JDS Uniphase HP3-60-P4 User manual

ZPPKG0502
REV 1
FBP PROBE MICROSCOPE & HP360P4 SYSTEM
Probe and system with integrated power meter and patch cord microscope
USER MANUAL

USER MANUAL2
Notice Every eort was made to ensure that the information in this document was accurate at the time
of printing. However, information is subject to change without notice, and JDSU reserves the
right to provide an addendum to this document with information not available at the time that
this document was created.
Copyright © Copyright 2009 JDSU, LLC. All rights reserved. JDSU, Enabling Broadband and Optical
Innovation, and its logo are trademarks of JDSU, LLC. All other trademarks and registered
trademarks are the property of their respective owners. No part of this guide may be reproduced
or transmitted electronically or otherwise without written permission of the publisher.
Trademarks JDSU is a trademark of JDSU in the United States and other countries.
CleanBlast is a registered trademark of JDSU.
RibbonDrive is a trademark of JDSU.
Hirose is a trademark of Hirose Electric Group.
MTP is a registered trademark of US Conec, Ltd.
IBC is a trademark of US Conec, Ltd.
Molex is a registered trademark of Molex Incorporated.
OptiTip and OptiTap are trademarks of Corning Incorporated.
Sony is a registered trademark of Sony Corporation.
Specications, terms, and conditions are subject to change without notice. All trademarks and
registered trademarks are the property of their respective companies.
Patents RibbonDrive Tips: US Patent No. 6,751,017 / 6,879,439
CleanBlast: US Patent No. 7,232.262
Tested Equipment All pre-qualication tests were performed internally at JDSU, while all nal tests were performed
externally at an independent, accredited laboratory. This external testing guarantees the
unerring objectivity and authoritative compliance of all test results. JDSU's Commerce and
Government Entities (CAGE) code under the North Atlantic Treaty Organization (NATO) is
0L8C3.
FCC Information Electronic test equipment is exempt from Part 15 compliance (FCC) in the United States.
European Union Electronic test equipment is subject to the EMC Directive in the European Union. The EN61326
standard prescribes both emission and immunity requirements for laboratory, measurement,
and control equipment. This unit has been tested and found to comply with the limits for a
Class A digital device.
Independent
Laboratory Testing
This unit has undergone extensive testing according to the European Union Directive and
Standards.

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 3
TABLE OF CONTENTS
Chapter 1 JDSU FIBER INSPECTION SOLUTIONS.......................................................................................... 5–6
INSPECT BEFORE YOU CONNECTSM............................................................................................. 5
Simple Solution ................................................................................................................................. 5
Good Fiber Connection.................................................................................................................. 6
JDSU Fiber Inspection and Cleaning Solutions...................................................................... 6
Benets of Proactive Inspection.................................................................................................. 6
Chapter 2 FIBER OPTIC CONNECTORS ..........................................................................................................7–10
Key Terms and Concepts................................................................................................................ 7
Fiber Connector (Simplex)............................................................................................................. 7
Fiber Connection (Simplex)........................................................................................................... 7
Body ..................................................................................................................................................... 8
Ferrule................................................................................................................................................... 8
Fiber ..................................................................................................................................................... 8
Cladding ................................................................................................................................... 8
Core............................................................................................................................................ 8
Simplex and Multi-ber Connectors.......................................................................................... 8
Contamination................................................................................................................................... 9
Zones...................................................................................................................................................10
Zones Overlays.....................................................................................................................10
Acceptance Criteria........................................................................................................................10
Single-mode .........................................................................................................................10
Multimode.............................................................................................................................10
Chapter 3 FBP PROBE MICROSCOPE........................................................................................................... 11–12
Introduction......................................................................................................................................11
Controls..............................................................................................................................................12
Focus Control........................................................................................................................12
Magnication Control........................................................................................................12
Specications ...................................................................................................................................12

