Jenn-Air JGW9130ADW User manual

INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE
GAS INSTALLATION MANUAL
30" BUILT-IN OVENS
PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE
THEMANUALIS INTENDEDTOASSISTIN THEINITIALINSTALLATIONANDADJUSTMENTSOF THERANGE.
SPECIALWARNING
ONLY QUALIFIED PERSONNEL SHOULD INSTALL OR SERVICE THIS RANGE.
READ "SAFETY INSTRUCTIONS"IN USE & CARE BOOK BEFORE USING
RANGE.
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE,
MAINTENANCE OR USE OF OVEN CAN RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE.
NOTE:CHECKTHE MODELNUMBERPLATEONYOUR 30"GASWALLOVEN,LOCATEDON BOTTOM£
CONTROLPANELLOWERTRIM,TO SEE IFITIS APPROVEDFOR INSTALLATIONINCANADA.
CAUTION:SOMECABINETSANDBUILDINGMATERIALSARE NOTDESIGNEDTOWITHSTANDTHEHE[
PRODUCED BY THE NORMAL SAFE OPERATION OF A LISTED APPLIANCE. DISCOLORATION C
DAMAGE,SUCHAS DELAMINATION,MAYOCCUR.
YOUR RANGE MAY NOT BE EQUIPPED WITH SOME OF THE FEATURES REFERRED TO
IN THIS MANUAL.
8101P357-1
(05-2000-(

30"BUILT-IN GAS OVEN
120 VACPOLARIZED-
ELECTRIC SUPPLY
LOCATION.
CUTOUT FOR EL
CORD TO BE SEALED 7/B:: MAX.
AFTER INSTALLATION. 33 3/4MIN
CENTERLINEOF
CABINET OPENING
SOLID CABINET 29 1/2"
BOTTOMREQUIREDMIRECOMMENuLU
I[ 12" MIN.
2"OiA. MIN.HOLE _ "S _ N
FOR HOUSE PIPING "" .a,,'I.. ¢"
TO BESEALED
AFTER INSTALLATION.
HOUSE PIPING TO BE
REDUCED TO FIT 3/8"
NPT INLET PIPING. _ _ __
-2-

30"BUILT-IN GAS OVEN/MICROWAVE
COMBINATION
20A,120 VAC
POLARIZED ELECTRI
SUPPLY LOCATION.
CUTOUTFOR ELECTRICAl
CORD TO BESEALED
AFTER INSTALLATION.
CENTERLINE_30/4."MAX.
CABINETOPENING30/8" MIN.
44 3/8"MAX.8'_
4,$I/4"MIN.30 7/
"2 1/4"
SOLID
BOTTOM REQUI RED. // MIN. RECOMMENDED
INSIDE 12" N.
-- -1" MIN
'%.
2" DIA. MIN.HOLE "- ""_"
-%
FOR HOUSE PIPING <
TO BE SEALED AFTER
INSTALLATION.
HOUSE PIPING TO BE
REDUCED TO F_T
3/8" NPT INLET PIPING.
_3"MIN.
-3-

INSTALLATION
A WIRINGDIAGRAMISENCLOSEDINTHE ENVELOPE ClearanceDimensions
WITH THIS BOOKLET; ALSO THERE IS A DIAGRAM
GLUEDTO THEUNIT, BEHINDCONTROLPANEL. Forcompleteinformationin regardto the installationof wall
ovensand clearancessee the installationdrawings.
Check the oven model number plate to see if the oven is
approved for installation in mobile homes and/or
recreationalvehicles. If approved the following items are LocatingThe Unit
applicable.NOTE:Ovenmodel numberplateis locatedon
bottomof controlpanellowertrim. The installationdrawing,gives the minimumdimensionsof
the cabinetcut-outfor the ovenand the locationof the gas
andelectricaloutlets.Thedimensionsgivenarefortheoven
MobileHomes bottomto bea minimumof 12" inchesabovethe floor.The
The installation of an oven designed for mobile home recessinwhichtheovenistobeinstalledshouldhaveasolid
installation must conform with the Manufactured Home floor and be so constructed as to provide a complete
ConstructionandSafetyStandard,Title24CFR,part3280 enclosure around the recessed portion of the oven to
(formerly The Federal Standard for Mobile Home prevent drafts which may result in inconsistent and
Constructionand Safety,Title 24, HUD part280)or, when unsatisfactoryburnerandbakingperformance,itshouldbe
such standard is not applicable, the Standard for perfectly level to provide a solid, level foundation for the
ManufacturedHomeInstallation,ANSIA225.1/NFPA501A, ovenunit.Theopeningsintheenclosureforgasandelectric
serviceshouldbesealedbeforetheovenisinstalled.Airfor
or with local codes, combustionentersat the extremebottomoffront panel.Do
InCanadatheovenmustbeinstalledinaccordancewiththe notblockorobstructthis opening.
current CSA Standard C22.1 - Canadian Electrical Code
Part 1andSectionZ240.4.1- InstallationRequirementsfor For SAFETY CONSIDERATIONS fasten the oven to the
Gas BurningAppliancesin Mobile Homes (CSA Standard cabinet with the four (4) screws (shipped with the unit)
CAN/CSA- Z240MH). through the holesinthe trim behindthe ovendoor. Theunit
should beleveled properly before being secured to the
cabinet.
RecreationalVehicles
The installation of an oven designed for recreational
vehiclesmust conform with state or other codesor, in the
absenceofsuchcodes,withthe Standardfor Recreational
Vehicles,ANSIA119.2-latestedition.
In Canadathe oven must be installedin accordancewith
CAN/CSA - Z240.6.2 - Electrical Requirementsfor R.V.'s
(CSAStandardCAN/CSA- Z240 RV Series) and Section
Z240.4.2 Installation Requirements for Propane
Appliances and Equipment in R.V.'s (CSA Standard
CAN/CSA- Z240 RV Series).
-4-

