Jenn-Air JSC24C8EAM00 User manual

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,
please visit our website at www.jennair.com for additional information. If you still need assistance, call us at 1-800-536-6247.
In Canada, visit our website at www.jennair.ca or call us at 1-800-807-6777.
You will need your model and serial number, located on the inside wall of the refrigerator compartment.
Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espa_ol, o para obtener informaci6n adicional acerca de
su producto, visite: www.jennair.com.
Necesitara su nQmerode modelo y de serie, ubicado en el interior del compartimiento del refrigerador.
TableofContents/Tabledes mati6res
REFRIGERATOR SAFETY ..................................................................... 2
Proper Disposal of Your Old Refrigerator ........................................... 2
REFRIGERATOR USE ........................................................................... 3
Install Air Filter ..................................................................................... 3
Install Produce Preserver .................................................................... 3
Using the Controls .............................................................................. 4
Convertible Drawer Temperature Control .......................................... 6
Crisper Humidity Control .................................................................... 6
Chilled Door Bin .................................................................................. 6
Water and Ice Dispensers ................................................................... 6
Ice Maker and Storage Bin ................................................................. 7
Water Filtration System ....................................................................... 8
REFRIGERATOR CARE ......................................................................... 9
Cleaning .............................................................................................. 9
Changing the Light Bulbs ................................................................... 9
TROUBLESHOOTING .......................................................................... 10
Refrigerator Operation ...................................................................... 10
Temperature and Moisture ............................................................... 11
Ice and Water .................................................................................... 11
ACCESSO RIES .................................................................................... 12
WATER FILTER CERTIFICATIONS .................................................... 12
PERFORMANCE DATA SHEET .......................................................... 13
SI_CURITI_ DU RI_FRIGI_RATEUR ................................................... 16
Mise au rebut appropriee de votre vieux refrig6rateur ..................... 17
UTILISATION DU RI_FRIGI_RATEUR ................................................. 17
Installation du filtre & air (sur certains modeles) ............................... 17
Installer le sachet de conservation pour produits frais .................... 18
Utilisation des commandes .............................................................. 19
Commande de temperature dans le tiroir convertible ..................... 21
Reglage de I'humidit_ dans le bac & legumes ................................. 21
Compartiment fratcheur dans la porte ............................................. 21
Distributeurs d'eau et de glagons ..................................................... 21
Machine &glagons et bac d'entreposage ........................................ 23
Syst_me de filtration de I'eau ........................................................... 24
ENTRETIEN DU RleFRIGleRATEUR ................................................... 25
Nettoyage .......................................................................................... 25
Remplacement des ampoules d'eclairage ....................................... 25
DlePANNAGE ........................................................................................ 26
Fonctionnement du refrig_rateur ...................................................... 26
Temperature et humidit6 .................................................................. 27
Glagons et eau .................................................................................. 27
ACCESSOIRES .................................................................................... 28
FEUILLE DE DONNI_ES SUP LA PERFORMANCE .......................... 29
GARANTIE ............................................................................................ 30
WARRANTY .......................................................................................... 14
W10487490A

REFRIGERATORSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all parts and panels before operating.
• Remove doors from your old refrigerator.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
• Use two or more people to move and install refrigerator.
• Disconnect power before installing ice maker (on ice maker
kit ready models only).
• Use a sturdy glass when dispensing ice (on some models).
• Do not hit the refrigerator glass doors (on some models).
SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
Proper DisposalofYourOld Refrigerator
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous
- even if they will sit for "just a few days." Ifyou are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
• Takeoff the doors.
• Leave the shelves in place so that children may not easily
climb inside.
important information to know about disposal of
refrigerants:
Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
2

A
REFRIGERATORUSE
(o_ some modes}
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use. On some models,
the air filter is already installed at the factory.
The air filter reduces the buildup of odors. This helps to maintain a
cleaner environment inside the refrigerator.
Installing the Air Filter (on some models)
The filter should be installed behind the vented door, which is
located (depending on your model) along either the rear or left
interior wall near the top of the refrigerator compartment.
1. Remove the air filter from its packaging.
2. Lift open the vented door.
3. Snap the filter into place.
Installing the Filter Status Indicator (on some models)
The filter comes with astatus indicator, which should be activated
and installed at the same time the air filter is installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator, until
the bubble pops to activate the indicator.
3. Lift open the vented air filter door. On some models, there are
notches behind the door.
4. On models with notches:
• Slide the indicator down into the notches, facing outward.
NOTE: The indicator will not easily slide into the notches
if the rear bubble has not been popped.
• Close the air filter door, and check that the indicator is
visible through the rectangular hole in the door.
On models without notches:
• Store the indicator in a visible place you will easily
remember - either inside the refrigerator, or elsewhere in
your kitchen or home.
Replacing the Air Filter
The disposable air filter should be replaced every 6 months, when
the status indicator has completely changed from white to red.
To order a replacement air filter, see "Accessories."
1. Remove the old air filter by squeezing in on the side tabs.
2. Remove the old status indicator.
3. Install the new air filter and status indicator using the
instructions in the previous sections.
(o_ssome modes}
On some models, your refrigerator's accessory packet includes a
Produce Preserver, which should be installed prior to use. On
some models, the Produce Preserver is already installed at the
factory.
The Produce Preserver absorbs ethylene, allowing the ripening
process of many produce items to slow down. As a result, certain
produce items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
Apples
Asparagus
Berries
Broccoli
Cantaloupe
Carrots
Citrus Fruit
Grapes
Lettuce
Pears
Spinach
Sensitivity to
Ethylene
High
Med.
Low
High
Med.
Low
Med.
Low
High
High
High
Ethylene
Production
Very High
Very Low
Low
Very Low
High
Very Low
Very Low
Very Low
Very Low
Very High
Very Low