USER MANUAL4
Contents
Chapter 4 FBPT INSPECTION TIPS & ADAPTERS................................................................................... 13–15
Introduction......................................................................................................................................13
Barrel Assembly...............................................................................................................................13
Standard Tips....................................................................................................................................14
Long Reach Tips...............................................................................................................................14
APC Tips..............................................................................................................................................14
Angled Tips .......................................................................................................................................14
RibbonDriveTM Tips .........................................................................................................................14
Alignment Guides...........................................................................................................................14
FMA Adapters...................................................................................................................................14
FBPT Tip Installation Guide .........................................................................................................15
FBPT Standard Inspection Tips Matrix.....................................................................................15
FBPT RibbonDrive Inspection Tips Matrix..............................................................................16
Chapter 5 HP360P4 FIBER INSPECT & TEST SYSTEM....................................................................... 17–21
Introduction......................................................................................................................................17
HP3-60-P4 Features........................................................................................................................18
Components and Functions .......................................................................................................18
Improved Workow and Benets of PCM ..............................................................................19
Inspection Time Trial Comparison (Traditional Display vs. Display with PCM)............19
Integrated Power Meter Features .............................................................................................20
Power Meter Controls....................................................................................................................20
Power Meter Display Indicators.................................................................................................21
Measuring Modulated Light.......................................................................................................21
Service Information........................................................................................................................21
HP3-60-P4 Display Specications .............................................................................................22
Power Meter Specications.........................................................................................................22
Appendix JDSU FIBER INSPECTION VIDEO PROBE SOLUTIONS...........................................................27
Chapter 6 FIBER INSPECTION & TESTING................................................................................................. 23–26
Introduction......................................................................................................................................23
OTDR Trace of Contamination and Its Eect On Signal Performance..........................23
Absolute Power ...............................................................................................................................24
System Power Measurement......................................................................................................24
Relative Power .................................................................................................................................25
Reference Measurement..............................................................................................................25
Attenuation Measurement..........................................................................................................26

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 5
JDSU FIBER INSPECTION SOLUTIONS
INSPECT BEFORE YOU CONNECTSM
Simple Solution
CONTAMINATION IS THE #1 SOURCE OF TROUBLESHOOTING in optical networks.
A single particle mated into the core of a ber can cause signicant back reection,
insertion loss, and equipment damage. Visual inspection is the only way to determine if
ber connectors are truly clean before mating them.
By implementing a SIMPLE yet IMPORTANT process of proactive visual inspection and
cleaning, you can prevent poor signal performance and equipment damage.
1
JDSU Fiber Inspection Solutions CHAPTER 1

USER MANUAL6
CHAPTER 1 JDSU Fiber Inspection Solutions
The JDSU video ber inspection probe and handheld display system is used to quickly
and easily inspect connector end faces, which ultimately minimizes loss and optimizes
test conditions.Westover FBP-series video probes, available in digital or analog and single
or dual-magnication (200/400X) models are high-performance, handheld microscopes
designed for inspecting both female (bulkhead) and male (patch cord) connectors, as
well as other optical devices. The probe microscope can also be combined with a USB
converter module to inspect connectors via compatible test platforms and PC/laptop.
Our versatile systems oer a wide range of congurable solutions that can meet the
demands of any application.
JDSU Fiber Inspection
and Cleaning
Solutions
Reduce Network Downtime•
Reduce Troubleshooting•
Optimize Signal Performance•
Prevent Network Damage•
Benets of
Proactive Inspection
CLEAN CONNECTION
CORECLADDING
Light Transmitted
There are 3 basic principles that are critical to achieving an ecient ber optic
connection:
1. Perfect Core Alignment
2. Physical Contact
3. Pristine Connector Interface
Today’s connector design and production techniques have eliminated most of
the challenges to achieving core alignment and physical contact. What remains
challenging is maintaining a pristine end face.
Good Fiber
Connection