CONNECTINGTHE OVEN
Electric Supply PRESSURESIN EXCESS OF 0.5 P.S.I. CANDAMAGE
THE APPLIANCE PRESSURE REGULATOR AND
The appliance, wheninstalled, must be electrically OTHERGAS COMPONENTSINTHIS APPL(ANCEAND
groundedin accordancewithlocalcodesor,intheabsence CAN RESULTIN A GAS LEAK.
of local codes, with the NationalElectrical Code,
ANSI/NFPA70. a. A GAS CUTOFF VALVE SHOULD BE PUT IN AN
ACCESSIBLE LOCATION IN THE SUPPLY LINE
InCanadatheovenmustbeinstalledinaccordancewiththeAHEAD OF THE UNIT, FOR TURNINGON AND
current CSA Standard C22.1 - CanadianElectricalCode TURNING OFF GAS SUPPLY.If the unit is to be
Part 1.connected to house piping with flexible or semi-rigid
metalconnectors for gas appliances, CONNECTOR
ELECTRICALSUPPLYCONNECTION: NUTS MUST NOT BE CONNECTED DIRECTLYTO
The oven requires120volts, 60cycle alternatingcurrent PIPE THREADS. THE CONNECTOR MUST BE
from an outlet capable of supplying 15 amperes for INSTALLEDWITHADAPTORSPROVIDEDWITHTHE
non-combounits and 20 amperesfor combo units (with CONNECTOR.
microwave). b. Thehousepipingand/orovenconnectorusedtoconnec
the oven to the maingas supply must beclean,freeo
WARNING metalshavings,rust, dirt and liquids (oilor water). Dirt
ElectricalGroundingInstructions etc.inthesupplylinescancausefailureofthegasvalve,=
This applianceis equipped with a(three-prong) or controlsandctog burners.
groundingplugfor yourprotectionagainstshockhazard
andshouldbepluggeddirectlyintoa properlygrounded CAUTION:DONOTLIFT ORMOVETHEWALLOVEI
receptacle.Do not cut or removethegroundingprong BYTHE DOOR HANDLES.
fromthisplug,c.Turn off all pilotsandmaingas valveof other ga
appliances.
WARNING d.Turnoff maingas valveatmeter.
DISCONNECT ELECTRICAL SUPPLY
BEFORESERVICINGTHEAPPLIANCE.e.Beforeconnectingtheunit,applypipethreadeompour
approvedfor LPGto allthreads.
f.Connectunittogas supply.
GasSupply
Installationofthisovenmustconformwithlocalcodesor,in g. Turn on main gas valve at meter, and relight pilots
other gas appliances.
the absence of local codes, with the National FuelGas
Code,ANSIZ223.1-latestedition, h. Applyanon-corrosiveleakdetectionfluidtoalljointsa_
fittings in the gas connectionbetween the supply lil
InCanadatheovenmustbeinstalledinaccordancewiththe shut-off valve and therange. Includegas fittings a,
currentCGAStandardCAN/CGA-B149- InstallationCodes joints inthe range if connectionswere disturbedduri
for Gas BurningAppliancesand Equipment andor local installation.Checkfor leaks!bubblesappearingarou
codes, fittings and connectionswill indicate a leak. If a I_
appears,turn off supply linegas shut-offvalve,tight
GAS SUPPLY CONNECTION: connections,turnonthe supplylinegas shut offval,
A TRAINED SERVICEMAN OR GAS APPLIANCE andretestforieaks. Nevertest forgas leakswithano_;
INSTALLER MUST MAKE THE GAS SUPPLY flame.
CONNECTION.Leak testing ofthe appliance shall be
conducted by the installer according to the CAUTION: NEVER CHECK FOR LEAKS WlTI_
instructionsgivenin sectionh.FLAME.
NATURAL GAS SUPPLY LINE MUST HAVEAWHENLEAKCHECKISCOMPLETE,WIPEOFF
NATURAL GAS SERVICE REGULATOR. INLET RESIDUE.
PRESSURE TOTHIS APPLIANCESHOULD BE
REDUCED TO A MAXIMUM OF 14 INCHES WATER i,Adjustburnerairshuttertothewidestopeningthat
COLUMN (0,5 POUNDSPER SQUAREINCH (P,S,I,)not causetheflameto lift or blowoff theburnerw
LIQUEFIED PETROLEUM(L.P,)/PROPANE GAS cold.
SUPPLYLINE MUST HAVE AL.P. GAS PRESSURE
REGULATOR.INLET PRESSURETOTHIS APPLIANCE BEFORELIGHTING ANY BURNER, SEE THAT
SHOULD BE REDUCED TO A MAXIMUM OF 14 PACKING MATERIALS HAVE BEEN REMO\
INCHES WATER COLUMN (0.5 P.S.I.). INLET FROMTHE UNITS.
-5-