Installing the Produce Preserver (on some models)
CAUTION: IRRITANT
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.
Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.
The Produce Preserver pouches should be installed in their
housing, which is located along an interior side wall of the crisper
or convertible drawer.
NOTE: For best performance, always use two pouches.
1. Remove the Produce Preserver pouches from their packaging.
FreshF1ow
produce preserver
CAUTION ATTENTION
IRRITANT IRRITANT
Read cautions on back Lire les mises en garde au dos,
2. Lift up on the housing in order to remove it from its mounting
tab along the wall.
3. Open the housing by pulling up and out on the back of the top
of the housing.
4. Place both pouches inside the housing, then snap the housing
back together.
5. Place the housing back on the mounting tab along the wall.
Installing the Status Indicator (on some models)
The Produce Preserver comes with a status indicator, which
should be activated and installed at the same time the pouch is
installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator, until
the bubble pops to activate the indicator.
3. Slide open the cap on the Produce Preserver housing.
4. Place the indicator in the top of the housing, facing outward.
5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.
NOTE: The cap will not easily close if the indicator's rear
bubble has not been popped.
Replacing the Produce Preserver (on some models)
The disposable pouches should be replaced every 6 months,
when the status indicator has completely changed from white to
red.
To order replacements, see "Accessories."
1. Remove the old pouches from the Produce Preserver housing.
2. Remove the old status indicator.
3. Install the new pouches and status indicator using the
instructions in the previous sections.
Jsnc Con t s s
The refrigerator and freezer controls are located on the dispenser
panel.
IMPORTANT: The display screen on the dispenser control panel
will turn off automatically and enter "sleep" mode when the
control buttons and dispenser pads have not been used for
2 minutes or more. While in "sleep" mode, the first press of a
control button will only reactivate the display screen, without
changing any settings. After reactivation, changes to any settings
can then be made. If no changes are made within 2 minutes, the
display will re-enter "sleep" mode.
• Touch any control button on the dispenser panel to activate
the display screen. The home screen will appear as shown.

Adjusting the Controls
For your convenience, your refrigerator and freezer controls are
preset at the factory. When you first install your refrigerator, make
sure that the controls are still set to the "mid-settings." The factory
recommended set points are 37°F (3°C) for the refrigerator and
0°F (-18°C) for the freezer.
IMPORTANT:
• Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a colder than
recommended setting will not cool the compartments any
faster.
If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
To view and adjust the set points, press and hold the TEMP
button for 3 seconds. When adjust mode is activated, adjusting
information will appear on the display screen.
NOTE: To view Celsius temperatures, press the OPTIONS button
when adjust mode is activated. To return the display setting to
Fahrenheit, press OPTIONS again.
• When adjust mode is activated, the display screen shows the
refrigerator set point and "FRIDGE" appears.
• Press the SELECT arrows to raise or lower the set point.
When you have finished viewing (and adjusting if desired) the
refrigerator set point, press TEMP to change the display to
show the freezer set point. When the zone has been changed,
"FREEZER" appears on the display screen.
• Press the SELECT arrows to raise or lower the set point.
• When you have finished viewing (and adjusting if desired) both
the refrigerator and freezer set points, press LIGHT to save the
settings.
NOTE: To exit without saving changes, allow about
60 seconds of inactivity and adjust mode will turn off
automatically.
When adjusting temperature set points, use the following chart as
a guide.
CONDITION: TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold REFRIGERATOR Setting
1° higher
REFRIGERATOR too warm REFRIGERATOR Setting
1° lower
FREEZER too cold FREEZER Setting
1° higher
FREEZER too warm /FREEZER Setting
Too little ice 1° lower
The set point range for the refrigerator is 33°F to 45°F (0°C to
7°C). The set point range for the freezer is -5°F to 5°F (-21°C to
-15°C).
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is
turned off.
• To turn cooling off, press and hold the OPTIONS and FILTER
buttons at the same time for 3 seconds.
IMPORTANT: To avoid unintentionally locking the dispenser
or changing other settings, be sure to press both buttons at
exactly the same time.
When cooling is off, "COOLING OFF" will appear on the
display screen.
Press and hold OPTIONS and FILTER for 3 seconds again to
turn cooling back on.
Additional Features
Speed Ice and Max Cold
The Speed Ice feature assists with temporary periods of heavy ice
use by increasing ice production over a 24-hour period.
The Max Cold feature assists with periods of heavy ice usage, full
grocery loads, or temporarily warm room temperatures.
• To turn on the Speed Ice feature, press OPTIONS.
"Speed Ice" will appear on the display screen.
The Speed Ice feature will remain on for 24 hours unless
manually turned off.
To turn on the Max Cold feature, press OPTIONS a second
time. The Speed Ice feature will turn off, and the Max Cold
feature will turn on. "Max Cold" will appear on the display
screen.
The Max Cold feature will remain on for 24 hours unless
manually turned off.
To turn on both the Speed Ice and Max Cold features at the
same time, press OPTIONS a third time. Both "Speed Ice" and
"Max Cold" will appear on the display screen.
Both features will remain on for 24 hours unless manually
turned off.
• To turn both features off, press OPTIONS a fourth time. Both
"Speed Ice" and "Max Cold" will disappear from the display
screen.
When Speed Ice and/or Max Cold are active, the temperature
displays will not change. After 24 hours, the refrigerator returns to
the previous temperature set points.
NOTE: If increased ice production is desired at all times, change
the freezer control to a lower setting. Setting the freezer to a
colder temperature may make some foods, such as ice cream,
harder.

