JDS Uniphase CellAdvisor JD700B Series User manual

Network and Service Enablement
One Milestone Center Court
Germantown, Maryland 20876-7100 USA
Toll Free 1-855-ASK-JDSU • Tel [phone] • Fax [phone]
www.jdsu.com
Product Name/Family Brand
Attribute/Descriptor
Type of Manual
CellAdvisor JD700B Series
User’s Guide
JD785B/JD745B Base Station Analyzer
JD786B/JD746B RF Analyzer
JD788B/JD748B Signal Analyzer

Network and Service Enablement
One Milestone Center Court
Germantown, Maryland 20876-7100 USA
Toll Free 1-855-ASK-JDSU • Tel [phone] • Fax [phone]
www.jdsu.com
CellAdvisor JD700B Series
User’s Guide
JD785B/JD745B Base Station Analyzer
JD786B/JD746B RF Analyzer
JD788B/JD748B Signal Analyzer

JD700B Series User’s Guide
Notice
Every effort was made to ensure that the information in this document was
accurate at the time of release. However, information is subject to change without
notice, and JDS Uniphase reserves the right to provide an addendum to this
document with information not available at the time that this document was
created.
Copyright
© Copyright 2014 JDS Uniphase Corporation. All rights reserved. JDSU, Network
and Service Enablement, and its logo are trademarks of JDS Uniphase
Corporation (“JDS Uniphase”). All other trademarks and registered trademarks are
the property of their respective owners. No part of this document may be
reproduced or transmitted electronically or otherwise without written permission of
the publisher.
Copyright release
Reproduction and distribution of this document is authorized for Government
purposes only.
Trademarks
JDSU and CellAdvisor are trademarks or registered trademarks of JDSU in the
United States and/or other countries.
Google Maps and Google Earth are either trademarks or registered trademarks of
Google in the United States and/or other countries.
Bluetooth is a trademark or a registered trademark of Bluetooth Special Interest
Group (SIG) Inc. in the United States and/or other countries.
Android is a trademark or a registered trademark of Google in the United States
and/or other countries.
iOS is a trademark or a registered trademark of Apple Inc. in the United States
and/or other countries.
Windows and Windows 7 are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Specifications, terms, and conditions are subject to change without notice. All
trademarks and registered trademarks are the property of their respective
companies.
Acknowledgement
This product incorporates open source software entitled “zlib”. The zlib is the
compression library written by Jean-loup Gailly and Mark Adler, who granted
permission to use this software for any purpose, including commercial applications.
This product includes open source software developed by the Apache Software

JD700B Series User’s Guide
Foundation (http://www.apache.org/).
This product used free library for JPEG image compression written and distributed
by Independent JPEG Group or IJG (http://www.ijg.org/).
See “Viewing OSS license” on page 40 for more information.
Ordering information
This document is a product of JDSU, issued as part of the JD700B Series
analyzers. The catalog number for a published manual is JD700B362 - printed.
The catalog number for an electronic manual on CD-ROM is JD700B361 -
electronic.
Terms and conditions
Specifications, terms, and conditions are subject to change without notice. The
provision of hardware, services, and/or software is subject to JDSU’s standard
terms and conditions, available at www.jdsu.com/terms.
NRTL compliance
This product was tested according to UL 61010-1:2012 and CAN/CSA C22.2
No. 61010-1-12. Conformity with these requirements is based upon compliance
with the standard IEC 61010-1. A copy of the Declaration of Conformity is
provided upon your request.
Ce produit a été testé selon la norme UL 61010-1 : 2012 et CAN / CSA C22.2
No. 61010-1-12. La conformité à ces exigences est fondée sur la conformité à la norme
CEI 61010-1. Une copie de la déclaration de conformité est disponible sur demande.
EMC directive compliance
This product was tested and conforms to the EMC Directive, 2004/108/EC and its
amending directives for electromagnetic compatibility. Conformity with this
directive is based upon compliance with the harmonized European standards:
EN61326-1 and CISPR11. A copy of the Declaration of Conformity is provided
upon your request.
Low voltage directive compliance
This product was tested and conforms to the Low Voltage Directive, 2006/95/EC
and its amending directives. Conformity with this directive is based upon
compliance with the harmonized European standard EN61010-1. A copy of the
Declaration of Conformity is provided upon your request.
WEEE and battery directive compliance
JDSU has established processes in compliance with the Waste Electrical and
Electronic Equipment (WEEE) Directive, 2002/96/EC, and the Battery Directive,
2006/66/EC.
This product, and the batteries used to power the product, should not be disposed

JD700B Series User’s Guide
of as unsorted municipal waste and should be collected separately and disposed
of according to your national regulations. In the European Union, all equipment
and batteries purchased from JDSU after 2005-08-13 can be returned for disposal
at the end of its useful life. JDSU will ensure that all waste equipment and
batteries returned are reused, recycled, or disposed of in an environmentally
friendly manner, and in compliance with all applicable national and international
waste legislation.
It is the responsibility of the equipment owner to return equipment and batteries to
JDSU for appropriate disposal. If the equipment or battery was imported by a
reseller whose name or logo is marked on the equipment or battery, then the
owner should return the equipment or battery directly to the reseller.
Instructions for returning waste equipment and batteries to JDSU can be found in
the Environmental section of JDSU’s web site at www.jdsu.com. If you have
questions concerning disposal of your equipment or batteries, contact JDSU’s
WEEE Program Management team at [e-mail].