UNIT ADJUSTMENTS
Wall Oven Adjustment
ELECTRICIGNITION- BAKE BURNERWITH AIR SHUTTER - OVEN BURNER
ELECTRICGLOW BAR d. The approximatelengthofthe flameof oven burner isa
a. The bake burner is equipped with an electric control 1/2inchdistinctblueflame, figure1.
system as well as anelectric oven burner ignitor.This e. Oven burner flame can be checkedas follows,without
controlsystem requires NO adjustment.To operate, burnerbafflein place:
pressBakeTemporBroilbutton,turnsetknobtodesired
temperatureor Hi/Lobroil.Currentwillflowtotheignitor. 1.Yellowflameonburner-openburnerairshuttertothe
Itwill"glow"similarto a lightbulb.(Thisglowmaybewidestopeningthatwillnotcausetheflameto liftor
reflectedintotheoventhroughtheopeningsintheovenblowofftheburnerwhencold.(Seefigure2.)
bottom).Whenthe ignitorhasreacheda temperature2. Distinctblueflamebutlifting- closeburnerairshutter
sufficientto ignitegas, the electricallycontrolledoven tothepointwhereitwillnotcausethe flameto liftor
valvewillopenandflamewillappearattheovenburner, blowofftheburnerwhencold.(Seefigure2.)
Thereisatimelapsefrom30to45secondsaftertheunit
isturnedON beforeflameappearsat the oven burner._._ Lt.,.. %
Whentheoven hasreachedthedialsetting,the glowing
ignitorwillgo OFF. The burner flamewillgo "out" in 20 , \\ o,,
to 30secondsafter theignitorgoes "OFF".To maintain _--\ \_'_ "_ -_ _t_--'_-'_*_
any givenoventemperaturethis cycle will continueas \ _ _ _ _y._-,.____
longas the dialisat thegiventemperature. _._.__ ._ _.._'_-"-'_.,.....
b. In caseservicingshould becomenecessary,a manual
gas valve to shut off the gas to the oven burner is
suppliedbetweenthe gasregulatorand the gas inlet.It _ -"'t_--__" "" -_"_-'_
islocatedatthe rightfrontofthe ovenbottom.Toaccess _._ L_ "_'_"
theshut off valve,removethe Iouveredbottomtrim. I/'2" INNER BLUEFLAME
c. The ovenCANNOTbeused during periods of power FIGURE 1
outage, in caseof powerfailure,turn the thermostatto
theOFF position.
AIRSHUTTER
LOCKSCREW
LOCK S_RL_/_'_ORIFICE
FIGURE 2
-6-

