Jenn-Air Euro-Style Design JS48SSDUDE User manual

W11311786A
Table of Contents/Table des matières/Índice...................................................................................2
INSTALLATION GUIDE
For questions about features, operation/performance, parts, accessories, or service,
call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.
In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.
Get the app, connect instructions, terms of use, and privacy policy at www.jennair.com/connect.
GUIDE D’INSTALLATION
Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou service,
composerle1800JENNAIR (1800536-6247) ou visiter le www.jennair.com.
Au Canada, composer le 1800JENNAIR (1800536-6247) ou visiter le www.jennair.ca.
Obtenez l’application et les instructions de connexion, les conditions d’utilisation
et la politique de condentialité au www.jennair.com/connect.
GUÍA PARA LA INSTALACIÓN
Si tiene preguntas respecto a las características, funcionamiento/rendimiento, piezas, accesorios o servicio,
llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web www.jennair.com.
En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web en www.jennair.ca.
Obtenga la aplicación, las instrucciones de conexión, los términos de uso y la política de privacidad en www.jennair.com/connect.
JENNAIR®FRENCH DOOR
REFRIGERATOR
RÉFRIGÉRATEUR DE PORTE
ÀDOUBLEBATTANT JENNAIR®
REFRIGERADOR JENNAIR®
DE DOS PUERTAS

REFRIGERATOR SAFETY..............................................................3
42" MODELS...................................................................................4
48" MODELS...................................................................................4
INSTALLATION REQUIREMENTS.................................................5
Tools and Parts.............................................................................5
Location Requirements................................................................5
Electrical Requirements ...............................................................6
Water Supply Requirements ........................................................7
Tipping Radius .............................................................................7
Product Dimensions.....................................................................8
Door Swing Dimensions...............................................................8
Custom Side Panels.....................................................................9
INSTALLATION INSTRUCTIONS.................................................10
Unpack the Refrigerator.............................................................10
Reduce Tipping Radius (if required)...........................................10
Move the Refrigerator into House..............................................10
Install Anti-Tip Boards................................................................11
Connect the Water Supply.........................................................11
Plug in Refrigerator ....................................................................13
Move Refrigerator to Final Location ..........................................13
Level and Align Refrigerator.......................................................14
Adjust Doors...............................................................................14
Install Side Panel........................................................................15
Install Base Grille........................................................................15
Complete Installation .................................................................16
Water System Preparation .........................................................16
TABLE OF CONTENTS
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR...............................................17
MODÈLES DE 42" ........................................................................18
MODÈLES DE 48" ........................................................................18
EXIGENCES D’INSTALLATION ...................................................19
Outils et pièces...........................................................................19
Exigences d’emplacement.........................................................19
Spécications électriques..........................................................20
Spécications de l’alimentation en eau.....................................21
Rayon de basculement ..............................................................21
Dimensions du produit...............................................................22
Dimensions pour l’ouverture des portes....................................22
Panneaux latéraux personnalisés..............................................23
INSTRUCTIONS D’INSTALLATION.............................................24
Déballage du réfrigérateur..........................................................24
Réduire le rayon de basculement (le cas échéant)....................24
Déplacement du réfrigérateur dansledomicile.........................24
Installation de planches antibasculement .................................25
Raccordement à la canalisation d’eau ......................................25
Brancher le réfrigérateur ............................................................28
Déplacement du réfrigérateur àsonemplacement dénitif......28
Réglage de l’aplomb et alignement duréfrigérateur.................28
Ajustement des portes...............................................................29
Installation du panneau latéral ...................................................30
Installation de la grille de la base...............................................30
Terminer l’installation..................................................................31
Préparation du circuit d’eau.......................................................31
SEGURIDAD DEL REFRIGERADOR...........................................32
MODELOS DE 42" (106,7 CM).....................................................33
MODELOS DE 48" (122 CM)........................................................33
REQUISITOS DE INSTALACIÓN.................................................34
Herramientas y piezas................................................................34
Requisitos de ubicación.............................................................34
Requisitos eléctricos..................................................................35
Requisitos del suministro de agua.............................................36
Arco de vuelco ...........................................................................36
Dimensiones del producto.........................................................37
Medidas de oscilación de las puertas .......................................37
Paneles laterales a la medida ....................................................38
INSTRUCCIONES DE INSTALACIÓN.........................................39
Desembale el refrigerador..........................................................39
Cómo reducir el arco de vuelco (de ser necesario)...................39
Cómo hacer entrar el refrigerador enlacasa............................39
Cómo instalar los tableros anti-vuelco ......................................40
Conexión del suministro de agua ..............................................40
Cómo enchufar el refrigerador...................................................43
Cómo mover el refrigerador asuubicaciónnal.......................43
Nivelación y alineamiento del refrigerador.................................43
Cómo ajustar las puertas...........................................................44
Cómo instalar el panel lateral.....................................................45
Instalación de la rejilla de la base ..............................................45
Completar la instalación ............................................................46
Preparación del sistema de agua ..............................................46
ÍNDICE