JD700B Series User’s Guide
Table of Contents
About This Guide .................................................................................................................................. 17
Purpose and scope.......................................................................................................................................................... 18
Assumptions .................................................................................................................................................................... 18
Safety and compliance information .................................................................................................................................. 18
Conventions .................................................................................................................................................................... 19
Technical assistance ........................................................................................................................................................ 20
Chapter 1 JD700B Series Overview ............................................................................................... 22
About the JD700B series ................................................................................................................................................. 23
Features and capabilities ................................................................................................................................................. 23
Options ............................................................................................................................................................................ 24
Specifications .................................................................................................................................................................. 24
AC power ................................................................................................................................................................ 24
Physical specifications ............................................................................................................................................ 24
Chapter 2 Getting Started .............................................................................................................. 25
Unpacking the JD700B series .......................................................................................................................................... 26
Exploring the JD700B series............................................................................................................................................ 26
Front panel ............................................................................................................................................................. 27
Top panel ................................................................................................................................................................ 28
Installing battery pack ...................................................................................................................................................... 31
Starting up the JD700B series ......................................................................................................................................... 31
Managing files ................................................................................................................................................................. 32
Using save .............................................................................................................................................................. 32
Using load .............................................................................................................................................................. 34
Using file manager .................................................................................................................................................. 35
Configuring system .......................................................................................................................................................... 35
Setting frequency reference .................................................................................................................................... 35
Setting date and time .............................................................................................................................................. 35
Setting language ..................................................................................................................................................... 36
Setting power on ..................................................................................................................................................... 36
Changing display mode .......................................................................................................................................... 36
Setting sleep time ................................................................................................................................................... 37
Adjusting LCD brightness ....................................................................................................................................... 37
Adjusting volume .................................................................................................................................................... 37
Upgrading firmware ......................................................................................................................................................... 38
Checking installed firmware version ........................................................................................................................ 38
Installing new firmware ........................................................................................................................................... 38
Managing licenses ........................................................................................................................................................... 39
Checking options .................................................................................................................................................... 39
Installing options ..................................................................................................................................................... 40
Loading temporary license ...................................................................................................................................... 40
Viewing OSS license............................................................................................................................................... 40
Performing service diagnostic .......................................................................................................................................... 40
Viewing system log ................................................................................................................................................. 41
Running self-test ..................................................................................................................................................... 41
Performing factory reset .......................................................................................................................................... 41
Re-aligning touch screen ........................................................................................................................................ 41
Using system administration ............................................................................................................................................ 42
Logging in ............................................................................................................................................................... 42
Changing password ................................................................................................................................................ 42
Locking limit key ..................................................................................................................................................... 42
Running IP test ................................................................................................................................................................ 43

JD700B Series User’s Guide
Activating StrataSync ...................................................................................................................................................... 43
Setting up Internet connection ................................................................................................................................ 43
Establishing a connection to StrataSync ................................................................................................................. 44
StrataSync status indicators .................................................................................................................................... 45
Setting communication .................................................................................................................................................... 45
Configuring Ethernet ............................................................................................................................................... 46
Setting for JDViewer and JDRemote ....................................................................................................................... 46
Setting USBTMC mode ........................................................................................................................................... 46
Setting SCPI mode ................................................................................................................................................. 47
Configuring LMF setting .......................................................................................................................................... 47
Enabling Bluetooth connection ................................................................................................................................ 47
Chapter 3 Analyzing Measurement Results ................................................................................... 48
Using marker ................................................................................................................................................................... 49
Using peak search ........................................................................................................................................................... 50
Chapter 4 Using Spectrum Analyzer .............................................................................................. 51
Introduction ..................................................................................................................................................................... 52
Display overview ............................................................................................................................................................. 52
Connecting a cable .......................................................................................................................................................... 53
Selecting measurement mode ......................................................................................................................................... 54
Configuring test parameters ............................................................................................................................................ 54
Setting frequency .................................................................................................................................................... 54
Setting amplitude .................................................................................................................................................... 56
Setting bandwidth ................................................................................................................................................... 58
Setting average ...................................................................................................................................................... 59
Setting sweep ......................................................................................................................................................... 59
Using RF source ..................................................................................................................................................... 61
Conducting spectrum measurements .............................................................................................................................. 61
Setting trace ........................................................................................................................................................... 62
Setting limit ............................................................................................................................................................. 63
Conducting RF measurements ........................................................................................................................................ 64
Channel power ....................................................................................................................................................... 64
Occupied bandwidth ............................................................................................................................................... 65
Spectrum emission mask (SEM) ............................................................................................................................. 67
Adjacent channel power (ACP) ............................................................................................................................... 69
Multi-ACP ............................................................................................................................................................... 70
Spurious emissions ................................................................................................................................................. 72
AM/FM audio demodulation .................................................................................................................................... 74
Field strength meter ................................................................................................................................................ 76
Route map .............................................................................................................................................................. 78
Dual spectrum ........................................................................................................................................................ 80
PIM detection (single and multiple carriers) ............................................................................................................. 81
Chapter 5 Using Interference Analyzer .......................................................................................... 83
Introduction ..................................................................................................................................................................... 84
Display overview ............................................................................................................................................................. 84
Connecting a cable .......................................................................................................................................................... 85
Selecting measurement mode ......................................................................................................................................... 86
Configuring test parameters ............................................................................................................................................ 86
Setting frequency .................................................................................................................................................... 86
Setting amplitude .................................................................................................................................................... 87
Setting bandwidth ................................................................................................................................................... 89
Setting average ...................................................................................................................................................... 90
Setting sweep ......................................................................................................................................................... 90
Conducting spectrum measurements .............................................................................................................................. 92
Setting trace ........................................................................................................................................................... 92
Sound indicator ....................................................................................................................................................... 93
AM/FM audio demodulation .................................................................................................................................... 93
Interference ID ........................................................................................................................................................ 94
Conducting interference measurements .......................................................................................................................... 94
Spectrogram ........................................................................................................................................................... 94
Dual spectrogram ................................................................................................................................................... 96
RSSI ....................................................................................................................................................................... 97
Interference finder ................................................................................................................................................... 98