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 7
FIBER OPTIC CONNECTORS
2
Key Terms and
Concepts
Fiber connectors enable ber-to-ber mating by aligning the two optical bers. Fiber
connectors come in various types and have dierent characteristics for use in dierent
applications. The main components of a ber connector are detailed below:
Fiber Connector
(Simplex)
Fiber
Body
Ferrule
Fiber Connection
(Simplex)
Physical Contact
Fiber Ferrule Alignment Sleeve
Fiber Optic Connectors CHAPTER 2

USER MANUAL8
CHAPTER 2 Fiber Optic Connectors
Simplex Fiber Connector
A simplex ber connector contains a
single ber located in the center of the
ferrule. Common types include SC, LC, FC
and ST.
Simplex and
Multi-ber Connectors
Multi-ber Connector
A multi-ber/ribbon ber connector
contains multiple linear bers (4, 8, 12,
24, 48 or 72) in a single connector to
provide high-density connectivity. The
most common conguration is MPO (also
called the MTP®).
Ferrule
Fiber
Simplex Fiber Connector
Multiple Fibers
Ribbon Fiber Connector
Body Houses the ferrule that secures the ber in place; utilizes a latch and key mechanism that
aligns the ber and prevents the rotation of ferrules of two mated connectors.
Ferrule Thin cylinder where the ber is mounted and acts as the ber alignment mechanism; the
end of the ber is located at the end of the ferrule.
Cladding
Core
Ferrule
Body
Fiber Cladding
Glass layer surrounding the core, which prevents the signal in the core from escaping.
Core
The critical center layer of the ber; the
conduit that light passes through.

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 9
Fiber Optic Connectors CHAPTER 2
Contamination Dirt is everywhere, and a typical dust particle (2–15 μm in diameter) can signicantly
aect signal performance and cause permanent damage to the ber end face. Most eld
test failures can be attributed to dirty connectors, and most of them are not inspected
until the problem is detected, AFTER permanent damage has already occurred.
When dirt particles get on the core surface the light becomes blocked, creating
unacceptable insertion loss and back-reection. Furthermore, those particles can
permanently damage the glass interface, digging into the glass and leaving pits that
create further back-reection if mated. Also, large particles of dirt on the cladding layer
and/or the ferrule can introduce a barrier that prevents physical contact and creates an
air gap between the bers.To further complicate matters, loose particles have a tendency
to migrate.
Scratches are typically created during polishing, cleaning or mishandling ber connectors.
Scratches that touch the core are problematic because they create back reection.
CLEAN FIBER DIRT / CONTAMINATION
PITS / CHIPS SCRATCH
CLEAN CONNECTION
CORECLADDING
Light Transmitted
CLEAN CONNECTION
Light Transmitted INSERTION LOSS
DIRTY CONNECTION
CORE CLADDING
BACK REFLECTION
DIRTY CONNECTION

USER MANUAL10
CHAPTER 2 Fiber Optic Connectors
Zones are a series of concentric circles that identify areas of interest on the connector end
face. The inner-most zones are more sensitive to contamination than the outer zones.
A. Core
B. Cladding
C. Adhesive/Epoxy
D. Contact/Ferrule
Zones
ACCEPTANCE CRITERIA are a series of failure thresholds that dene contamination
limits for each zone.
Acceptance Criteria
ZONE NAME (Diameter) SCRATCHES DEFECTS
A. CORE Zone (0–25 μm) none none
B. CLADDING Zone (25–120 μm) no limit <= 3 μm
none > 3 μm
no limit < 2 μm
5 from 2–5 μm
none > 5 μm
C. ADHESIVE Zone (120–130 μm) no limit no limit
D. CONTACT Zone (130–250 μm) no limit none >= 10 μm
The tables below list the ACCEPTANCE CRITERIA standardized by the International
Electrotechnical Commission (IEC) for single-mode and multimode connectors as
documented in IEC 61300-3-35 Ed. 1.0.
Single-Mode
ZONE NAME (Diameter) SCRATCHES DEFECTS
A. CORE Zone (0–65 μm) no limit <= 5 μm
0 > 5 μm
4 <= 5 μm
none > 5 μm
B. CLADDING Zone (65–120 μm) no limit <= 5 μm
0 > 5 μm
no limit < 2 μm
5 from 2–5 μm
none > 5 μm
C. ADHESIVE Zone (120–130 μm) no limit no limit
D. CONTACT Zone (130–250 μm) no limit none >= 10 μm
Multimode
Zone Overlays A
B
C
D
Single-mode Multimode

