JEHNERT SOUND DESIGN 68501 User manual

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
Packing list:
Package 1 (Art. No. 68601):
2x »XA19 DUC« Neodymium soft dome tweeter Ø 19mm
2x »XA165« Low-midrange »Power-Woofer« Ø165mm incl.
2x Mounting ring for »XA165« with M4x16 pre-mounted on woofer
1x Center crossover
4x Alubutyl blank 110 x 220 x 3mm
Recommendation:
To achieve the full sound performance of the sound system, we recommend the expansion set, which significantly
increases the sound performance of the system with the additional amplifier and subwoofer.
Fiat Ducato Series 8: for an optimal sound experience, the complete insulation of the door lining is recommended.
(required damping material not included, can be reordered, Art.No.: 27970)
Required tools / accessories
• Phillips screwdriver
• Torx screwdriver (TX 20/25/30)
• Gloves
• Plastic wedge
• Padding material for surface protection
• Tray, or similar for storing small parts
• Insulating tape
Radio settings:
To achieve the best sound, all settings on the radio (bass, treble, loudness, equalizing, etc.)
should be set to ZERO or OFF.
Watch installation video on
youtube
2-way sound system Fiat Ducato III and Serie 8
»68501 Front «

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
CD
A B
EF
C: Remove the protective paper of the enclosed Alubutyl blanks, heat them with a hair dryer and press them firmly
with the butyl side (adhesive) on the sheet metal behind the woofer opening -> wear gloves as heat protection!
D: Screw in the JEHNERT Upgrade loudspeaker with the original screws and connect the original plug to the
connect the loudspeaker
A: Use a plastic wedge to carefully lift the cover of the woofer and remove it.
B: Use a Phillips screwdriver to loosen the screws of the woofer, remove it and
disconnect the cable from the housing.
E: Push the foam hose over the connector and slide it through the opening into the free space
under the fairing
F: Finally, replace the plastic cover and clip it in place.
1a. mounting the woofer (Serie III)
(at original woofer mounting position)

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
F
1b.1. removal of the door panel
AB C D
G
H I J
E
• unclip the door
1b. Mounting the woofers (Series 8)
(at original woofer mounting position)
• Use a plastic wedge to carefully remove the door panel cover so that no scratches occur, secure the edges with adhe-
sive tape. (Fig. A-C)
• Use a slotted screwdriver to remove the screws and covers of the door trim (Fig. D-J)
! remove all screws 8 x TX30 1x TX20 (Fig. E)
C: Finally, remove the two screws from the door handle and carefully remove the door trim. (Fig. G)
D: Use your finger to pry out the door handle connection and remove the door handle. (Fig. I)
F: Now the woofer can be installed.

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
A B
C D E
1b.2. mounting the woofer (Serie 8)
(at original woofer mounting position)
• Disassemble all screws of the factory woofer (pick up screws) 3x TX20
• Using a TX20 screwdriver, install the three screws from the woofer ring to the vehicle door.
• Connect the cables together. (see fig. D)
• Refit the door trim. (Attach screws)(fig. E)

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
CD
A B
EF
A: Loosen 2 plastic screws on each side at the top of the REMIS roller blind frame. Disassemble/assemble the driver‘s
and co-driver‘s one after the other so that the roller blind is always fixed on one side.
B: Loosen the door sealing rubber in the area of the A-pillar.
2. mounting tweeter
(in original installation opening in Remis blackout blind)
C: Carefully remove A-pillar trim, place on dashboard (->protect surface with adhesive tape if necessary)
and unclip and unplug existing original tweeter
D: Connect JEHNERT tweeter, clip it into the holder and turn it in the holder until it clicks into place.
E: Push connector into foam hose
F: Push foam hose into gap between dashboard and A-pillar.
Reassemble trim parts and door seal in reverse order -> For A-pillar trim ensure correct position of clips and cables
(without illustration)

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
Notes:

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
Warranty:
As the manufacturer, we provide a warranty of 3 years for these sound systems, calculated from the date of purchase from the specialist dealer.
Within this warranty period, we will, at our option, repair or replace free of charge all defects that are due to material or manufacturing defects.
Excluded from the warranty are damages which are due to improper use or installation, to wear and tear or to interventions by third parties.
by third parties. The warranty does not cover consequential damage or defects that only insignificantly impair the value or usability of the sound systems.
A warranty obligation is not triggered in the case of damage caused by external influences.
Systems with additional or incorrect mounting holes are excluded from exchange. These are damages to the components that cannot be repaired.
Notes:

Assembly instruction
Status: 07.02.2023
Fiat Ducato III + Serie 8,
CampTec Style
Basic Installer Paket, 2-Ways
Jehnert Sound Design I Im Michelreis 14 I 72124 Pliezhausen I Tel.: [phone] I [e-mail] I www.jehnert.de
Art. No. 68501
Share your Sound Experience
with #JehnertSoundDesign
facebook.com/jehnertsounddesign Subscribe us on Youtube
Radio Tweeter »XA 19 DUC« (68501 Scope of delivery)
Mounting in the A-pillar.
Amp V40 CampTec (included in all expansion
packages)
Subwoofer MiKo (68502 Scope of delivery)
Subwoofer Magnetic (68503 Scope of delivery)
Door subwoofer (68504 Scope of delivery)
woofer »XA 165« (68501 scope of delivery)
Mounting in the vehicle door panels.
CampTec Style expansion options
The 2-way front system CampTec Style can be optionally expanded with an amplifier and subwoofer (different versions selectable) to
significantly increase the sound experience again.
If you have any questions, please do not hesitate to contact our team in Pliezhausen:
JEHNERT SOUND DESIGN
»Development and production of car audio systems«
Owner: Hans-Peter Jehnert
Im Michelreis 14
72124 Pliezhausen
Phone: [phone]
Fax: 07127 / 93457-10
[email protected]
www.jehnert.de