JD700B Series User’s Guide
Spectrum Replayer ............................................................................................................................................... 100
Setting limit for interference analyzer ............................................................................................................................. 101
Chapter 6 Using GSM/GPRS/EDGE Signal Analyzer .................................................................. 103
Introduction ................................................................................................................................................................... 104
Display overview ........................................................................................................................................................... 104
Connecting a cable ........................................................................................................................................................ 105
Direct connection .................................................................................................................................................. 105
Indirect connection ................................................................................................................................................ 105
Over the air (OTA) ................................................................................................................................................ 106
Selecting measurement mode ....................................................................................................................................... 107
Configuring test parameters .......................................................................................................................................... 107
Setting frequency .................................................................................................................................................. 107
Setting amplitude .................................................................................................................................................. 108
Setting average .................................................................................................................................................... 110
Setting sweep mode ............................................................................................................................................. 110
Setting trigger source ............................................................................................................................................ 110
Conducting spectrum measurements .............................................................................................................................111
Setting measure setup ...........................................................................................................................................111
Setting trace ..........................................................................................................................................................111
Conducting RF measurements ...................................................................................................................................... 112
Channel power ..................................................................................................................................................... 112
Occupied bandwidth ............................................................................................................................................. 113
Spectrum emission mask (SEM) ........................................................................................................................... 114
Spurious emissions ............................................................................................................................................... 115
Setting limit for RF tests ........................................................................................................................................ 117
Conducting power vs. time measurements .................................................................................................................... 118
Power vs. time (slot) ............................................................................................................................................. 118
Power vs. time (frame) .......................................................................................................................................... 119
Conducting constellation measurements ....................................................................................................................... 121
Setting measure setup .......................................................................................................................................... 121
Setting limit for constellation ................................................................................................................................. 121
Measurement example ......................................................................................................................................... 122
Performing auto measurements ..................................................................................................................................... 123
Setting limit for auto measure ............................................................................................................................... 123
Setting measure setup .......................................................................................................................................... 123
Setting display ...................................................................................................................................................... 124
Conducting GSM OTA measurements ........................................................................................................................... 124
Channel scanner................................................................................................................................................... 124
Frequency scanner ............................................................................................................................................... 126
Multipath profile .................................................................................................................................................... 127
Modulation analyzer .............................................................................................................................................. 128
Chapter 7 Using WCDMA/HSPA+ Signal Analyzer ...................................................................... 130
Introduction ................................................................................................................................................................... 131
Display overview ........................................................................................................................................................... 131
Connecting a cable ........................................................................................................................................................ 132
Direct connection .................................................................................................................................................. 132
Indirect connection ................................................................................................................................................ 132
Over the air (OTA) ................................................................................................................................................ 133
Selecting measurement mode ....................................................................................................................................... 134
Configuring test parameters .......................................................................................................................................... 134
Setting frequency .................................................................................................................................................. 134
Setting amplitude .................................................................................................................................................. 135
Setting average .................................................................................................................................................... 137
Setting sweep mode ............................................................................................................................................. 137
Setting trigger source ............................................................................................................................................ 137
Setting external clock ............................................................................................................................................ 137
Conducting spectrum measurements ............................................................................................................................ 139
Setting trace ......................................................................................................................................................... 139
Conducting RF measurements ...................................................................................................................................... 140
Channel power ..................................................................................................................................................... 140
Occupied bandwidth ............................................................................................................................................. 141
Spectrum emission mask (SEM) ........................................................................................................................... 142
ACLR .................................................................................................................................................................... 143

JD700B Series User’s Guide
Multi-ACLR ........................................................................................................................................................... 144
Spurious emissions ............................................................................................................................................... 145
Setting limit for RF tests ........................................................................................................................................ 147
Conducting modulation measurements .......................................................................................................................... 147
Constellation ......................................................................................................................................................... 147
Code domain power .............................................................................................................................................. 148
Relative code domain power ................................................................................................................................. 151
Codogram ............................................................................................................................................................. 153
RCSI ..................................................................................................................................................................... 155
CDP Table ............................................................................................................................................................ 157
Setting limit for modulation tests ........................................................................................................................... 158
Performing auto measurements ..................................................................................................................................... 159
Setting limit for auto measure ............................................................................................................................... 159
Setting measure setup .......................................................................................................................................... 159
Setting display ...................................................................................................................................................... 160
Performing power statistics CCDF measurement .......................................................................................................... 160
Setting measure setup .......................................................................................................................................... 161
Measurement example ......................................................................................................................................... 161
Conducting WCDMA/HSPA+ OTA measurements ......................................................................................................... 161
Channel scanner................................................................................................................................................... 162
Scramble scanner ................................................................................................................................................. 163
Multipath profile .................................................................................................................................................... 164
Code domain power .............................................................................................................................................. 165
Route map ............................................................................................................................................................ 166
Chapter 8 Using LTE - FDD Signal Analyzer ................................................................................ 169
Introduction ................................................................................................................................................................... 170
Display overview ........................................................................................................................................................... 171
Connecting a cable ........................................................................................................................................................ 171
Direct connection .................................................................................................................................................. 171
Indirect connection ................................................................................................................................................ 172
Over the air (OTA) ................................................................................................................................................ 172
Selecting measurement mode ....................................................................................................................................... 173
Configuring test parameters .......................................................................................................................................... 174
Setting frequency .................................................................................................................................................. 174
Setting amplitude .................................................................................................................................................. 174
Setting average .................................................................................................................................................... 176
Setting sweep mode ............................................................................................................................................. 177
Setting trigger source ............................................................................................................................................ 177
Setting external clock ............................................................................................................................................ 177
Conducting spectrum measurements ............................................................................................................................ 178
Setting measure setup .......................................................................................................................................... 178
Setting trace ......................................................................................................................................................... 179
Conducting RF measurements ...................................................................................................................................... 179
Channel power ..................................................................................................................................................... 179
Occupied bandwidth ............................................................................................................................................. 180
Spectrum emission mask (SEM) ........................................................................................................................... 181
ACLR .................................................................................................................................................................... 182
Multi-ACLR ........................................................................................................................................................... 183
Spurious emissions ............................................................................................................................................... 184
Setting limit for RF tests ........................................................................................................................................ 186
Conducting power vs. time (frame) measurements ........................................................................................................ 187
Setting measure setup .......................................................................................................................................... 187
Measurement example ......................................................................................................................................... 188
Conducting modulation measurements .......................................................................................................................... 188
Constellation ......................................................................................................................................................... 188
Data channel ........................................................................................................................................................ 190
Control channel .................................................................................................................................................... 193
Subframe .............................................................................................................................................................. 196
Frame ................................................................................................................................................................... 199
Time alignment error ............................................................................................................................................. 202
Data allocation map .............................................................................................................................................. 203
Setting limit for modulation tests ........................................................................................................................... 206
Performing auto measurements ..................................................................................................................................... 207
Conformance test ................................................................................................................................................. 207
Maintenance test .................................................................................................................................................. 209