3
REFRIGERATOR SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.

4
42" MODELS
Euro-Style Design
Features stainless steel wrapped doors with towel bar handles.
JS42SSDUDE
Pro-Style®Design
Features stainless steel wrapped doors and Pro-Style®handles
with diamond-etched grip.
JS42PPDUDE
48" MODELS
Euro-Style Design
Features stainless steel wrapped doors with towel bar handles.
JS48SSDUDE
Pro-Style®Design
Features stainless steel wrapped doors and Pro-Style®handles
with diamond-etched grip.
JS48PPDUDE

5
INSTALLATION REQUIREMENTS
Tools and Parts
IMPORTANT:
■Installer: Leave Installation Instructions with the homeowner.
■Homeowner: Keep Installation Instructions for future reference.
Save these Installation Instructions for the local electrical
inspector’s use.
Tools Needed:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
■Cordless drill ■11/32" nut driver
■Drill bits
■Adjustable wrenches (2)
■3/8" and 1/2" open-end
wrenches
■Phillips screwdriver ■5/32" hex key
■Small level ■1/4" and 5/16" socket drivers
■Appliance dolly ■Tape measure
■Torx†T27 screwdriver ■Utility knife
Parts Needed:
■#8 x 3" (7.6 cm) wood screws (longer screws may
be needed) (6)
■2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s) (1 or 2)
■If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
1/4" (6.35 mm) compression tting.
Location Requirements
The refrigerator can be recessed in an opening between cabinets
or installed at the end of a cabinet run using a side panel to
enclose the refrigerator.
IMPORTANT: This appliance is intended to be used in household
and similar applications such as:
■Staff kitchen areas in shops, ofces and other working
environments.
■Farm houses and by clients in hotels, motels and other
residential type environments.
■Bed and breakfast type environments.
■Catering and similar non-retail applications.
†TORX is a trademark of Acument Intellectual Properties, LLC
■Observe all governing codes and ordinances.
■It is recommended that you do not install the refrigerator near
an oven, radiator, or other heat source.
■Do not install in a location where the temperature will fall below
55°F (13°C).
■Floor must support the refrigerator weight, more than 600 lbs
(272 kg), door panels and contents of the refrigerator.
■Ceiling height must allow for side tipping radius.
See “Tipping Radius.”
■Location should permit door to open fully.
See “Door Swing Dimensions.”
■Location must permit top grille removal.
See “Opening Dimensions.”
Opening Dimensions
■To avoid tipping during use, the solid soft must be within
1" (2.5 cm) maximum above the refrigerator. If the solid soft
is higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If anti-tip boards are needed, they must be installed to the rear
wall studs so that the bottom of the anti-tip board is
84" (213 cm) from the oor. See “Install Anti-Tip Boards” for
more information.
NOTES:
■A clearance of 1/2" (1.3 cm) must be maintained above the
top grille in order for the top grille to be removed.
■Do not remove the foam gasket from the top of the
compressor cover unless removal is necessary to t the
unit under a soft. Removal of the gasket will cause loss in
cooling efciency.
■If installing under a solid soft, after, installation raise the
leveling legs so that the gasket is pressed snugly against
the soft.
■A grounded 3 prong electrical outlet should be located
within a specied number of inches from the right-hand side
cabinets or end panel. See the chart following the graphic
for the number of inches required for your model. For more
information, see “Electrical Requirements.”
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
B
A
A. Gasket
B. Compressor cover
1/2"
(1.3 cm)

6
■The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the oor. See
“Water Supply Requirements” for more information.
Model Width A
(as shown above)
Dimension B
(as shown above)
42 41¹⁄2" to 41³⁄4"
(105.4 cm to 106.1 cm)
7¹⁄2" (19.1 cm)
48 47¹⁄2" to 47³⁄4"
(120.7 cm to 121.3 cm)
13¹⁄2" (34.3 cm)
NOTE: Flooring under refrigerator must be at same level as the
room. Face of cabinetry must be plumb.
Electrical Requirements
Before you move your refrigerator into its nal location, it is
important to make sure you have the proper electrical connection.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualied person. Do
not use a cord that shows cracks or abrasion damage along its
length or at either the plug or connection end.
Recommended Grounding Method
A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded electrical
supply is required. It is recommended that a separate circuit
serving only your refrigerator be provided. Use an outlet that
cannot be turned off by a switch. Do not use an extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground Fault
Circuit Interrupter) protected outlet, nuisance tripping of the power
supply may occur, resulting in loss of cooling. Food quality and
avor may be affected. If nuisance tripping has occurred, and if
the condition of the food appears poor, dispose of it.
NOTE: Before performing any type of installation or cleaning,
remove the top grille and turn the master power switch to OFF or
disconnect power at the circuit breaker box.
When you are nished, turn ON the master power switch or
reconnect power at the circuit breaker box. Then reset the control
to the desired setting.
A
BElectrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
77"
(196 cm)
6"
(15.2 cm)
6"
(15.2 cm)
24"
(60.96 cm) min.
6"
(15.2 cm)
1"
(2.54 cm)
80" - 90"
(203-229 cm)
83¹⁄2" (212.1 cm) min.
84³⁄4" (215 cm) max.
to bottom of solid soffit24"
Width
(see chart following)
Dimension