DoorAjarAlarm
TheDoorAjarAlarmfeaturesoundsanalarmwhentherefrigerator
orfreezerdoorisopenfor5minutesandtheproductcoolingis
turnedon.Thealarmwillrepeatevery2minutes.Closeboth
doorstoturnitoff.Thefeaturethenresetsandwillreactivate
wheneitherdoorisleftopenagainfor5minutes.
NOTE:Tomutetheaudiblealarmwhilekeepingthedoorsopen,
suchaswhilecleaningtheinsideoftherefrigerator,pressany
buttononthecontrolpanel.Thealarmsoundwillbetemporarily
turnedoff,but"DoorAjar"willstillbedisplayedonthedispenser
controlpanel.
DisablingSounds
• Toturnoffallcontrolanddispensersounds,pressandhold
LIGHTandFILTERatthesametimefor3seconds.
• Toturnallsoundsbackon,pressandholdLIGHTandFILTER
atthesametimefor3secondsagain.
Dual Evaporator (on some models)
Some models come equipped with a dual sequential evaporation
system, which includes two separate evaporators for the
refrigerator and freezer compartments.
Dual evaporation results in higher humidity, which helps keep
foods in the refrigerator from spoiling as quickly and improves
food quality and freshness in the freezer due to decreased freezer
burn. In addition, the dual evaporation system helps keep food
smells in the refrigerator from transferring to ice in the freezer.
NOTE: The dual evaporation system is always activated when
your refrigerator is operating. You do not need to press any
buttons to turn it on.
S¢ ,,.cos _! ._t:_, ,...& ,.,Conf.4
(olq so _"e modes
The control can be adjusted to properly chill meats or vegetables.
The air inside the pan is cooled to avoid "spot" freezing and can
be set to keep meats at the National Livestock and Meat Board
recommended storage temperatures of 28° to 32°F (-2° to O°C).
To store meat:
Set the control to one of the three MEAT settings to store meat at
its optimal storage temperature.
To store vegetables:
Set the control to VEG to store vegetables at their optimal storage
temperatures.
NOTE: If food starts to freeze, move the control to the right (less
cold), toward the VEG setting. Remember to wait 24 hours
between adjustments.
(o_"so _"e modes
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.
h Doo[ Bi's,
Cool air from the freezer is directed to the refrigerator door bin
directly beneath the vents.
NOTE: The dairy compartment and can rack are not associated
with the Chilled Door Bin feature.
Chilled Door Bin Control
The chilled door bin control is located on the left-hand side of the
refrigerator compartment.
A--
A. Chilleddoor bin control
Slide the door chill control to the left to reduce the flow of cold
air to the bin and make it less cold.
Slide the door chill control to the right to increase the flow of
cold air to the bin and make it colder.
IMPORTANT: After connecting the refrigerator to a water source
or replacing the water filter, flush the water system. Use a sturdy
container to depress and hold the water dispenser pad for
5 seconds, then release it for 5 seconds. Repeat until water
begins to flow. Once water begins to flow, continue depressing
and releasing the dispenser pad (5 seconds on, 5 seconds off)
until a total of 3 gal. (12 L) has been dispensed. This will flush air
from the filter and water dispensing system, and prepare the
water filter for use. Additional flushing may be required in some
households. As air is cleared from the system, water may spurt
out of the dispenser.
NOTES:
• The dispensing system will not operate when the freezer door
is open.
• Allow 24 hours for the refrigerator to cool down and chill
water.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Wait 72 hours for full ice
production.
The display screen on the dispenser control panel will turn off
automatically and enter "sleep" mode when the control
buttons and dispenser pad have not been used for 2 minutes
or more. While in "sleep" mode, the first press of a control
button will only reactivate the display screen, without
changing any settings. After reactivation, changes to any
settings can then be made. If no changes are made within
2 minutes, the display will re-enter "sleep" mode.
The Water Dispenser
IMPORTANT:
• Dispense at least 1 qt (1 L) of water every week to maintain a
fresh supply.
• If the flow of water from the dispenser decreases, it could be
caused by low water pressure.
With the water filter removed, dispense 1 cup (237 mL) of
water. If 1 cup of water is dispensed in 8 seconds or less,
the water pressure to the refrigerator meets the minimum
requirement.
If it takes longer than 8 seconds to dispense 1 cup of
water, the water pressure to the refrigerator is lower than
recommended. See "Water Supply Requirements" or
"Troubleshooting" for suggestions.
6