JD700B Series User’s Guide
Signal performance test ........................................................................................................................................ 211
DAS test ............................................................................................................................................................... 212
Performing power statistics CCDF measurements ......................................................................................................... 213
Setting measure setup .......................................................................................................................................... 213
Measurement example ......................................................................................................................................... 214
Performing carrier aggregation measurements .............................................................................................................. 214
Setting measure setup .......................................................................................................................................... 214
Setting display ...................................................................................................................................................... 215
Measurement example ......................................................................................................................................... 216
Using marker ........................................................................................................................................................ 216
Conducting LTE - FDD OTA measurements ................................................................................................................... 217
Channel scanner................................................................................................................................................... 217
ID scanner ............................................................................................................................................................ 218
Multipath profile .................................................................................................................................................... 220
Control channel .................................................................................................................................................... 221
Datagram .............................................................................................................................................................. 223
Route map ............................................................................................................................................................ 225
Chapter 9 Using LTE - TDD Signal Analyzer ................................................................................ 230
Introduction ................................................................................................................................................................... 231
Display overview ........................................................................................................................................................... 232
Connecting a cable ........................................................................................................................................................ 232
Direct connection .................................................................................................................................................. 232
Indirect connection ................................................................................................................................................ 233
Over the air (OTA) ................................................................................................................................................ 233
Selecting measurement mode ....................................................................................................................................... 234
Configuring test parameters .......................................................................................................................................... 235
Setting frequency .................................................................................................................................................. 235
Setting amplitude .................................................................................................................................................. 235
Setting average .................................................................................................................................................... 237
Setting sweep mode ............................................................................................................................................. 237
Setting trigger source ............................................................................................................................................ 238
Setting external clock ............................................................................................................................................ 238
Conducting spectrum measurements ............................................................................................................................ 239
Setting measure setup .......................................................................................................................................... 239
Setting trace ......................................................................................................................................................... 240
Conducting RF measurements ...................................................................................................................................... 241
Channel power ..................................................................................................................................................... 241
Occupied bandwidth ............................................................................................................................................. 242
Spectrum emission mask (SEM) ........................................................................................................................... 243
ACLR .................................................................................................................................................................... 244
Multi-ACLR ........................................................................................................................................................... 245
Spurious emissions ............................................................................................................................................... 247
Setting limit for RF tests ........................................................................................................................................ 248
Conducting power vs. time measurements .................................................................................................................... 249
Power vs. time (slot) ............................................................................................................................................. 249
Power vs. time (frame) .......................................................................................................................................... 251
Conducting modulation measurements .......................................................................................................................... 252
Constellation ......................................................................................................................................................... 252
Data channel ........................................................................................................................................................ 255
Control channel .................................................................................................................................................... 258
Subframe .............................................................................................................................................................. 261
Time alignment error ............................................................................................................................................. 264
Data allocation map .............................................................................................................................................. 266
Setting limit for modulation tests ........................................................................................................................... 268
Performing auto measurements ..................................................................................................................................... 270
Conformance test ................................................................................................................................................. 270
Maintenance test .................................................................................................................................................. 271
Signal performance test ........................................................................................................................................ 274
DAS test ............................................................................................................................................................... 275
Performing power statistics CCDF measurements ......................................................................................................... 276
Setting measure setup .......................................................................................................................................... 276
Measurement example ......................................................................................................................................... 277
Performing carrier aggregation measurements .............................................................................................................. 277
Setting measure setup .......................................................................................................................................... 277
Setting display ...................................................................................................................................................... 278

JD700B Series User’s Guide
Measurement example ......................................................................................................................................... 279
Using marker ........................................................................................................................................................ 279
Conducting LTE - TDD OTA measurements ................................................................................................................... 280
Channel scanner................................................................................................................................................... 280
ID scanner ............................................................................................................................................................ 281
Multipath profile .................................................................................................................................................... 283
Control channel .................................................................................................................................................... 284
Datagram .............................................................................................................................................................. 286
Route map ............................................................................................................................................................ 288
Chapter 10 Using CDMA Signal Analyzer ...................................................................................... 293
Introduction ................................................................................................................................................................... 294
Display overview ........................................................................................................................................................... 295
Connecting a cable ........................................................................................................................................................ 295
Direct connection .................................................................................................................................................. 295
Indirect connection ................................................................................................................................................ 296
Over the air (OTA) ................................................................................................................................................ 296
Selecting measurement mode ....................................................................................................................................... 297
Configuring test parameters .......................................................................................................................................... 297
Setting frequency .................................................................................................................................................. 297
Setting amplitude .................................................................................................................................................. 298
Setting average .................................................................................................................................................... 300
Setting sweep mode ............................................................................................................................................. 300
Setting trigger source ............................................................................................................................................ 301
Setting external clock ............................................................................................................................................ 301
Conducting spectrum measurements ............................................................................................................................ 302
Setting trace ......................................................................................................................................................... 303
Conducting RF measurements ...................................................................................................................................... 304
Channel power ..................................................................................................................................................... 304
Occupied bandwidth ............................................................................................................................................. 304
Spectrum emission mask (SEM) ........................................................................................................................... 305
ACPR ................................................................................................................................................................... 306
Multi-ACPR ........................................................................................................................................................... 307
Spurious emissions ............................................................................................................................................... 308
Setting limit for RF tests ........................................................................................................................................ 310
Conducting modulation measurements .......................................................................................................................... 310
Constellation ......................................................................................................................................................... 310
Code domain power .............................................................................................................................................. 311
Codogram ............................................................................................................................................................. 313
RCSI ..................................................................................................................................................................... 314
CDP Table ............................................................................................................................................................ 316
Setting limit for modulation tests ........................................................................................................................... 317
Performing auto measurements ..................................................................................................................................... 318
Setting limit for auto measure ............................................................................................................................... 318
Setting measure setup .......................................................................................................................................... 318
Setting display ...................................................................................................................................................... 319
Performing power statistics CCDF measurements ......................................................................................................... 320
Setting measure setup .......................................................................................................................................... 320
Measurement example ......................................................................................................................................... 320
Conducting CDMA OTA measurements ......................................................................................................................... 321
Channel scanner................................................................................................................................................... 321
PN scanner ........................................................................................................................................................... 323
Multipath profile .................................................................................................................................................... 324
Code domain power .............................................................................................................................................. 325
Route map ............................................................................................................................................................ 327
Chapter 11 Using EV-DO Signal Analyzer ..................................................................................... 331
Introduction ................................................................................................................................................................... 332
Display overview ........................................................................................................................................................... 332
Connecting a cable ........................................................................................................................................................ 333
Direct connection .................................................................................................................................................. 333
Indirect connection ................................................................................................................................................ 333
Over the air (OTA) ................................................................................................................................................ 334
Selecting measurement mode ....................................................................................................................................... 335
Configuring test parameters .......................................................................................................................................... 335