GASCONVERSION
General
All ovens are equipped with double coaxial (universal) 2. Unsnapthe plasticplungerfrom the bottomof the bras
orificesandwithaconvertibleappliancepressureregulator,hexnut,andturnthe plungerover.Thegas type youar
The oven model number plate states which gas it was convertingto MUSTbevisible on lowerside of plunger
adjustedforatthefactory.NOTE:Ovenmodelnumberplate
is locatedonbottomof controlpanellower trim.To convert 3.Snapplungerbackin tobottomofthe brasshexnut,an
the unit to either Natural gas or LP gas will require installbrass hexnut backintoregulator.(Seefigure3).
adjustmentof theorifice hoodandairshutteronthe burner
and adjustment of the appliance pressure regulator
convertercap.
Inletpressuretotheappliancepressureregulatorshouldbe Checking Manifold Gas Pressure
as follows for both operation and checking of appliance BUILT-IN OVENS:
pressureregulatorsetting: Onbuilt-inovens,remove1/8inchpipeplugfromsideofga
pressureregulator,install 1/8" "B" valve, 1/8 inch piece £
INLET PRESSUREIN NATURAL LP pipe,connect manometer,makesure main burner ison b
INCHESOF WATERCOLUMN GAS GAS obtainaccuratepressurecheck.
Minimum 5 11
Maximum 14 14 Be surethe gas supply (house piping)pressureis at leas
one inch(1") abovespecifiedrangemanifoldpressure.Th(
Appliance Pressure Regulator gassupply pressureshouldneverbe overfourteen inche_
Conversion (14")watercolumn.
Theovensappliancepressureregulatormust be set to
matchthetypeofgassupplyused.Ifconvertingfromnatural
gasto LPgas, the appliancepressureregulatormust be Checking Pressure Of House Piping
convertedto regulateLP gas.If convertingfromLPgastoSystem
natural gas, theappliancepressureregulatormustbe
convertedtoregulatenaturalgas.ThetypeofgasforwhichTheapplianceand itsindividualshutoff valve mustb(
theregulatoris setforwillbevisibleontheplasticplunger disconnectedfromthegassupplypipingsystemduringan_
whichis snappedonto the bottomofthebrasshexnut pressuretestingofthatsystemat test pressuresinexces,,
(eitherNat.or LP). of1/2 Ibs./sq.in.(14in.W.C.).
TO CONVERT THEAPPLIANCE PRESSURE
REGULATORFROMONE GAS TO ANOTHER, DOTHE The appliancemust beisolatedfromthe gas supplypipinc
FOLLOWING: systemby closingitsindividualmanualshutoffvalvedurinc
anypressuretestingofthe gassupplypipingsystemattes
1. Removethe brass hexnutfromthe regulator,pressuresequaltoor lessthan 1/2Ibs./sq.in. (14in.W.C.)
GA_KET_
I"
TO"ON'POSITION. _ _9._ __
IAR -_AS PRESSURE TAPE
WHEN THE INSTALLER HAS COMPLETED INSTALLATIONOF APPLIANCE, LEAVE THE
APPLIANCE PRESSURE REGULATOR SHUT-OFF VALVE INTHE "ON" POSITION.
FIGURE3
-7-

ORIFICE CONVERSION
1. FROMNATURALGAS TO LP/PROPANEGAS: 2. FROM LP/PROPANEGAS TO NATURALGAS:
a. Change the appliance pressure regulator from a. ChangetheappliancepressureregulatorfromLPto
naturalto LPsetting.(Seefigure 3).naturalsetting.(Seefigure3).
b. Screwthe burner orifice hoodsdown tight against b. Screwthe burnerorificehoodsawayfromthe pins.
the pins. (See figure 4B).Use care to not over (Seefigure4A). Approximately1 1/2 to 2 turns.
tighten.Overtighteningcandamagethe coaxialpin
insidethe orificehood. c.Adjustburner airshuttertothewidest openingthat
will notcausethe flameto lift orblow offthe burner
c.Adjustburnerair shutterto the widestopeningthat whencold.
will not causethe flameto lift or blowoff the burner
whencold. NOTE: Correctly adjusted sealed burners, the
flamewill lift or blowwithout a pot over the burner.
NOTE:Correctlyadjustedsealedburners,can have Theseshould beadjustedwith a pot in place.
flames that will lift or blow without a pot over the
burner. These should be adjusted with a pot in
place.
ORI SERVICE-PARTSINFORMATION
FICE
,_T_9219-,,3-o WHEN YOUR RANGE REQUIRES SERVICE OR
REPLACEMENTPARTS,CONTACTYOUR DEALEROR
FIGURE4A FIGURE4B AUTHORIZEDSERVICE AGENCY. PLEASE GIVE THE
NATURALGAS LP GAS COMPLETEMODEL AND SERIAL NUMBERSOF THE
SETTING SETTING RANGEWHICH IS LOCATEDON THE RANGEMODEL
NUMBERPLATE.
-8-