To Dispense Water:
1. Press the SELECT arrows on the dispenser control panel, until
"Water" is selected.
2. Press a sturdy glass against the dispenser pad.
3. Remove the glass to stop dispensing.
The Ice Dispenser
Ice dispenses from the ice maker storage bin in the freezer when
the dispenser pad is pressed. To turn off the ice maker, see "Ice
Maker and Storage Bin."
Your ice maker can produce both crushed and cubed ice. Before
dispensing ice, select which type of ice you prefer by pressing the
SELECT arrows.
The display screen indicates which type of ice is selected.
m m _
m
CRUSHED CUBED
For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary insize.
When changing from crushed to cubed, a few ounces of crushed
ice will be dispensed along with the first cubes.
To Dispense Ice:
1. Make sure the desired type of ice is selected. To switch
between cubed and crushed, press the SELECT arrows.
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
2=
3=
Press a sturdy glass against the dispenser pad. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to the
pad in order to activate the ice dispenser. Pressing hard will
not make the ice dispense faster or in greater quantities.
Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for several seconds after
removing the glass from the pad. The dispenser may continue
to make noise for a few seconds after dispensing.
The Dispenser Light
When you use the dispenser, the light will automatically turn on.
If you want the light to be on continuously, you may choose either
ON or DIM.
ON: Press LIGHT to turn the dispenser light on. "On" will appear
on the display screen.
DIM: Press LIGHT a second time to select DIM mode. "Dim" will
appear on the display screen. The dispenser light will remain on,
but at a lower intensity.
OFF: Press LIGHT a third time to turn the dispenser light off.
The dispenser lights are LEDs that cannot be changed. If it
appears that your dispenser lights are not working, see
"Troubleshooting" for more information.
The Dispenser Lock
The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the refrigerator,
to the ice maker, or to the dispenser light. It simply deactivates the
controls and dispenser pad. To turn off the ice maker, see "Ice
Maker and Storage Bin."
• Press and hold LIGHT for 3 seconds to lock the dispenser.
"Dispenser Locked" will appear on the display screen.
• Press and hold LIGHT a second time to unlock the dispenser.
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The quality of your ice will be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener is operating properly and is well
maintained.
Do not use anything sharp to break up the ice in the storage
bin. This can cause damage to the ice container and the
dispenser mechanism.
Do not store anything on top of or in the ice maker or storage
bin.
Style I
Turning the Ice Maker On/Off:
The On/Oft switch can only be accessed when the ice storage bin
has been removed. The switch is located on the freezer door, on
the left side of the wall that surrounds the ice storage bin. See the
following section for bin removal instructions.
On Off
Ice Maker Control
To turn on the ice maker, slide the control to the ON (left)
position.
To manually turn off the ice maker, slide the control to the OFF
(right) position.

NOTE:Theicemakerhasanautomaticshutofftokeepthe
storagebinfromoverfillingduringnormaloperation.Theice
makersensorswillautomaticallystopiceproduction,butthe
controlwillremainintheON(left)position.
Removing and Replacing Ice Storage Bin:
1. Press down the release lever and tilt the bucket outward. Use
both hands to hold the base of the storage bin, then lift it up
and out.
Removing and Replacing Ice Storage Bin:
1. Pull the covering panel up from the bottom.
2. Lift the wire shutoff arm so it clicks into the OFF (up) position.
3. Lift up the front of the storage bin and pull it out.
A
A. Release lever
NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The
sensor cover ("flipper door"), located on the right wall of the
freezer door, stops the ice maker from producing ice if the
door is open or the storage bin is removed.
A. On/Off switch
B. Sensor cover
2. Replace the bin by sliding it onto the door, then tilting it back
into an upright position. The release lever will click when the
bin is securely in place.
Style 2
Turning the Ice Maker On/Off:
• Toturn ONthe ice maker,simply lowerthe wire shutoff arm.
• To manually turn off the ice maker, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click. Ice can still
be dispensed, but no more can be made.
NOTE: The ice maker has an automatic shutoff to keep the
storage bin from overfilling during normal operation. As ice is
made, the ice cubes will fill the ice storage bin, and the ice cubes
will raise the wire shutoff arm to the OFF (arm up) position. Do not
force the wire shutoff arm up or down.
4.
5.
Replace the bin by pushing it in all the way or the dispenser
will not work.
To restart ice production, push the wire shutoff arm down to
the ON position. Make sure the door is closed tightly.
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Water Filter Status Light
The water filter status light will help you know when to change
your water filter.
• When the dispenser control panel's water filter status display
changes to "ORDER," this tells you that it is almost time to
change the water filter cartridge.
• Replace the water filter cartridge when the water filter status
display changes to "REPLACE."
If water flow to your water dispenser or ice maker decreases
noticeably, change the filter sooner. The filter should be replaced
at least every 6 months, depending on your water quality and
usage.
• After changing the water filter, reset the status light by
pressing and holding the FILTER button for 3 seconds. When
the system is reset, the "ORDER" and "REPLACE" icons will
disappear from the display screen.
Changing the Water Filter
1. Locate the water filter in the top-right corner of the refrigerator
compartment.
2. Lift open the filter cover door. The filter will be released and
then eject as the door is opened.
8