7
Water Supply Requirements
IMPORTANT:
■All installations must meet local plumbing code requirements.
■Connect to potable water supply only
■The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. The water supply line, however, must come up through
the oor in the gray shaded area shown.
NOTE: If the water shutoff valve is in the back wall behind the
refrigerator, it must be at an angle so that the tube is not
kinked when the refrigerator is pushed into its nal location.
■If the water shutoff valve is not in the cabinets, the plumbing
for the water line can come through the oor. A 1/2" (12.7 mm)
hole for plumbing should be drilled at least 6" (15.2 cm) from
the right-hand or left-hand side cabinet or panel. On the oor,
the hole should be no more than 1" (2.54 cm) away from the
back wall. See “Connect the Water Supply.”
■If additional tubing is needed, use copper tubing and check
for leaks. Install the copper tubing only in areas where the
household temperatures will remain above freezing.
■Do not use a piercing-type or 3/16" (4.76 mm) saddle valve
which reduces water ow and also clogs more easily.
NOTE: Your refrigerator dealer has a kit available with a
1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
Water Pressure
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, call a
licensed, qualied plumber.
NOTE: If the water pressure is less than what is required, the ow
of water from the water dispenser could decrease or ice cubes
could be hollow or irregular shaped. If you have questions about
your water pressure, call a licensed, qualied plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of
a reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi
(207 and 827 kPa).
If a reverse osmosis water ltration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40
to 60 psi (276 to 414 kPa):
■Check to see whether the sediment lter in the reverse
osmosis system is blocked. Replace the lter if necessary.
■Allow the storage tank on the reverse osmosis system to rell
after heavy usage.
■If your refrigerator has a water lter, it may further reduce
the water pressure when used in conjunction with a reverse
osmosis system. Remove the water lter cartridge.
If you have questions about your water pressure, call a licensed,
qualied plumber.
Tipping Radius
Be sure there is adequate ceiling height to stand the refrigerator
upright when it is moved into place.
■The dolly wheel height must be added to the tipping radius
when a dolly is used.
■If needed, the tipping radius can be reduced. See “Reduce
Tipping Radius.”
Side Tipping Radius
The side tipping radius varies depending upon the width of the
model. Use the chart provided to determine the side tipping
radius.
NOTE: Tip on side only.
Model Tipping Radius A
42 93" (236.2 cm)
48 96" (243.8 cm)
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
A
6"
(15.2 cm)
6"
(15.2 cm)
6"
(15.2 cm)
24"
(60.96 cm) min.
1"
(2.54 cm)

8
Product Dimensions
Side View
■The depth from the front of the top grille to the back of the
refrigerator cabinet is 25³⁄8" (64.5 cm).
■The power cord is 84" (213 cm) long.
■The water line attached to the back of the refrigerator is
5 ft (1.5 m) long.
■Height dimensions are shown with leveling legs extended
1/8" (3 mm) below the rollers.
*When leveling legs are fully extended to 1¹⁄4" (3.2 cm) below
rollers, add 1¹⁄8" (2.9 cm) to the height dimensions.
Top View
Model A B
42 Euro-Style 41" (104.1 cm) 2¹⁄8" (5.3 cm)
48 Euro-Style 47" (119.4 cm) 2¹⁄8" (5.3 cm)
42 Pro-Style®41" (104.1 cm) 26⁄8" (6.67 cm)
48 Pro-Style®47" (119.4 cm) 26⁄8" (6.67 cm)
Front View
■Width dimensions were measured from trim edge to trim
edge.
■Height dimensions are shown with leveling legs extended
1/8" (3 mm) below the rollers.
Model Tipping Radius A
42 42¹¹⁄32" (107.5 cm)
48 48¹¹⁄32" (122.8 cm)
*When leveling legs are fully extended to 1¹⁄4" (3.2 cm) below
rollers, add 1¹⁄8" (2.9 cm) to the height dimensions.
Door Swing Dimensions
The location must permit both doors to open to a minimum of
90°. Allow 4¹⁄2" (11.4 cm) minimum space between the side of the
refrigerator and a corner wall.
A
B
A
(see chart following)
84" (213.4 cm)
Power Cord
25³⁄8"
(64.5 cm)
23¹⁄2"
(59.7 cm)
*83³⁄8"
(211.8 cm)
*83³⁄8"
(211.8 cm)
25³⁄8"
(64.5 cm)
*3¹⁄2" (8.9 cm)