JD700B Series User’s Guide
Setting frequency .................................................................................................................................................. 335
Setting amplitude .................................................................................................................................................. 336
Setting average .................................................................................................................................................... 338
Setting sweep mode ............................................................................................................................................. 338
Setting trigger source ............................................................................................................................................ 338
Setting external clock ............................................................................................................................................ 339
Conducting spectrum measurements ............................................................................................................................ 340
Setting trace ......................................................................................................................................................... 340
Conducting RF measurements ...................................................................................................................................... 341
Channel power ..................................................................................................................................................... 341
Occupied bandwidth ............................................................................................................................................. 342
Spectrum emission mask (SEM) ........................................................................................................................... 343
ACPR ................................................................................................................................................................... 343
Multi-ACPR ........................................................................................................................................................... 344
Spurious emissions ............................................................................................................................................... 345
Setting limit for RF tests ........................................................................................................................................ 347
Conducting power vs. time measurements .................................................................................................................... 348
Power vs. time (idle slot) ....................................................................................................................................... 348
Power vs. time (active slot) ................................................................................................................................... 348
Setting limit for power vs. time tests ...................................................................................................................... 349
Conducting modulation measurements .......................................................................................................................... 350
Constellation ......................................................................................................................................................... 350
Code domain power .............................................................................................................................................. 353
MAC Codogram .................................................................................................................................................... 355
RCSI ..................................................................................................................................................................... 356
MAC CDP Table .................................................................................................................................................... 358
Setting limit for modulation tests ........................................................................................................................... 359
Performing auto measurements ..................................................................................................................................... 360
Setting limit for auto measure ............................................................................................................................... 360
Setting measure setup .......................................................................................................................................... 360
Setting display ...................................................................................................................................................... 361
Performing power statistics CCDF measurements ......................................................................................................... 362
Setting measure setup .......................................................................................................................................... 362
Measurement example ......................................................................................................................................... 362
Conducting EV-DO OTA measurements ........................................................................................................................ 362
Channel scanner................................................................................................................................................... 363
PN scanner ........................................................................................................................................................... 364
Multipath profile .................................................................................................................................................... 365
Code domain power .............................................................................................................................................. 366
Route map ............................................................................................................................................................ 368
Chapter 12 Using TD-SCDMA Signal Analyzer .............................................................................. 371
Introduction ................................................................................................................................................................... 372
Display overview ........................................................................................................................................................... 373
Connecting a cable ........................................................................................................................................................ 373
Direct connection .................................................................................................................................................. 373
Indirect connection ................................................................................................................................................ 374
Over the air (OTA) ................................................................................................................................................ 374
Selecting measurement mode ....................................................................................................................................... 375
Configuring test parameters .......................................................................................................................................... 375
Setting frequency .................................................................................................................................................. 375
Setting amplitude .................................................................................................................................................. 376
Setting average .................................................................................................................................................... 378
Setting sweep mode ............................................................................................................................................. 378
Setting trigger source ............................................................................................................................................ 378
Setting external clock ............................................................................................................................................ 379
Conducting spectrum measurements ............................................................................................................................ 379
Setting measure setup .......................................................................................................................................... 379
Setting trace ......................................................................................................................................................... 380
Conducting RF measurements ...................................................................................................................................... 381
Channel power ..................................................................................................................................................... 381
Occupied bandwidth ............................................................................................................................................. 382
Spectrum emission mask (SEM) ........................................................................................................................... 383
ACLR .................................................................................................................................................................... 384
Multi-ACLR ........................................................................................................................................................... 385
Spurious emissions ............................................................................................................................................... 386

JD700B Series User’s Guide
Setting limit for RF tests ........................................................................................................................................ 388
Conducting power vs. time measurements .................................................................................................................... 389
Power vs. time (slot) ............................................................................................................................................. 389
Power vs. time (frame) .......................................................................................................................................... 390
Power vs. time (mask) .......................................................................................................................................... 391
Timogram ............................................................................................................................................................. 393
Setting limit for power vs. time tests ...................................................................................................................... 394
Conducting modulation measurements .......................................................................................................................... 395
Constellation ......................................................................................................................................................... 395
Midamble power ................................................................................................................................................... 397
Code power .......................................................................................................................................................... 398
Code error ............................................................................................................................................................ 399
Setting limit for modulation tests ........................................................................................................................... 401
Performing auto measurements ..................................................................................................................................... 401
Setting limit ........................................................................................................................................................... 402
Setting measure setup .......................................................................................................................................... 402
Setting display ...................................................................................................................................................... 403
Conducting TD-SCDMA OTA measurements ................................................................................................................. 403
Sync-DL ID scanner .............................................................................................................................................. 403
Sync-DL ID vs. Tau ............................................................................................................................................... 404
Sync-DL ID multipath ............................................................................................................................................ 405
Sync-DL ID analyzer ............................................................................................................................................. 406
Route map ............................................................................................................................................................ 407
Chapter 13 Using Mobile WiMAX Signal Analyzer ......................................................................... 410
Introduction ................................................................................................................................................................... 411
Display overview ........................................................................................................................................................... 411
Connecting a cable ........................................................................................................................................................ 412
Direct connection .................................................................................................................................................. 412
Indirect connection ................................................................................................................................................ 412
Over the air (OTA) ................................................................................................................................................ 413
Selecting measurement mode ....................................................................................................................................... 414
Configuring test parameters .......................................................................................................................................... 414
Setting frequency .................................................................................................................................................. 414
Setting amplitude .................................................................................................................................................. 415
Setting average .................................................................................................................................................... 417
Setting sweep mode ............................................................................................................................................. 417
Setting trigger source ............................................................................................................................................ 417
Setting external clock ............................................................................................................................................ 417
Conducting spectrum measurements ............................................................................................................................ 418
Setting measure setup .......................................................................................................................................... 418
Setting trace ......................................................................................................................................................... 419
Conducting RF measurements ...................................................................................................................................... 420
Channel power ..................................................................................................................................................... 420
Occupied bandwidth ............................................................................................................................................. 422
Spectrum emission mask (SEM) ........................................................................................................................... 423
Spurious emissions ............................................................................................................................................... 425
Setting limit for RF tests ........................................................................................................................................ 427
Conducting power vs. time (frame) measurements ........................................................................................................ 427
Setting measure setup .......................................................................................................................................... 427
Setting limit for power vs. time tests ...................................................................................................................... 429
Measurement example ......................................................................................................................................... 429
Conducting modulation measurements .......................................................................................................................... 429
Constellation ......................................................................................................................................................... 429
Spectral flatness ................................................................................................................................................... 431
EVM vs. subcarrier ............................................................................................................................................... 433
EVM vs. symbol .................................................................................................................................................... 434
Setting limit for modulation tests ........................................................................................................................... 436
Performing auto measurements ..................................................................................................................................... 437
Performing power statistics CCDF measurements ......................................................................................................... 438
Setting measure setup .......................................................................................................................................... 438
Measurement example ......................................................................................................................................... 439
Conducting Mobile WiMAX OTA measurements ............................................................................................................ 439
Preamble scanner ................................................................................................................................................. 439
Multipath profile .................................................................................................................................................... 441
Preamble power trend........................................................................................................................................... 442