3.
4=
When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
Take the new filter out of its packaging and remove the covers
from the O-rings. Be sure the O-rings are still in place after the
covers are removed.
5. With the arrow pointing up, align the new filter with the filter
housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
6. Close the filter cover door completely in order to snap the filter
into place. You may need to press hard.
7. Flush the water system. See "Water and Ice Dispensers."
REFRIGERATORCARE
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
3. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water.
Broken Glass Hazard
Do not hit refrigerator glass doors.
Protect glass surface and edges during installation or
removal of doors.
Failure to do so can result in serious eye injury or
minor cuts.
4=
5.
On some models, wash glass door panels with a clean
sponge or soft cloth and a mild detergent in warm water.
NOTE: Do not hit the glass with pots, pans, furniture, toys, or
other objects. Scratching, hitting, jarring or stressing the glass
may weaken its structure, causing an increased likelihood of
breakage at a later date.
There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
• Remove the base grille. See the "Door Removal"
instructions, either in the User Instructions or the separate
instruction sheet provided with your refrigerator.
• Use a vacuum cleaner with asoft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
• Replace the base grille when finished.
6. Plug in refrigerator or reconnect power.
ChcJnc n<s ....
NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with one of the same size, shape and wattage.
• The dispenser lights are LEDs that cannot be changed.
• On some models, the interior lights are LEDs that cannot
be changed.
• On some models, the interior lights require a 40-watt bulb.
1. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
3. Remove light bulb and replace with one of the same size,
shape and wattage.
4. Replace light shield when applicable.
5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call.
In the U.S.A., www.jennair.com In Canada, www.jennair.ca
The refrigerator will not operate
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power cord unplugged? Plug into a grounded 3 prong outlet.
Is outlet working? Plug in a lamp to see ifthe outlet is
working.
Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
Are controls on? Make sure the refrigerator controls are on.
See "Using the Controls."
New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The refrigerator may run
even longer if the room is warm, a large food load is added, doors
are opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
listed some normal sounds with an explanation.
• Buzzing -heard when the water valve opens to fill the ice
maker
•Clicking/Snapping - valves opening or closing
•Pulsating - fans/compressor adjusting to optimize
performance
• Rattling - flow of refrigerant, water line, or from items placed
on top of the refrigerator
Sizzling/Gurgling - water dripping on the heater during
defrost cycle
Popping - contraction/expansion of inside walls, especially
during initial cool-down
Water running - may be heard when ice melts during the
defrost cycle and water runs into the drain pan
Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.
The doors will not close completely
•Door blocked open? Move food packages away from door.
• Bin or shelf in the way? Push bin or shelf back in the correct
position.
The doors are difficult to open
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
•Are the gaskets dirty or sticky? Clean gaskets with mild
soap and warm water.
The refrigerator rocks and is not stable
What do I do if the refrigerator rocks and is not stable?
To stabilize the refrigerator, remove the base grille and lower
the leveling feet until they touch the floor. See the "Door
Removal" instructions, either in the User Instructions or the
separate instruction sheet provided with your refrigerator.
The lights do not work
Is alight bulb loose in the socket or burned out? See
"Changing the Light Bulbs."
Is the dispenser light set to OFF? On some models, the
dispenser light will operate only when a dispenser lever/pad is
pressed. If you want the dispenser light to stay on
continuously, set the dispenser light to ON, or (on some
models) NIGHT LIGHT or AUTO or HALF or DIM. See "Water
and Ice Dispensers."
Is the dispenser light set to NIGHT LIGHT or AUTO? On
some models, if the dispenser is set to the NIGHT LIGHT or
AUTO mode, be sure the dispenser light sensor is not
blocked. See "Water and Ice Dispensers."
10

Temperature is too warm
•New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
• Door(s) opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully
closed.
Large load of food added? Allow several hours for
refrigerator to return to normal temperature.
Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See "Using the Controls."
There is interior moisture buildup
NOTE: Some moisture buildup is normal. Clean with a dry cloth.
• Humid room? Contributes to moisture buildup.
• Door(s) opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully
closed.
Ice cs 'd
The ice maker is not producing ice or not enough ice
Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.
Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.
New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil. (This
does not apply to models with the ice maker mounted at the
top of the freezer door.)
Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
• Water shutoff valve not fully open? Turn the water shutoff
valve fully open.
•Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.
•Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
•Questions remain regarding water pressure? Call a
licensed, qualified plumber.
Off-taste, odor or gray color in the ice
•New plumbing connections? New plumbing connections
can cause discolored or off-flavored ice.
Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.
Odor transfer from food? Use airtight, moisture-proof
packaging to store food.
Are there minerals (such as sulfur) in the water? A water
filter may need to be installed to remove the minerals.
Is there a water filter installed on the refrigerator? Gray or
dark discoloration in ice indicates that the water filtration
system needs additional flushing.
The ice dispenser will not operate properly
Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
Ice bin installed correctly? Be sure the ice bin is firmly in
position.
New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
Ice clogged in the ice storage bin or delivery chute?
Remove clogged ice, using a plastic utensil if necessary.
Clean chute and bottom of storage bin using a warm moist
cloth, and dry both thoroughly. To avoid clogging and maintain
afresh supply of ice, empty the storage bin and clean both the
bin and delivery chute every two weeks.
Has the wrong ice been added to the bin? Use only cubes
produced by the current ice maker.
Has the ice melted around the auger (metal spiral) in the
ice bin? Empty the ice container. Use warm water to melt the
ice if necessary.
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If
cubed ice dispenses correctly, depress the button for
"crushed" ice and begin dispensing again.
Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.
11