9
NOTE: More clearance may be required if you are using overlay
panels, custom handles, or extended handles.
To adjust the door swing, see “Adjust Doors.”
42" (106.7 cm) Models
Model A B
Pro-Style®10³/4" (27.11 cm) 14¹/4" (36.11 cm)
Euro 10¹/4" (25.87 cm) 13³/4" (34.88 cm)
48" (121.9 cm) Models
Model A B
Pro-Style®12³/16" (30.84 cm) 16¹/4" (41.16 cm)
Euro 115/8" (29.43 cm) 15¹¹/16" (39.75 cm)
Custom Side Panels
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type
of installation you are planning.
NOTES:
■The dimensions shown are actual product dimensions and
may not reect the needed panel installation dimensions.
■The side panel should be a minimum of 1/2" (1.27 cm)
thick to avoid warping.
■If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on rear wall.
Side Trim
Installation Dimensions (Option 1)
1. Measure the distance from point A (as shown) to the back
wall. Add 1/16" (1.6 mm) to this measurement to allow the
side panel to t into the trim.
2. If the panel is more than 11/32" (8.7 mm) thick, route the front
edge to allow the side panel to t into the trim.
Installation Dimensions (Option 2)
1. Measure the distance from point A (as shown) to back wall.
2. Route the front edge of the support board or attach a
3/8"(9.5 mm) board to hold the panel in the cabinet side trim.
A
A
AB
411⁄2"
(105.4 cm)
2319⁄32"
(59.9 cm)
2319⁄32"
(59.9 cm)
2317⁄32"
(59.8 cm)
2317⁄32"
(59.8 cm)
2315⁄32"
(59.6 cm)
2315⁄32"
(59.6 cm)
5/8"
(15.7 cm)
9/16"
(13.9 mm)
1/2"
(12.2 mm)
11/16"
(18.0 mm)
477⁄8"
(121.6 cm)
371⁄4"
(94.6 cm)
413⁄8"
(105.1 cm)
90°
90°
110°
110°
130°
130°
44"
(111.8 cm)
B
A
513⁄8"
(130.5 cm)
437⁄8"
(111.4 cm)
39"
(99.1 cm)
90°
90°
110°
110°
130°
130°

10
INSTALLATION
INSTRUCTIONS
Unpack the Refrigerator
IMPORTANT:
■Do not remove the lm covering until the refrigerator is in its
operating location.
■All four leveling legs must contact the oor to support and
stabilize the full weight of the refrigerator.
■Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating location.
1. Remove and save the literature package bag taped to the side
of the refrigerator and the parts bag behind the grille. Remove
the four brackets (two on each side) that attach the shipping
base to the refrigerator bottom.
NOTE: Do not remove tape and door bracing until the
refrigerator is in its nal location.
2. If necessary, reduce the tipping radius. See “Tipping Radius”
for ceiling height requirements or “Reduce Tipping Radius”
for step-by-step instructions. If you do not need to reduce the
tipping radius, proceed to “Move the Refrigerator into House.”
Reduce Tipping Radius
(if required)
Before bringing the refrigerator into the home, be sure there is
adequate ceiling height to stand the refrigerator upright. See
“Tipping Radius” in the “Installation Requirements” section for
more information.
If you do not have adequate ceiling height to stand the refrigerator
upright, the tipping radius can be reduced by removing the top
grille and side trims (see the following chart).
Model Reduced Tipping Radius
42 90¹⁄2" (229.9 cm)
48 91¹⁄4" (231.8 cm)
1. Grasp both ends of the top grille.
2. Push the top grille straight up; then pull straight out. Lay the
grille on a soft surface.
3. Remove the 6 screws attaching each cabinet side trim to the
refrigerator and remove the side trims.
Move the Refrigerator into House
1. Place an appliance dolly under the left side of the refrigerator
as shown. Place the corner posts from the packing materials
over the trims and handles as appropriate to avoid damage.
Slowly tighten the strap.
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
B BA
A. Top grille
B. Cabinet side trim
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.

11
NOTE: Pass the dolly strap under the handles.
2. Place pieces of the shipping carton on the oor when rolling
the dolly and refrigerator into the house. Move the refrigerator
close to the built-in opening.
3. Place top of cardboard carton or plywood under refrigerator.
4. Stand the refrigerator up. First, place the left bottom edge of
the refrigerator on the oor, stand the refrigerator upright and
then lower the right-hand side of the refrigerator to the oor.
5. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.
Install Anti-Tip Boards
IMPORTANT:
■To avoid tipping during use, the solid soft must be within
1" (2.5 cm) maximum above the refrigerator. If the solid soft
is higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
■It is recommended that board(s) be installed before the
refrigerator is installed.
■Board(s) must be long enough to fully cover the width of the
compressor cover.
■Locate the board(s) so the bottom surface(s) of the board(s) is
(are) 84" (213 cm) from the oor.
■During installation, raise the refrigerator up so there is
1/4" (6.35 mm) maximum between the top of the refrigerator
and the bottom of the anti-tip board(s). Do not crush the
compressor cover when raising the rear leveling legs.
NOTE: The foam gasket, on top of the compressor cover, will
compress to t under the anti-tip board(s). There is no need to
trim the gasket.
To Install Anti-tip Boards
1. Mark the stud locations on rear wall.
2. Securely attach two 2" x 4" x 32" (5 cm x 10 cm x 81 cm)
boards to wall studs behind refrigerator. Use six
#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws
must be screwed into the studs at least 1½" (3.8 cm). The
boards must overlap the compressor cover.
Connect the Water Supply
Read all directions before you begin.
IMPORTANT:
■If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
■Connect to potable water supply only.
Connect to Water Line
Parts Needed
■Minimum 7 ft (2.13 m) exible, codes-approved water supply
line
Style 1—Shutoff Valve Connection
NOTE: If your water line connection does not look like Style 1,
see “Style 2—Copper Line Connection.”
1. Unplug refrigerator or disconnect power supply.
IMPORTANT:
■There is not enough clearance to achieve a ush installation
if a water shutoff valve is located in the wall behind the
refrigerator. The water shutoff should be located in the base
cabinet on either side of the refrigerator.
■Before attaching the tubing to shutoff valve, ush the main
water supply line to remove particles and air in the water line.
Allow enough ow so that water becomes clear. Flushing the
water line may help avoid lters and/or water valves from
becoming clogged.
BA
C
2" (5 cm)
D
A. Center board 1/4" (6.35 mm)
max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x
10 cm x 81 cm) boards
C. Attach to studs with six
#8 x 3" (7.6 cm) screws
D. Compressor cover
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
2" (5 cm)

