JBL AM7200/95-WH User manual

JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
JBL AM7200/95-WH
REV C
PACKAGE WIRING DIAGRAM
01-11
Technical Manual
JBL AM7200/95-WH
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• Nominal Impedance: 8 Ohms
• Transducer Power Rating: MF: 350W (1400W peak), 2 hrs
(AES) HF: 100W (400W peak), 2 hrs
• Long-Term System Power
Rating (IEC): MF/HF: 200W (800W peak),100 hrs
• Frequency Response: 330 Hz - 18 kHz (±3 dB)
• Frequency Range: 260 Hz - 20 kHz (-10 dB)
• Maximum SPL:
Bi-amp mode: MF: 133 dB-SPL cont avg (139 dB peak)
HF: 133 dB-SPL cont avg (139 dB peak)
Passive mode: MF/HF: 133 dB-SPL cont avg (139 db
peak)
• System Sensitivity:
Passive mode: 108 dB SPL
1 watt @ 1 meter
• Crossover Frequency: 2.2 kHz
SYSTEM COMPONENTS:
• Cabinet: Enclosure (Not For Sale)
• Grille: 338163-009, 338163-109 (WH)
• Midrange Driver: JBL CMCD-82H,Cone Compression
SYSTEM COMPONENTS: (CONT’D)
Driver with integral 200 mm (8 in)
Differential Drive® dual voice-coil
internal driver
• DC Resistance: 5.1 ohm +/-10%
• High Frequency 2432H, 38 mm (1.5 in) exit
Transducer: compression driver,75 mm (3 in)
voice coil
• DC Resistance: 4.00 ohm +/- 0.2 ohm
• Crossover Network: 445298-001
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 7.0V Input, 200 Hz to 10 kHz
Sweep Duration: 5 seconds
B. M.F. Aural Sweep Test: 7.0V Input, 20 Hz to 1 kHz
C. H.F. Aural Sweep Test: 3.0V Input, 300 Hz to 1.0 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 548 x 561 x 657 mm D
(21.6 x 22.1 x 25.9 in.D.)
• Net Weight: 60 lb (27.2 kg.)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
SEE NETWORK SCHEMATIC PAGE
NOTE: INDIVIDUAL PARTS FOR THE ABOVE CROSSOVER ARE NOT AVAILABLE.
A COMPLETE REPLACEMENT ASSEMBLY SHOULD BE ORDERED.
Logo Sticker
339399-001
Poly Bag
350691-001
Warranty Card
59660
Installation Data
Sheet
339390-075
Bag
21784
Carton
338862-001
Filler (2)
351590-001
PKG, Microfoam (8)
49790P
20” x 18” Sheets
Network Assembly
445298-001
Driver, Mid Freq.
2169H
(339111-001X)
Cone Repl
C8R2169
Driver, High Freq.
2432H
(365512-001X)
Diaph Repl
D8R2432
WHT/BLK WHT
YEL/BLK
YEL

SCHEMATIC (445298-001) JBL AM7200/95-WH
JBL AM7200/95-WH
Individual Parts for the above crossover are not available.
A complete replacement assembly should be ordered.
0.91mH 0.91mH 0.47mH
0.27mH 0.62mH
13uF
250V 9.1uF
250V
3.65uF
250V 2% 6.8uF
250V
WHT/BLK
WHT
WHT
RED
BLK
YEL
YEL/BLK
YEL + 0.187
- 0.250
Connector, 8-PIN
Molex P/N 39-01-2080
-
+

COMPONENT EXPLODEDVIEW JBL AM7200/95-WH
JBL AM7200/95-WH
Grille Assembly
338163-009
338163-109 (WH)
Screw (8)
882-51110-12
882-51160-12 (WH)
6 x 3/4
OV,PH,PTCL,
ZINC,LCS
Horn
444879-001
Screw (16)
804-41110-12
10-32 x 3/4
PAN,PH,BLK
ZINC,LCS
Nut (4)
834-30010-00
1/4-20
KEPS,BLK
ZINC,LCS, RIGHT
Stud (4)
75815
1/4-20 x 1.5”LG
Driver, High Freq.
2432H
(365512-001X)
Diaph Repl
D8R2432
Driver, Mid
Freq.
2169H
(339111-001X)
Cone Repl
C8R2169
Screw (4)
804-41110-12
10-32 x 3/4
PAN,PH,BLK
ZINC,LCS
Dome
31385-05
Gasket
350307-001
Phasing Plug
338471-001
Screw (4)
874-33114-18
10-32 x 1 1/4
CAP HEX
Washer (4)
843-00110-06
10x.06
FLT PL, BLK
Gasket
339403-001
Screen
339484-001
Screw (4)
874-33114-18
10-32 x 1 1/4
CAP HEX
Washer (4)
843-00110-06
#10x.06
FLT,PL,BLK
Logo, Grille
339400-001
Push Nut
350689-001
Compression Spring
365201-001
Washer
76168
BLK.175ID .750D
Grille Support (2)
338380-001 Network Assembly
445298-001
Screw (5)
882-41110-10
6 x 5/8
PAN,PH,PB,
BLK ZINC,LCS
T-Nut (16)
61861
10-32
Mounting Support (6)
381-00023-01
90 Degrees 2X M10
(internal)
Screw (12)
883-41110-08
8 x 1/2
PAN,PH,BLK ZINC
LCS
Bolt (13)
352051-001
352051-002 (WH)
M20 x 25MM
HEX
Mounting Bracket
338652-001
Flat Single M10
(internal)
Screw (2)
883-41110-08
8 x 1/2
PAN,PH,PB
BLK ZINC,LCS
Input Plate
339336-001
Screw (6)
882-41110-10
6 x 5/8
PAN,PH,PB
BLK ZINC,LCS
Input Plate Label (HADM)
440926-008
Label
339339-082
339339-182 (WH)
Enclosure Assembly
AM7200/95-WH
(not available for sale)