The water dispenser will not operate properly
•Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."
Refrigerator connected to awater supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Is the water pressure at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."
Kink in the home water source line? Straighten the water
source line.
• New installation? Flush and fill the water system.
• Water filter installed on the refrigerator? The filter may be
clogged or incorrectly installed.
• Is a reverse osmosis water filtration system connected to
your cold water supply? See "Water Supply Requirements."
Water is leaking from the dispenser
NOTE: One or two drops of water after dispensing is normal.
• Glass not being held under the dispenser long enough?
Hold the glass under the dispenser for 2 to 3 seconds after
releasing the dispenser lever/pad.
New installation? Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."
Recently changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."
The dispenser water is not cool enough
(on some models)
NOTE: Water from the dispenser is chilled to only 50°F (10°C).
• New installation? Allow 24 hours after installation for the
water supply to cool completely.
Recently dispensed large amount of water? Allow 24 hours
for water supply to cool completely.
Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.
Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
ACCESSORIES
The following accessories are available for your refrigerator.
To order an accessory, call 1-800-442-9991 and ask for the part
number listed below or contact your authorized Jenn-Air dealer.
In Canada, call 1-800-807-6777.
affresh TMtStainless Steel Cleaner:
Order Part #W10355016
In Canada, order Part #W10355016B
affresh TMtStainless Steel Wipes:
Order Part #W10355049
In Canada, order Part #W10355049B
affresh TMtKitchen &Appliance Cleaner:
Order Part #W10355010
In Canada, order Part #W10355010B
Water Filter:
Order Part #W10295370 (P4RFWB)
Air Filter:
Order Part #W10311524
Produce Preserver:
Order Part #W10346771
WATERFILTER
CERTIFICATIONS
State of California
Department of Public Health
Water Treatment Device
CertificateNumber
10- 2030
Date Issoed: February 26, 2010
Trademark/Model Des _nation Replacement Elements
P5WB2L P4RFWB
L
ManutiJcturer: Whirlpool _orporadoI1
The water treatment deyiee_s) listed on this certificate have met the testi_lg r,,quiremet[ts p ursu a nt to Section
1168311 of the Iloa|th and Safety Code tier lhe tMlowing heal|h rel3ted contamihahts:
Microbiological Coniaminants and Turbidih,
Lysts
Or_anicContanlihant_
Atrazme
Lindane
Rated Service Capacity: 200 ga) Rated Service Flow: 5 gore
Conditions of Cer tit'ieation:
Do not use where walcr is micrl)biologlcaI[ b unsafe or with water of unknown _uahty, except that syslem_ certified
fi_r cyst reduction may be used on disinlbcted waters that may co_llain fihcrab]e cysls.
1-TM AFFRESH is a trademark of Whirlpool, U.S.A.
12

PERFORMANCEDATA SHEET
Water Filtration System
Model P5WB2L/P4RFWB Capacity 200 Gallons (757 Liters)
System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, and Particulate
Class I*; and against NSF/ANSI Standard 53 for the reduction of Live
Cysts, Asbestos, Lead, Lindane, Toxaphene, Atrazine, and 2,4 - D.
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Minimum %Average %
Aesthetic Effects Requirements Influent Concentration Effluent Reduction Reduction
Chlorine Taste/Odor 50% reduction 2.0 mg/L 2.0 mg/L + 10% 0.20 mg/L ** 97 97.2
Particulate Class I* 85% reduction 7,300,000 #/mL At least 10,000 particles/mL 75,000 #/mL 99 99.4
Contaminant NSF Reduction Average Influent Challenge Maximum Minimum %Average %
Reduction Requirements Influent Concentration Effluent Reduction Reduction
Live Cysts t 99.95% 160,000/L 50,000/L min. 54/U 99.97 99.99
Asbestos 99% 87 MFL 107to 108fibers/U t 0.17 MFL 99 99
Lead: @ pH 6.5 0.010 mg/L 0.160 mg/L 0.15 mg/L + 10% 0.001 mg/L 99.4 99.4
Lead: @ pH 8.5 0.010 mg/L 0.140 mg/L 0.15 mg/L _+10% 0.005 mg/L 98.6 98.6
Lindane 0.0002 mg/L 0.0019 mg/L 0.002 mg/L _+10% 0.00002 mg/L 98.9 99
Toxaphene 0.003 mg/L 0.014 mg/L 0.015 mg/L _+10% 0.001 mg/L 93 93
Atrazine 0.003 mg/L 0.0094 mg/L 0.009 mg/L _+10% 0.0005 mg/L 94.5 94.7
2,4 - D 0.07 mg/L 0.220 mg/L 0.210 mg/L _+10% 0.028 mg/L 87.5 96.1
Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).
• It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.
• Use replacement filter P4RFWB, part #W10295370.
2012 suggested retail price of $39.99 U.S.A./S49.99 Canada.
Prices are subject to change without notice.
Style 1 - When the water filter status display changes from
"GOOD" to "ORDER," order a new filter. When the filter indicator
reads "REPLACE," it is recommended that you replace the filter.
Style 2 - When the filter indicator changes from green to yellow,
order a new filter. When the indicator changes from yellow to red,
it is recommended that you replace the filter.
Style 3 - When the filter indicator reads 10%, order a new filter.
When the indicator reads 0%, it is recommended that you
replace the filter.
Style 4 - Press FILTER to check the status of your water filter. If
the filter indicator light is yellow, order a new filter. If the filter
indicator light is red, it is recommended that you replace the filter.
• After changing the water filter, flush the water system. See
"Water and Ice Dispensers" or "Water Dispenser."
• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory
conditions, actual performance may vary.
• The product is for cold water use only.
• The water system must be installed in compliance with state and
local laws and regulations.
• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
• Refer to the "Warranty" section for the Manufacturer's name,
address and telephone number.
• Refer to the "Warranty" section for the Manufacturer's limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33° - 100°F (0.6° - 37.8°C)
Service Flow Rate 0.5 gpm (1.9 Lpm) @60 psi
%
*Class I particle size: >0.5 to <1 um
**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
tBased on the use of Cryptosporidium parvum oocysts
ttFibers greater than 10 um in length
® NSF is a registered trademark of NSF International.
13