12
2. Connect the exible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve as shown.
3. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
4. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Style 2—Copper Line Connection
NOTE: If there is a water supply line that meets the specications
in “Water Supply Requirements,” proceed to “Connecting to
Refrigerator.” If not, use the following instructions to connect to
the household cold water supply.
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2" to 1¹⁄4" (1.3 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■Make sure it is a cold water pipe.
■Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and keep normal sediment from collecting in the
valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the refrigerator to the water pipe.
Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm)
O.D. (outside diameter) copper tubing. Be sure both ends of
copper tubing are cut square.
5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten.
IMPORTANT: Before attaching the tubing to shutoff valve, ush
the main water supply line to remove particles and air in the water
line. Allow enough ow so that water becomes clear. Flushing
the water line may help avoid lters and/or water valves from
becoming clogged.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten
the clamp or the sleeve. This will crush the copper tubing.
8. Turn off the shutoff valve on the water pipe. Coil the copper
tubing.
9. Connect the exible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve.
10. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
11. Check for leaks around the saddle valve. Tighten any nuts or
connections (including connections at the valve) that leak.
Connect to Refrigerator
Parts Supplied
■1/4" to 1/4" (6.35 mm to 6.35 mm) male-to-male coupling (on
some models)
NOTE: The exible, codes-approved water supply line should
connect to the supply valve through the oor.
1. Unplug the refrigerator or disconnect power.
2. Connect the 7 ft (2.13 m) exible codes-approved water tube
to the water supply valve.
3. Flush the main water supply line to remove particles and air in
the water line. Allow enough ow so that water becomes clear
4. Tape the 7 ft (2.13 m) exible codes-approved water supply
line to the oor, 7" (17.78 cm) from the left side of the
refrigerator. Tape along the length of the tubing, which will
allow it to pass beneath the refrigerator without interference.
NOTE: Allow a minimum of 26" (66.04 cm) of exible codes-
approved water supply line to be loose at the front of the
refrigerator for connecting to the refrigerator.
A
B
C
A. Bulb
B. Nut
C. Water tubing
A
B
C
DEF
G
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
6"
(15.2 cm)
6"
(15.2 cm)
1"
(2.54 cm)
7"
(17.78 cm)

13
5. Connect the 7 ft (2.13 m) exible codes-approved water
supply line to the refrigerator.
NOTE: If the main water shutoff valve is behind the
refrigerator, a secondary water shutoff valve may be installed
in line with the water supply line at the front of the product.
Overmold Coupling (on some models)
Discrete Coupling (on some models)
6. Turn on the water supply valve and check all connections for
leaks.
Plug in Refrigerator
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualied person. Do
not use a cord that shows cracks or abrasion damage along its
length or at either the plug or connection end.
1. Set control switch at top of cabinet to the OFF position.
2. Plug into a grounded 3 prong outlet.
Move Refrigerator to Final Location
IMPORTANT: To avoid oor damage, make sure levelers are
raised (not touching oor) and refrigerator is on rollers before
moving.
1. Place top of cardboard carton or plywood under refrigerator.
Remove dolly.
2. Do not remove lm or cover.
3. Move the refrigerator straight back and evenly into the
opening. Be sure that the refrigerator side trims are not
interfering with the door opening. Also, be sure that the water
tubing is not kinked and the power supply cord is on top of
the refrigerator.
AB C
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
A
B
CD
EFG
A. Household water line
B. Nut (purchased)
C. Ferrule (purchased)
D. Coupling
E. Bulb
F. Nut
G. Refrigerator water tubing
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.

14
Level and Align Refrigerator
IMPORTANT: All four leveling legs must contact the oor to
support and stabilize the full weight of refrigerator. Rollers are for
moving the refrigerator, not for permanent support.
After moving the refrigerator to its nal location:
1. Use a 5/16" socket driver to turn the leveling bolts clockwise
to extend the legs to the oor as shown. The rollers should be
off the oor.
2. Adjust the leveling legs to level and align the refrigerator from
left to right and front to back so that the refrigerator is level
and aligned with the cabinetry. The cabinetry surface must be
plumb for the ideal t of the refrigerator side trim.
3. Continue adjusting all of the leveling legs to raise the
refrigerator until the top is within at least 1" (2.54 cm) of the
top soft.
NOTE: If an anti-tip board has been used, adjust the leveling
legs until the top of the refrigerator is within 1/4" (6.35 mm) of
the bottom of the anti-tip board as shown. Do not crush the
compressor cover.
IMPORTANT: Adjust in small increments to keep from damaging
the cabinet trim and causing problems with the door alignment or
top grille t. To avoid damage to the cabinet or leveling legs, do
not apply more than 50 inch-pounds (5.65 Nm) of torque to the
leveling bolts. The leveling legs can be extended to a maximum of
1¹⁄4" (3.18 cm) below the rollers.
Adjust Doors
Door Height Adjustment
Use the following steps to adjust the door height, up or down,
after the doors have been leveled.
1. Open the freezer or refrigerator door and locate the bottom
hinge.
2. Remove the door stop screw from the bottom side of the hinge
with a 3/8" open end wrench.
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
A B
A
B
A. Rear leveling bolt
B. Front leveling bolt
BA
C
D
A. Center board 1/4" (6.35 mm) max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards
C. Attach to studs with six #8 x 3" (7.6 cm) screws
D. Compressor cover
ABC
A. Bushing
B. Door stop screw
C. Locking plate
1/4"(6 mm)
max.
2" (5 cm)