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 11
FBP PROBE MICROSCOPE
3
JDSU'sWestover FBP Series Probe Microscopes are portable video microscopes used
to inspect ber optic connectivity. While most ber microscopes are limited to inspecting
“male” connectors, JDSU's FBP Probe is designed to inspect both simplex and multi-ber
(ribbon) types of both male and female connectors as well as optical devices, such as
transceivers. The probe is specially designed to t and operate comfortably and easily
in-hand, allowing the user to inspect hard-to-reach connectors that are installed on
the backside of patch panels or inside hardware devices. This eliminates the need to
disassemble hardware devices prior to inspection.
Introduction
FBP Probe Microscope CHAPTER 3

USER MANUAL12
The basic design of the Westover FBP probe microscope incorporates an imaging
system, integrated light source, video camera, focus mechanism and magnication
control. The probe is fully assembled and is powered by the display device. The only
assembly required by the user is the connection to the display device and installation
of the appropriate barrel assembly and/or the inspection tip. The FBP analog probe is
equipped with a 4-pin circular Hirose™ connector with notch-keys, which allows for a
secure and rm latch-lock connection to the display device.
Controls
Focus Control The focus control on the probe allows the user to adjust focus manually of the live ber
end face image on the display.
Magnication
Control
The magnication control (available only on dual-magnication probes) allows the user to
switch between LOW and HIGH magnications of the ber end face image.
Dimensions 140 x 46 x 43 mm (5.5 x 1.8 x 1.7 in)
Weight 180 g (6.3 oz)
Optical magnification 200X, 400X, 200/400X
Focus control Adjustable, in-probe
Cord length 240 cm (94-in)
Connector 4-pin Hirose™ male
Camera type 1/3-in CMOS Sensor
Video output NTSC or PAL
Light source Blue LED, 100,000+ hour life
Lighting technique Coaxial
Power source From the display device or USB module
Specications
Focus Control Magnication Control
(Dual-mag probes only)
Inspection Tip
Barrel Assembly
CHAPTER 3 FBP Probe Microscope

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 13
FBPT INSPECTION TIPS & ADAPTERS
4
JDSU’s comprehensive selection of over 250 precision, stainless-steel ber inspection tips
and adapters will inspect every connector and application. Our unique optics architecture
and design provide true versatility and adaptability, and are designed and engineered for
consistent and accurate inspection. These connector-specic and universal inspection
tips are interchangeable, which allow the probe to interface with dierent types of ber
connectors.
Introduction
The barrel assembly houses the objective lens and works in conjunction with a number
of tips.
Note: Certain tips are equipped with integrated optics and do not require a barrel assembly
(e.g., Long Reach Tips [FBPT-LC-L], Angled Tips [FBPT-SC-A6]).
FBPPBAP1 FBPPBAP2 FBPPBAP3
Barrel Assembly
FBPT Inspection Tips & Adapters CHAPTER 4