JD700B Series User’s Guide
Route map ............................................................................................................................................................ 443
Chapter 14 Using Cable and Antenna Analyzer ............................................................................. 446
Introduction ................................................................................................................................................................... 447
Display overview ........................................................................................................................................................... 447
Selecting measurement mode ....................................................................................................................................... 448
Configuring test parameters .......................................................................................................................................... 448
Setting frequency .................................................................................................................................................. 448
Setting distance .................................................................................................................................................... 449
Adjusting scale ..................................................................................................................................................... 449
Setting sweep mode ............................................................................................................................................. 450
Performing calibration .................................................................................................................................................... 450
1-port calibration ................................................................................................................................................... 451
2-port calibration ................................................................................................................................................... 452
Calibration status indicators .................................................................................................................................. 453
Connecting a cable ........................................................................................................................................................ 454
Connecting a cable for reflection, DTF, 1-port phase, and Smith Chart measurements ......................................... 454
Connecting a cable for cable loss (1 port) measurements ..................................................................................... 455
Connecting a cable for 2-port vector measurements ............................................................................................. 455
Connecting a cable for 2-port scalar measurements ............................................................................................. 456
Performing reflection measurements ............................................................................................................................. 457
Making a measurement ........................................................................................................................................ 457
Measurement example ......................................................................................................................................... 458
Performing DTF measurements ..................................................................................................................................... 458
Making a measurement ........................................................................................................................................ 458
Measurement example ......................................................................................................................................... 460
Performing reflection-DTF measurements ..................................................................................................................... 461
Making a measurement ........................................................................................................................................ 461
Measurement example ......................................................................................................................................... 461
Performing cable loss (1 port) measurements ................................................................................................................ 462
Making a measurement ........................................................................................................................................ 462
Measurement example ......................................................................................................................................... 463
Performing 1-port phase measurements ........................................................................................................................ 464
Making a measurement ........................................................................................................................................ 464
Measurement example ......................................................................................................................................... 465
Performing Smith chart measurements .......................................................................................................................... 465
Making a measurement ........................................................................................................................................ 466
Performing 2-port vector measurements ........................................................................................................................ 466
Making a measurement ........................................................................................................................................ 466
Measurement example ......................................................................................................................................... 467
Performing 2-port scalar measurements ........................................................................................................................ 467
Making a measurement ........................................................................................................................................ 468
Measurement example ......................................................................................................................................... 468
Analyzing measurements .............................................................................................................................................. 468
Setting trace and display ....................................................................................................................................... 468
Setting zoom zones .............................................................................................................................................. 469
Setting alternate sweep ........................................................................................................................................ 470
Setting limit for cable and antenna analyzer .......................................................................................................... 470
Chapter 15 Using RFoCPRI Interference Analyzer ........................................................................ 472
Introduction ................................................................................................................................................................... 473
Display overview ........................................................................................................................................................... 473
Connecting a cable ........................................................................................................................................................ 474
In-service testing (monitoring mode) ..................................................................................................................... 474
Out-of-service testing (terminate mode) ................................................................................................................ 474
Selecting measurement mode ....................................................................................................................................... 474
Monitoring layer 2 .......................................................................................................................................................... 475
Selecting measurement mode .............................................................................................................................. 475
Starting layer 2 monitoring .................................................................................................................................... 475
Measurement example ......................................................................................................................................... 476
Performing layer 2 term testing ...................................................................................................................................... 476
Selecting measurement mode .............................................................................................................................. 476
Starting layer 2 term test as master ...................................................................................................................... 476
Starting layer 2 term test as slave ......................................................................................................................... 478
Measurement example ......................................................................................................................................... 478