15
3. Remove the locking plate as shown.
4. Using a 1/2" open end wrench, turn the bushing located
underneath the bottom of the hinge.
■Turn the bushing to the left to lower the door.
■Turn the bushing to the right to raise the door.
5. After adjusting, check the doors to make sure they are even
across the top and bottom. If the doors are not even, continue
to turn the bushing to adjust the door height.
6. Replace the locking plate.
7. Turn the bushing slightly to align the hinge and locking plate
screw holes.
8. Replace the door stop screw or screws and tighten.
9. Recheck to make sure the doors are aligned and even.
Door Swing Adjustment
1. Check that the refrigerator door can open freely. If the door
opens too wide, remove the door stop screw or screws
(depending on your model) from the bottom hinge. See “Door
Height Adjustment” earlier in this section.
2. Hold the door open to a position that is less than 90°.
3. Replace the door stop screw or screws in the bottom hinge
and tighten.
Door-to-Door or Door-to-Refrigerator Trim Adjustment
1. Loosen, but do not remove, the four Torx†27 at-head
mounting screws. Remove and discard the two 1/4" hex-head
mounting screws.
2. Adjust the top hinge of either door to align it with the other
door or the refrigerator trim.
†TORX is a trademark of Acument Intellectual Properties, LLC
3. Tighten the four Torx† 27 at-head mounting screws to a
torque of approximately 100 inch-pounds (11.3 Nm).
Install Side Panel
If the built-in area depth is 25" (63.5 cm) or more, the side panels
can be installed inside the side trim or attached to the outside of
the side trim.
IMPORTANT: JennAir is not responsible for the removal or
addition of molding or decorative panels that would not allow
access to the refrigerator for service.
1. For the inside side trim piece, slide the front edge of the routed
side panel into the trim piece.
2. Nail the rear edge of the panel to the support board.
Install Base Grille
There are two pieces to the base grille to allow for a custom t: the
base grille itself and the skirt. The skirt can be added to the base
grille in order to extend it all the way to the oor.
1. To see whether the skirt is needed, place the base grille into
position. Do not attach the base grille to the refrigerator.
Measure the distance between the bottom of the base grille
and the oor. The gap must be a minimum of 1/2" (1.27 cm) in
order to add the skirt.
NOTE: If the gap measures less than 1/2" (1.27 cm), skip steps
3 and 4 of the instructions, and install the base grille only.
2. Remove the lm from the base grille.
AB C
A. 130°
B. 110°
C. 90°
A
B
A. Torx 27 at-head mounting screws
B. 1/4" hex-head mounting screws
A
B
A. Support board (mounted to back wall)
B. Cab side trim

16
3. Snap the skirt onto the base grille.
4. Trim the skirt by scoring the proper “V” groove with a utility
knife. Break the skirt at the score line.
5. Using the two screws, attach the base grille assembly to the
refrigerator as shown.
NOTE: Drive in the right side screw rst.
Complete Installation
1. Turn the water supply line valve to the “Open” position.
2. Turn the refrigerator switch to the ON position. See “Power
On/Off Switch” in the Use & Care Guide for instructions. Wait a
few minutes. Check the water line connections for leaks.
3. Remove all boxes, parts packages and packing materials from
the interior of the refrigerator. See the “Cleaning” section in
the Use & Care Guide for instructions. Remove the lm and
cardboard from the grille and doors or door frame, depending
on your model.
4. Install the shelves and bins in the refrigerator and freezer
compartments.
5. The controls are preset at the factory to the midpoint setting.
Make sure the compressor is operating properly and that all
the lights are working.
6. Flush the water system before use. See “Water System
Preparation.”
To get the most efcient use from your new built-in refrigerator,
read the Use & Care Guide. Keep Installation Instructions and Use
& Care Guide near the built-in refrigerator for easy reference.
Water System Preparation
Please read before using the water system.
IMPORTANT: After connecting the refrigerator to a water source
or replacing the water lter, follow the steps below to make sure
that the water system is properly cleaned. This will ush air from
the lter and water dispensing system, and prepare the water lter
for use.
NOTE: If your model has a base grille lter system, make sure the
base grille lter is properly installed and the cap is in the horizontal
position.
1. Open the freezer door and turn off the ice maker. The On/Off
switch is located on the top right side of the freezer
compartment. Move the switch to the OFF (right) setting as
shown.
2. Use a sturdy container to depress and hold the water
dispenser lever for 5 seconds, then release it for 5 seconds.
Repeat until water begins to ow. Once water begins to ow,
continue depressing and releasing the dispenser lever
(5 seconds on, 5 seconds off) until a total of 3 gal. (12 L) has
been dispensed. This will ush air from the lter and water
dispensing system, and prepare the water lter for use.
Additional ushing may be required in some households.
NOTE: As air is cleared from the system, water may spurt out
of the dispenser.
3. Open the freezer door and turn on the ice maker. Move the
switch to the ON (left) position.
NOTES:
■Allow 24 hours to produce the rst batch of ice.
■Discard the rst three batches of ice produced.
■Allow 3 days to completely ll ice container.
■Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
A
B
A. Base grille
B. Skirt
A
A.“V” groove
A
A. Screws (2)
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.