JENN-AII REFRIGERATORWARRANTY
FIRST YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is installed, operated and maintained according to instructions
attached to or furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will
pay for factory specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major
appliance was purchased.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM
In the second through fifth years from the date of purchase, when this major appliance is installed, operated and maintained according
to the instructions attached to or furnished with the product, Jenn-Air brand will pay for factory specified replacement parts and repair
labor for the following components to correct non-cosmetic defects in materials and workmanship in this part that prevent function of
the refrigerator and that existed when this major appliance was purchased:
• Refrigerator/freezer cavity liner if the part cracks due to defective materials or workmanship.
• Sealed Refrigeration system (includes compressor, evaporator, condenser, dryer and connecting tubing).
SIXTH THROUGH TENTH YEAR LIMITED WARRANTY (SEALED REFRIGERATION SYSTEM ONLY - LABOR NOT INCLUDED)
In the sixth through tenth year from the date of purchase, when this major appliance is installed, operated and maintained according to
instructions attached to or furnished with the product, Jenn-Air brand will pay for factory specified replacement parts for the following
components to correct defects in materials or workmanship in the sealed refrigeration system (includes compressor, evaporator,
condenser, dryer and connecting tubing) that existed when this major appliance was purchased.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THE LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Service must be provided by a designated Jenn-Air service company. This limited warranty is valid in the United States or Canada and
applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date
of the original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is
used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Jenn-Air.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.
6. Any food or medicine loss due to refrigerator or freezer product failures.
7. Pickup and delivery. This major appliance is intended to be repaired in your home.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Jenn-Air servicer is not available.
10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Jenn-Air's published installation instructions.
11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or
cannot be easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. Ifyou want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Jenn-Air or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies. 8/11
14

For additional product information, in the U.S.A., visit www.jennair.com
In Canada, visit www.jennair.ca
If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may
contact Jenn-Air at the number below.
Have your complete model number ready. You can find your model number and serial number on the label, located on the inside wall of
the refrigerator compartment.
For assistance or service in the U.S.A., call 1-800-536-6247. In Canada, call 1-800-807-6777.
If you need further assistance, you can write to Jenn-Air with any questions or concerns at the address below:
In the U.S.A.: In Canada:
Jenn-Air Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Jenn-Air Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please keep these User Instructions and the model number information for future reference.
15

NousvousREMERCIONSd'avoiracheteceproduitdehautequalite.Sivousrencontrezunproblemenonmentionne
danslasectionDI_PANNAGE,veuillezvisiternotresiteWebwww.jennair.compourdesinformationssupplementaires.Si
vousaveztoujoursbesoind'assistance,veuilleznoustel6phonerau1-800-536-6247.AuCanada,visiteznotresiteWeb
www.jennair.caoutel6phonez-nousau1-800-807-6777.
Vousaurezbesoindevosnum@osdemodeleetdes@iesituessurlaparoiinterneducompartimentderefrig@ation.
SECURITEDU REFRIGERATEUR
Votre securite et celle des autres est tres importante.
Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de
toujours lire tous les messages de s_curit_ et de vous y conformer.
Voici le symbole d'alerte de s_curit_.
Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves a vous
eta d'autres.
Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient •
nRisque possible de d_cbs ou de blessure grave si vous ne
suivez pas imm_diatement les instructions.
Risque possible de d_cbs ou de blessure grave si vous
ne suivez pas les instructions.
Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE SI_CURITI_
AVERTISSEMENT :Pour reduire les risques d'incendie, de choc electrique ou des blessures Iors de I'utilisation du
refrig6rateur, prendre quelques precautions fondamentales, y compris les suivantes :
• Brancher I'appareil sur une prise a 3 alveoles reliee a la terre. • Garder les materiaux et les vapeurs inflammables, telle
• Ne pas enlever la broche de liaison a laterre, que I'essence, loin du r6frigerateur.
• Ne pas utiliser un adaptateur. • Utiliser deux ou plus de personnes pour deplacer et
installer le refrig6rateur.
• Debrancher le refrig6rateur avant I'installation de la
• machine a glagons (seulement pour modeles pr_ts
• recevoir une machine a glagons).
• • Utiliser un verre robuste pour prendre des glagons (sur
• certains modeles).
• Ne pas heurter les portes en verre du r6frigerateur (sur
certains modeles).
CONSERVEZ CES INSTRUCTIONS
Ne pas utiliser un cable de rallonge.
Debrancher la source de courant electrique avant I'entretien.
Replacer pieces et panneaux avant de faire la remise en marche.
Enlever les portes de votre vieux r6frigerateur.
Utiliser un produit de nettoyage ininflammable.
16