USER MANUAL14
FBPTSC (Bulkhead)
Standard Tips (Bulkhead and Patch Cord)
Standard bulkhead tips allow the user to inspect the ber end face on the female side of
the bulkhead (e.g., inside hardware devices or on the back side of patch panels).
FBPTU25M Patch Cord
Standard patch cord tips allow inspection of male ends of a ber connection (e.g., patch
cords, pigtails). Universal tips include the FBPT-U25M, compatible with 2.5 mm ferrules
(e.g., FC, SC, ST) and the FBPT-U12M, used to inspect 1.25 mm ferrules (e.g., LC, MU).
FBPTLCL
Long Reach Tips
Long reach tips have a 1/2-in longer reach than standard tips, and allow the user to
inspect the ber end faces in tight, hard-to-reach spaces.
FBPTSCAPC
APC Tips
APC tips are designed with an angle that complements the end face of an APC polish
ber connector. This allows the entire ber image to stay in focus during inspection.
FBPTSCA6
Angled Tips
Angled tips, identied by “A6,” are angled 60 degrees to allow easy maneuvering and
inspection of hard-to-reach locations such as transceivers on a printed circuit board (PCB)
or bulkheads located in tight spaces.
FBPTMTPA
RibbonDriveTM Tips
JDSU's patented RibbonDrive tips are specialty tips that allow inspection of high-density,
multiber array connectors that are mounted within a bulkhead adapter. Each tip mates
securely with connectors using a precision-keyed mating adapter interface. The patented
panning knob allows the user to view each ber individually in the linear array.
FBPTA8012001R
Alignment Guides
Alignment guides enable the inspection of various military and aerospace connectors
that use a plug and receptacle design. In addition to providing an alignment channel for
sockets, these alignment guides work in conjunction with a barrel assembly to prevent
the pins from breaking.
FMA Adapters
FMA Adapters provide optimized inspection for male connector ends and are ideal for
inspecting patch cords with multi-ber ribbon and APC polish connectors. FMA adapters
can be utilized by a probe microscope with a universal are adapter (FBPT-UFMA).
CHAPTER 4 FBPT Inspection Tips & Adapters

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 15
FBPT Inspection Tips & Adapters CHAPTER 4
JDSU oers a comprehensive selection of over 250 tips and
adapters that will inspect every connector and application. Visit our web site for a complete list of inspection tips and adapters.
FBPT Tip
Installation Guide
FBPT STANDARD INSPecTIoN TIPS (common tips shown)
CONNECTOR TYPE INSPECTION TIP APPLICATION DESCRIPTION
SC/UPC FBPT-SC Inspect SC/UPC connectors through a
bulkhead.
FBPT-U25M Inspect 2.5 mm UPC patch cord
connectors.
SC/APC FBPT-SC-APC Inspect SC/APC connectors through a
bulkhead.
FBPT-U25MA Inspect 2.5 mm APC patch cord connectors.
LC/UPC FBPT-LC Inspect LC/UPC connectors through a
bulkhead.
FBPT-U12M Inspect 1.25 mm UPC patch cord
connectors.
FBPT-LC-L Inspect LC/UPC connectors through a
bulkhead with 1/2-in longer reach.
LC/APC FBPT-LC-APC Inspect LC/APC connectors through a
bulkhead.
FBPT-U12MA-SF Inspect 1.25 mm APC patch cord
connectors.
Long Reach Tips
60° Angled Tips
RibbonDrive™ Tips
Barrel Assembly
Patch Cord Adapters
Standard Patch Cord Tips
Standard Bulkhead Tips

USER MANUAL16
CHAPTER 4 FBPT Inspection Tips & Adapters
FBPT STANDARD INSPecTIoN TIPS
CONNECTOR TYPE INSPECTION TIP APPLICATION DESCRIPTION
ST/
UPC
FBPT-ST Inspect ST/UPC connectors through a
bulkhead.
FBPT-ST-A6 Inspect ST/UPC connectors through a
bulkhead at a 60-degree angle.
FC/
UPC
FBPT-FC Inspect FC/UPC connectors through a
bulkhead.
FC/
APC
FBPT-FC-APC Inspect FC/APC connectors through a
bulkhead.
E2000/
APC
FBPT-E2000 Inspect E2000/APC connectors through
a bulkhead.
FBPT MulTI-FIBeR RIBBoNDRIve INSPecTIoN TIPS
CONNECTOR TYPE INSPECTION TIP APPLICATION DESCRIPTION
MTP®/UPC FBPT-MTP Inspect MTP®/UPC connectors through a
bulkhead.
MTP®/APC FBPT-MTPA-L Inspect MTP®/APC connectors through a
bulkhead (long reach).
MTP® Patch Cords FMA-MTPA & FBPT-UFMA Inspect MTP®/UPC or APC patch cords
(MTP®/APC inspection shown).
FCLT-MTP-MA Inspect MTP®/UPC or APC patch cords
(MTP®/APC inspection shown).