17
SÉCURITÉ DU RÉFRIGÉRATEUR
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
AVERTISSEMENT
Risque de basculement
Le réfrigérateur est lourd au sommet et bascule
facilement lorsqu'il n'est pas complètement installé.
Garder les portes fermées avec un ruban adhésif
jusqu'à l'installation complète du réfrigérateur.
Utiliser deux ou plus de personnes pour déplacer et
installer le réfrigérateur.
Le non-respect de ces instructions peut causer un
décès ou une blessure grave.

18
MODÈLES DE 42"
Conception Euro Style
Comprend des portes en acier inoxydable avec poignées
porte-serviettes.
JS42SSDUDE
Conception Pro-Style®
Portes avec habillage en acier inoxydable et poignées Pro-Style®
avec surface de saisie à texture gravée (losanges).
JS42PPDUDE
MODÈLES DE 48"
Conception Euro Style
Comprend des portes en acier inoxydable avec poignées
porte-serviettes.
JS48SSDUDE
Conception Pro-Style®
Portes avec habillage en acier inoxydable et poignées Pro-Style®
avec surface de saisie à texture gravée (losanges).
JS48PPDUDE

19
EXIGENCES D’INSTALLATION
Outils et pièces
IMPORTANT:
■Installateur: Remettre les instructions d’installation au
propriétaire.
■Propriétaire: Conserver les instructions d’installation pour
référence ultérieure. Conserver ces instructions d’installation pour
consultation par l’inspecteur local des installations électriques.
Outils requis:
Rassembler les outils et pièces nécessaires avant d’entreprendre
l’installation. Lire et observer les instructions fournies avec chacun
des outils de la liste ci-dessous.
■Perceuse sans l ■Tourne-écrou de 11/32"
■Forets
■Clés à molette (2)
■Clés à fourche de 3/8" et 1/2"
■Tournevis à tête
cruciforme
■Clé hexagonale de 5/32"
■Petit niveau ■Tournevis à douille de 1/4"
et5/16"
■Chariot pour appareil
ménager
■Ruban à mesurer
■Tournevis Torx†T27 ■Couteau utilitaire
Pièces nécessaires :
■Vis à bois n° 8 x 3" (7,6 cm) (il peut être nécessaire d’utiliser
des vis plus longues) (6)
■Planche(s) de bois de 2" x 4" x 32" (5 cm x 10 cm x 81 cm)
(1ou 2)
■Dans le cas d’un raccordement direct de la canalisation d’au
au tube de cuivre et non à un robinet d’arrêt, on doit disposer
d’un raccord à compression de 1/4" (6,35 mm) avec virole et
raccord union.
Exigences d’emplacement
Le réfrigérateur peut être encastré dans une ouverture entre les
armoires ou installé à l’extrémité d’une enlade d’armoires en
utilisant un panneau latéral pour encadrer le réfrigérateur.
IMPORTANT: Cet appareil est conçu pour un usage domestique,
à l’intérieur uniquement.
Cet appareil est destiné à un usage domestique et à d’autres
usages similaires comme:
■Espace de cuisine pour personnel de boutiques, bureaux et
autres environnements professionnels.
■Résidences fermières et utilisation par les clients d’hôtels, de
motels et d’autres types de résidences.
■Environnements de type chambres d’hôtes.
■Banquets et autres utilisations non commerciales semblables.
■Observer les dispositions de tous les codes et règlements en
vigueur.
■Il est conseillé de ne pas installer le réfrigérateur près d’un four,
d’un radiateur ou de toute autre source de chaleur.
■Ne pas installer l’appareil dans un endroit où la température
pourrait descendre sous 55°F (13°C).
■Le plancher doit pouvoir supporter le poids du réfrigérateur,
soit plus de 600 lb (272 kg) incluant les panneaux de porte et
le contenu du réfrigérateur.
■La hauteur libre sous plafond doit être sufsante pour
permettre le basculement de chaque côté.
Voir “Rayon de basculement” plus loin dans cette section.
■L’emplacement doit permettre l’ouverture complète de la porte.
Voir “Dimensions pour le pivotement des portes”.
■L’emplacement d’installation doit permettre la dépose de la
grille supérieure.
Voir “Dimensions de l’ouverture d’encastrement”.
Dimensions de l’ouverture
■Pour éviter le basculement pendant l’utilisation, le softe massif
doit se trouver à 1" (2,5cm) maximum au-dessus du réfrigérateur.
Si le softe massif se trouve à plus de 1" (2,5 cm) ou si un softe
n’est pas disponible, le réfrigérateur doit être arrimé.
Si des planches antibasculement sont nécessaires, ils doivent
être installés sur les montants du mur arrière de sorte que le
bas du poteau antibasculement se trouve à 84"(213 cm) du
sol. Voir “Installation des planches antibasculement” pour plus
d’informations.
REMARQUES:
■Un dégagement de 1/2" (1,3 cm) doit être maintenu au-
dessus de la grille supérieure pour que la grille supérieure
puisse être enlevée.
■Ne pas retirer le joint en mousse du sommet du couvercle
du compresseur sauf s’il est nécessaire de le retirer pour
installer l’appareil sous un softe. Retirer le joint peut
affecter les performances de refroidissement.
■Si l’appareil est installé sous un softe massif, relever les
pieds de nivellement après l’installation pour que le joint
soit solidement appuyé contre le softe.
■Une prise électrique à trois broches avec mise à la terre doit
être placée à une distance dénie des armoires de droite ou
du panneau situé à l’extrémité. Voir le tableau sous l’illustration
pour connaître le nombre de pouces à respecter pour votre
modèle. Voir les “Spécications électriques” pour plus de
renseignements.
Risque d'explosion
Garder les matériaux et les vapeurs inflammables, telle
que l'essence, loin du réfrigérateur.
Le non-respect de cette instruction peut causer
un décès, une explosion ou un incendie.
AVERTISSEMENT
B
A
A. Joint d’étanchéité
B. Couvercle du compresseur
1/2"
(1,3 cm)
†TORX est une marque déposée d’Acument Intellectual Properties, LLC.

