pedal PD_a
Module MSE
Pedal
PD_a
PD_b
None
Peripherals Port 2-PA
17:14
Pedal PD_a
Module MSE
Set the duration
of the activation
time when pressing
the pedal once*.
For continuous
functioning keep the
pedal pressed.
*NB: The same can be applied inversely when continually pressing the pedal and releasing to activate.
3. Set the pedal function according to your work needs:

2
1
6
Operation with tweezers
The Pedal is frequently used to rework components with tweezers, thereby causing no thermal
stress to the component until the solder joint is made.
Clean the pads with the desoldering tool
DS360-A*.
* Secondary station is needed.
Apply the solder paste amount needed to
solder the new chip component.
Pad cleaning
Solder paste dispensing

4
3
www.jbctools.com
7
Press and hold the pedal and use the
tool to position the component on the
previously tinned pads.
Placing
Soldering
Once in position, press and hold the
pedal to perform the soldering.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
www.jbctools.com
- Weight: 410 g (14.4 oz)
- Dimensions: 100 x 200 x 40 mm
- Cable length: 1.9 m
Complies with CE standards
ESD safe
Specifications
0023904-0620