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 17
HP360P4 FIBER INSPECT & TEST SYSTEM
5
HP3-60-P4 Fiber Inspection and Test System CHAPTER 5
JDSU's HP3-60 series system combines the ability to inspect ber and measure optical
power into a single seamless handheld device. Derived from the popular HD3 series,
the HP3-60 provides high-quality image resolution in a compact, portable design, and
the integrated power meter oers quick, easy, and convenient eld measure of optical
power and attenuation. Easy push-button operation makes the device simple and
straightforward, while the inspect-test process procedure establishes proper, optimal
workow practices.
Introduction

USER MANUAL18
CHAPTER 5 HP3-60-P4 Fiber Inspection and Test System
Fiber end face inspection and optical power testing with the same device•
Integrated functions and features eliminate switching between multiple devices•
Instantly inspect ber when power level is low•
Signicantly reduces time for ber inspection and testing•
1.8-inch TFT LCD to view clear, crisp, detailed images of ber end faces with•
optimum resolution
Integrated patch cord microscope (PCM) for dedicated patch cord inspection•
PCM eliminates need for changing inspection tips, prevents misrouting, and•
protects patch cords
Ergonomic, small form factor design for ultimate portability•
Easy-to-use, simple operation•
HP3-60-P4
Features
Components and
Functions
1.8-in TFT LCD
Low Battery
LED Indicator
Univ. Push-Pull input for
Power Meter
4-pin Probe Input
Power Meter Operation
Controls
Power Button for System
Display for Wavelengths
and Types of Modulation
Battery Compartment for
6 X AA Batteries (back side)
Patch Cord
Microscope
(PCM) Input
FMAE Series
Adapter for PCM
Focus Control
for PCM
A/B Switch
(toggles patch cord
[PCM] and bulkhead
[probe] fiber views)

FBP PROBE & HP360P4 INSPECT AND TEST SYSTEM 19
HP3-60-P4 Fiber Inspection and Test System CHAPTER 5
Improved Workow
with PCM
With the integrated PCM, inspecting the bulkhead with the probe and the patch cord
with the PCM can be achieved with a push of a button.
3
INSPECT BULKHEAD
4
CONNECT
2
ACTIVATE PROBE
1
INSPECT PATCH CORD
Inspection Time Trial
(Average)
Traditional Display
Display with PCM
Reduce inspection time by more than 50 percent
Inspect the bulkhead with the probe and the patch cord with the display
No more changing, mishandling and misplacing inspection tips for the probe
Inspect 1 port/channel at a time and prevent mis-routing
Ensure patch cords stay clean byparking it in the patch cord microscope before
connecting
Benets of
2-Microscope System

USER MANUAL20
CHAPTER 5 HP3-60-P4 Fiber Inspection and Test System
Power Meter Controls
Easy-to-use, straightforward operation•
Reliable basic functionality for optical testing•
Suitable for all single-mode and multimode applications, such as LAN, TELECOM,•
CATV, and DWDM testing
Universal Push-Pull (UPP) interface for 2.5 mm and 1.25 mm connectors•
Use with JDSU light source to detect modulation frequency and identify•
individual bers
TWINtest and Auto-• λ (with JDSU light source)
Integrated
Power Meter Features
Protective Rubber
Cap
Universal Push-Pull
(UPP) Power Meter
input
SHORT KEY PRESS:Switches between absolute and relative power
level display
LONG KEY PRESS:Stores a reference power level
dBm/dB
Sets the calibrated wavelength; ve possible wavelengths.
λ
SHORT KEY PRESS:Brief operating mode
LONG KEY PRESS:Permanent operating mode
Power Meter Operation
Controls
Display for Wavelengths
and Types of
Modulation
4-pin Probe Input