20
■Le robinet d’arrêt d’eau doit être situé dans l’armoire inférieure
d’un côté ou l’autre du réfrigérateur, ou à un autre endroit
facilement accessible. Si le robinet d’arrêt ne se trouve pas
dans les armoires, la plomberie d’arrivée d’eau peut provenir
du plancher. Voir “Spécications de l’alimentation en eau”
pourplus de renseignements.
Modèle Largeur A
(telle qu’indiquée
ci-dessus)
Dimension B
(telle qu’indiquée
ci-dessus)
42 41¹⁄2" à 41³⁄4"
(105,4 cm à 106,1 cm)
7¹⁄2" (19,1 cm)
48 47¹⁄2" à 47³⁄4"
(120,7 cm à 121,3 cm)
13¹⁄2" (34,3 cm)
REMARQUE: Le revêtement de sol sous le réfrigérateur doit
se trouver au même niveau que le sol de la pièce. L’avant des
armoires doit être d’aplomb.
Spécifications électriques
Avant de placer le réfrigérateur à son emplacement nal, ilest
important de s’assurer d’avoir le raccordement électrique
approprié.
Si le cordon d’alimentation est endommagé, il doit être remplacé
par le fabricant, son agent de service ou toute autre personne
également qualiée. Ne pas utiliser un cordon craquelé ou qui
présente des dommages d’abrasion sur la gaine, la che ou
l’extrémité de connexion.
Méthode recommandée de liaison à la terre
Chaque appareil doit être alimenté par un circuit à 115V CA à
60Hz relié à la terre et protégé par un fusible de 15A ou 20A.
Il est recommandé d’utiliser un circuit distinct pour alimenter
le réfrigérateur uniquement. Utiliser une prise de courant dont
l’alimentation ne peut pas être interrompue par un interrupteur.
Nepas utiliser de rallonge.
IMPORTANT: Si ce produit est connecté à une prise protégée par
un disjoncteur de fuite à la terre, un déclenchement intempestif
peut se produire et causer une perte de refroidissement.
Laqualité et la saveur des aliments risquent d’être affectées.
Si un déclenchement intempestif se produit et si les aliments
semblent de piètre qualité, jeter le tout.
REMARQUE: Avant d’exécuter tout type d’installation ou de
nettoyage, retirer la grille supérieure et mettre l’interrupteur général
d’alimentation à OFF (arrêt) ou déconnecter le courant au boîtier
de disjoncteurs.
Lorsque vous avez terminé, mettre l’interrupteur général
d’alimentation à ON (marche) ou rétablir le courant au boîtier de
disjoncteurs. Puis placer de nouveau la commande au réglage désiré.
A
B
AVERTISSEMENT
Risque de choc électrique
Brancher sur une prise à 3 alvéoles reliée à la terre.
Ne pas enlever la broche de liaison à la terre.
Ne pas utiliser un adaptateur.
Ne pas utiliser un câble de rallonge.
Le non-respect de ces instructions peut causer
un décès, un incendie ou un choc électrique.
77"
(196 cm)
6"
(15,2 cm)
6"
(15,2 cm)
24"
(60,96 cm) min.
6"
(15,2 cm)
1"
(2,54 cm)
80" - 90"
(203-229 cm)
83¹⁄2" (212,1 cm) min. 84³⁄4"
(215 cm) max. jusqu’au
bas du soffite massif 24"
Largeur
(voir le tableau suivant)
Dimension