JD700B Series User’s Guide
Performing interference analysis ................................................................................................................................... 479
Selecting measurement mode .............................................................................................................................. 479
Setting CPRI measure setup ................................................................................................................................. 479
Configuring test parameters .................................................................................................................................. 481
Conducting spectrum measurements .................................................................................................................... 485
Conducting spectrogram ....................................................................................................................................... 487
Conducting RSSI .................................................................................................................................................. 488
Performing spectrum replayer ............................................................................................................................... 490
Setting limit for interference analyzer .................................................................................................................... 491
Performing PIM detection (single and multiple carriers) ................................................................................................. 492
Selecting measurement mode .............................................................................................................................. 492
Calculating possible PIM ....................................................................................................................................... 492
Detecting PIM (single and multiple carriers) .......................................................................................................... 493
Measurement example ......................................................................................................................................... 494
Chapter 16 Using Channel Scanner ............................................................................................... 495
Introduction ................................................................................................................................................................... 496
Display overview ........................................................................................................................................................... 496
Connecting a cable ........................................................................................................................................................ 496
Direct connection .................................................................................................................................................. 496
Indirect connection ................................................................................................................................................ 497
Over the air (OTA) ................................................................................................................................................ 497
Selecting measurement mode ....................................................................................................................................... 498
Configuring test parameters .......................................................................................................................................... 498
Setting frequency .................................................................................................................................................. 498
Setting amplitude .................................................................................................................................................. 498
Setting average .................................................................................................................................................... 500
Setting sweep mode ............................................................................................................................................. 500
Making channel scanner measurements........................................................................................................................ 501
Setting channel ..................................................................................................................................................... 501
Measurement example ......................................................................................................................................... 501
Making frequency scanner measurements .................................................................................................................... 502
Setting frequency .................................................................................................................................................. 502
Measurement example ......................................................................................................................................... 503
Making custom scanner measurements......................................................................................................................... 503
Setting channel/frequency .................................................................................................................................... 503
Measurement example ......................................................................................................................................... 504
Analyzing measurements .............................................................................................................................................. 505
Setting limit for channel scanner ........................................................................................................................... 505
Chapter 17 Using Power Meter ...................................................................................................... 506
Introduction ................................................................................................................................................................... 507
Display overview ........................................................................................................................................................... 507
Performing internal RF power measurements ................................................................................................................ 507
Connecting a cable ............................................................................................................................................... 508
Selecting measurement mode .............................................................................................................................. 508
Setting frequency .................................................................................................................................................. 509
Setting amplitude .................................................................................................................................................. 510
Setting sweep mode ............................................................................................................................................. 510
Making a measurement ........................................................................................................................................ 511
Measurement example ......................................................................................................................................... 511
Performing external RF power measurements ............................................................................................................... 511
Connecting a cable ............................................................................................................................................... 512
Selecting measurement mode .............................................................................................................................. 513
Setting frequency .................................................................................................................................................. 513
Setting amplitude .................................................................................................................................................. 513
Making a measurement ........................................................................................................................................ 514
Measurement example ......................................................................................................................................... 514
Performing optical power measurements ....................................................................................................................... 515
Connecting a cable ............................................................................................................................................... 515
Selecting measurement mode .............................................................................................................................. 515
Setting amplitude .................................................................................................................................................. 516
Making a measurement ........................................................................................................................................ 516
Measurement example ......................................................................................................................................... 517
Setting limit for power meter .......................................................................................................................................... 517

JD700B Series User’s Guide
Chapter 18 Performing Fiber Inspection ........................................................................................ 518
Introduction ................................................................................................................................................................... 519
Display overview ........................................................................................................................................................... 519
Connecting a fiber microscope ...................................................................................................................................... 519
Selecting measurement mode ....................................................................................................................................... 520
Configuring test parameters .......................................................................................................................................... 520
Selecting profile and tip ......................................................................................................................................... 520
Setting preferences ............................................................................................................................................... 520
Performing fiber inspection ............................................................................................................................................ 521
Capturing fiber image............................................................................................................................................ 521
Measurement example ......................................................................................................................................... 522
Testing a fiber ....................................................................................................................................................... 522
Measurement example ......................................................................................................................................... 523
Appendix ............................................................................................................................................. 524
Appendix A – Product general information ..................................................................................................................... 525
JD780B series ...................................................................................................................................................... 525
JD740B series ...................................................................................................................................................... 527
Appendix B – Cable list.................................................................................................................................................. 529
Appendix C – Band, frequency & channel standard ....................................................................................................... 530
Appendix D – VSWR-Return loss conversion table ........................................................................................................ 533
Appendix E – Cyclic prefix table .................................................................................................................................... 534
Appendix F – Motorola CDMA/EV-DO LMF ................................................................................................................... 535
Using JD700B series LMF interface ...................................................................................................................... 535
Setting up for a LMF test ....................................................................................................................................... 535
Performing a LMF test .......................................................................................................................................... 536
Appendix G – Bluetooth connection ............................................................................................................................... 537
Installing and setting up Bluetooth software .......................................................................................................... 537
Making Bluetooth connection ................................................................................................................................ 537
Setting up communication in application ............................................................................................................... 538
Turning Bluetooth mode on/off manually ............................................................................................................... 539
Appendix H – Device driver installation .......................................................................................................................... 540
Appendix I – Ordering information ................................................................................................................................. 541
JD785B Base Station Analyzer ............................................................................................................................. 541
JD786B RF Analyzer ............................................................................................................................................ 542
JD788B Signal Analyzer ....................................................................................................................................... 543
JD745B Base Station Analyzer ............................................................................................................................. 544
JD746B RF Analyzer ............................................................................................................................................ 545
JD748B Signal Analyzer ....................................................................................................................................... 546
JD700B Series Common Options ......................................................................................................................... 547
Appendix J – RoHS information ..................................................................................................................................... 549
JD780B series ...................................................................................................................................................... 549
JD740B series ...................................................................................................................................................... 550
Appendix K – On-screen keyboard ................................................................................................................................ 551
Adding or deleting letters ...................................................................................................................................... 551
Editing or adding a custom keyword ..................................................................................................................... 551
Appending a keyword ........................................................................................................................................... 552

About This Guide
Topics discussed in this chapter include the following:
 Purpose and scope .................................................................................................................... 18
 Assumptions .............................................................................................................................. 18
 Safety and compliance information ........................................................................................... 18
 Conventions ............................................................................................................................... 19
 Technical assistance .................................................................................................................. 20
Sections “Safety and compliance information” and “Conventions” in this chapter contain information in
French as well.

About This Guide
18 JD700B Series User’s Guide
Purpose and scope
The purpose of this guide is to help you successfully operate the JD700B series (firmware version
3.020 and later) and use its features and capabilities. This document includes instructions that
describe how to operate, set up, configure, and use the JD700B series, consisting of JD785B/JD745B
Base Station Analyzer, JD786B/JD746B RF Analyzer, and JD788B/JD748B Signal Analyzer.
Objectif et champ d'application
Le but de ce guide est de vous aider à utiliser avec succès la série JD700B (version du firmware 3.020 et plus
tard) et à utiliser ses fonctions et capacités. Ce document contient des instructions qui décrivent comment utiliser,
créer, configurer et utiliser la série JD700B, composé de JD785B/JD745B Base Station Analyzer,
JD786B/JD746B RF Analyzer, et JD788B/JD748B Signal Analyzer.
Assumptions
This guide is intended for novice, intermediate, and experienced users who want to use the JD700B
series effectively and efficiently. We are assuming that you have basic operation experience and are
familiar with basic mobile communication concepts and terminology.
Hypothèses
Ce guide est destiné aux débutants, intermédiaires et les utilisateurs avancés qui veulent utiliser série JD700B
efficace et efficiente. Nous supposons que vous avez une expérience de base du fonctionnement et êtes familier
avec les concepts de communication mobile et de la terminologie.
Safety and compliance information
It is mandatory to permanently connect this product to the protective earth.
When supplying power to this device, always use an AC power cable that includes an earth (safety)
ground connection.
Informations de sécurité et de conformité
Il est obligatoire de se connecter en permanence ce produit à la protecteur terre. Lorsque alimenter en énergie
cet appareil, utilisez toujours un câble d'alimentation secteur qui comprend une terre de sécurité.
WARNING
Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage and other hazards. Refer all servicing to qualified
service personnel.
AVERTISSEMENT
Ne pas tenter de réparer ce produit vous-même, car l'ouverture ou le retrait des capots peut vous
exposer à des tensions dangereuses et autres risques. Confiez toute réparation à un personnel
qualifié de service JDSU.
CAUTION
This equipment contains parts and assemblies sensitive to electrostatic discharge (ESD).
Use ESD precautionary procedures when touching, removing, or inserting ESD sensitive
parts and assemblies, or damage to components could result.
An electrostatic-sensitive device can only withstand voltage spikes of 10 to 100 volts. Any
discharge greater than this can damage or effectively destroy such a device while going
unnoticed by a technician. Common plastics (synthetic insulating materials), clothing, and
paper or cardboard are the most common source of static charges.
MISE EN GARDE
Cet équipement contient des pièces et des assemblages sensibles aux décharges électrostatiques

About This Guide
JD700B Series User’s Guide 19
(ESD). Utilisez ESD procédures de précaution en cas de contact, la suppression ou l'insertion de
pièces de l'EDD et des assemblages sensibles, ou des dommages aux composants pourraient en
résulter.
Un dispositif électrostatique sensible ne peut supporter des pointes de tension de 10 à 100 volts.
Toute décharge supérieur à ce qui peut endommager ou détruire efficacement un tel dispositif alors
passer inaperçu par un technicien. Matières plastiques (matériaux synthétiques isolants), les
vêtements et le papier ou le carton sont la source la plus fréquente de charges statiques.
CAUTION
This instrument uses a Lithium Ion battery that, if not connected correctly, may lead to
explosion. In case the battery needs to be exchanged, it must be the same kind as or
compatible with the one shipped with your instrument.
The battery must not be disposed of in a landfill site or as municipal waste, and should be
disposed of according to your national regulations.
MISE EN GARDE
Cet instrument utilise une batterie lithium-ion qui, s'il n'est pas connecté correctement, peut conduire
à une explosion. Dans le cas où la batterie a besoin d'être remplacé, il doit être du même type ou
compatible avec celui fourni avec votre instrument.
La batterie ne doit pas être éliminé dans un site d'enfouissement ou les déchets municipaux, et doit
être éliminé conformément à la réglementation nationales.
Conventions
This guide uses typographical and symbols conventions as described in the following tables.
Conventions
Ce guide utilise les conventions typographiques et les symboles tels que décrits dans les tableaux suivants.
Table 1 Text formatting and other typographical conventions
Item
Text formatting/symbols used
Example(s)
Buttons or hard keys that
the user presses on a
physical device
Bold, all caps, default font
Press the ON button.
Press the MODE hard key.
Press the MARKER hard key.
Hot keys that the user
presses on a physical
device
Bold, all caps, italics, default font
Press the SYSTEM hot key.
Press the MEASURE hot key.
Soft keys or toggle keys
that the user presses on a
physical device to select
corresponding menus
Bold, default font
Press the Span soft key.
Press the Channel Power soft key.
Soft key option separators
Denoted by a vertical bar | that
means “or”, only one option can be
selected with a single press
Press the Zone [1|2|3] soft key.
File type
Courier New
In .tra file type.
Required arguments (text
variables in code)
Denoted by slanted brackets < >.
Enter <password>
Table 2 Symbol conventions
This symbol represents a general hazard. It may be associated with either a DANGER,
WARNING, or CAUTION message.
Ce symbole signale la présence d'un danger général.

About This Guide
20 JD700B Series User’s Guide
This symbol represents hazardous voltages. It may be associated with either a
DANGER, WARNING, or CAUTION message.
Ce symbole signale la présence d'un risque d'électrocution.
This symbol represents a risk of explosion. It may be associated with either a DANGER,
WARNING, or CAUTION message.
Ce symbole signale la présence d'un risque d'explosion.
This symbol, located on the equipment, battery, or the packaging indicates that the
equipment or battery must not be disposed of in a landfill site or as municipal waste,
and should be disposed of according to your national regulations.
Ce symbole, situé sur l'équipement, la batterie ou l'emballage indique que l'équipement ou de la
batterie ne doivent pas être jetés dans un site d'enfouissement ou les déchets municipaux, et
doivent être éliminés conformément à la réglementation nationales.
Table 3 Safety definitions
DANGER
DANGER
Indicates a potentially hazardous situation that, if not avoided, will result in
death or serious injury. It may be associated with either a general hazard,
high voltage, or risk of explosion symbol.
Indique une situation potentiellement dangereuse qui, si elle n'est pas évitée,
entraînera la mort ou des blessures graves.
WARNING
AVERTISSEMENT
Indicates a potentially hazardous situation that, if not avoided, could result in
death or serious injury. It may be associated with either a general hazard,
high voltage, or risk of explosion symbol.
Indique une situation de danger potentiel qui, si elle n'est pas évitée, peut entraîner la
mort ou des dommages corporels graves.
CAUTION
MISE EN GARDE
Indicates a potentially hazardous situation that, if not avoided, could result in
minor or moderate injury and/or damage to equipment. It may be associated
with either a general hazard, high voltage, or risk of explosion symbol.
When applied to software actions, indicates a situation that, if not avoided,
could result in loss of data or a disruption of software operation.
Indique une situation de danger potentiel qui, si elle n'est pas évitée, peut entraîner
des dommages corporels légers ou modérés.
Technical assistance
Contact information for technical assistance is listed in the following table. For the latest TAC
information, go to www.jdsu.com or contact your local sales office for assistance. Contact information
for regional sales headquarters is listed on the back cover of this document.
Assistance technique
Coordonnées pour l'assistance technique est listé dans le tableau suivant. Pour les dernières informations de
TAC, allez à www.jdsu.com ou contactez votre bureau de vente local pour assistance. Coordonnées pour le siège
régional des ventes est cotée sur le dos de ce document.