Avertissements de la proposition 65 de I'¢:tat de Californie "
AVERTISSEMENT "Ce produit contient au moins un produit chimique connu par I'¢:tat de Californie pour 6tre & I'origine de
cancers.
AVERTISSEMENT "Ce produit contient au moins un produit chimique connu par I'¢:tat de Californie pour 6tre & I'origine de
malformations et autres d6ficiences de naissance.
Mise au rebut appropri( e
de votre vieux refrigerateur Avant de jeter votre vieux r_frig_rateur ou cong_lateur :
• Enlever les portes.
• Laisser les tablettes en place de sorte que les enfants ne
puissent pas y pen6trer facilement.
Risque de suffoquer
Enlever les portes de votre vieux r_frig_rateur.
Le non=respect de cette instruction peut causer
un d_c_s ou des I_sions c_r_brales.
IMPORTANT : L'emprisonnement et I'etouffement des enfants ne
sont pas un probleme du passe. Les refrigerateurs jetes ou
abandonnes sont encore dangereux, m_me s'ils sont laisses
abandonnes pendant "quelques jours seulement". Si vous vous
debarrassez de votre vieux refrigerateur, veuillez suivre les
instructions suivantes pour aider &eviter les accidents.
Renseignements importants apropos de la raise au
rebut des fluides r_frig_rants :
Mettre le r6frig@ateur au rebut conform6ment & la
r6glementation f_d@ale et locale. Les fluides refrigerants
doivent @re @acues par un technicien certifie et agree par
I'EPA conformement aux procedures @ablies.
UTILISATIONDU REFRIGERATEUR
Sur certains modeles, le sachet d'accessoires du refrigerateur
comprend un filtre a air qui doit _tre installe avant d'utiliser le Installation du filtre ,_air (sur terrains modules}
refrigerateur. Sur certains modeles, le filtre a air est preinstalle
I'usine. Le filtre doit _tre installe derriere la porte a aerations, situee (selon
le modele) le long de la paroi interieure gauche ou arriere,
proximite du sommet du compartiment de refrigeration.
Le filtre &air reduit I'accumulation d'odeurs. Ceci aide & maintenir
un environnement plus propre a I'interieur du refrigerateur. 1. Retirer le filtre a air de son emballage.
2. Ouvrir la porte avec aerations en la soulevant.
3. Emboiter le filtre pour le mettre en place.
17

Installation du t_moin de statut de filtre
(sur certains modules)
Le filtre comporte un temoin de statut qui doit etre active et
installe en meme temps que le filtre a air.
1. Placer le temoin oriente vers le bas sur une surface ferme et
plane.
2. Appliquer une pression sur la bulle situee a I'arriere du temoin
jusqu'a ce que la bulle eclate - ceci active le temoin.
3. Ouvrir la porte du filtre a air avec aerations en la soulevant.
Sur certains modeles, I'arriere de la porte comporte des
encoches.
4. ModUles avec encoches :
• Faire glisser le temoin vers le bas, dans les encoches, en
I'orientant vers I'exterieur.
REMARQUE : Le temoin ne glissera pas facilement dans
les encoches si la bulle arriere n'a pas eclat&
Fermer la porte du filtre &air et verifier que le temoin est
visible & travers le trou rectangulaire de la porte.
ModUles sans encoches :
Conserver le temoin dans un endroit visible dont
I'utilisateur se souviendra facilement - soit a I'interieur du
refrigerateur, soit dans un autre endroit de la cuisine ou du
domicile.
Remplacement du filtre _air
Le filtre & air jetable doit etre remplace tous les 6 mois, Iorsque le
temoin de statut est entierement passe du blanc au rouge.
Pour commander un filtre & air de rechange, voir "Accessoires".
1. Retirer I'ancien filtre &air en serrant les onglets lateraux.
2. Retirer I'ancien temoin de statut.
3. Installer le filtre & air et le temoin de statut neufs a I'aide des
instructions des sections precedentes.
Sur certains modeles, le sachet d'accessoires du refrigerateur
comprend un sachet de conservation pour produits frais, qui doit
etre installe avant d'utiliser le refrigerateur. Sur certains modeles,
le sachet de conservation pour produits frais est preinstalle
I'usine.
Le sachet de conservation pour produits frais absorbe I'ethylene,
permettant ainsi un ralentissement du processus de maturation
de nombreux produits frais. Ainsi, la fraicheur de certains produits
frais est prolongee.
La production d'ethylene et la sensibilite des produits a I'ethylene
varie selon le type de fruit ou de legume. Afin de preserver la
fraicheur, il est preferable de separer les produits frais sensibles
I'ethylene des fruits produisant des quantites d'ethylene
moderees a elevees.
Pommes
Asperges
Baies
Brocoli
Melon brode
Carottes
Agrumes
Raisin
Laitue
Poires
I_pinards
Sensibilit_
I'_thylbne
12levee
Moy.
Basse
12levee
Moy.
Basse
Moy.
Basse
12levee
12levee
12levee
Production
d'_thylbne
Tr_s elevee
Tr_s basse
Basse
Tr_s basse
€:levee
Tr_s basse
Tr_s basse
Tr_s basse
Tr_s basse
Tr_s elevee
Tr_s basse
Installation du sachet de conservation
pour produits frais (sur certains modules)
ATTENTION :IRRITANT
PEUT IRRITER LES YEUX ET LA PEAU. DI_GAGE DES
12MANATIONS DANGEREUSES LORSQUE MI2LANGI 2
AVEC D'AUTRES PRODUITS.
Ne pas m_langer avec d'autres agents de nettoyage tels
que I'ammoniaque, un agent de blanchiment ou des
acides. Eviter tout contact avec les yeux, la peau ou les
v_tements. Ne pas respirer les poussi_res. Tenir hors de la
port_e des enfants.
PREMIERS SOINS : Contient du permanganate de
potassium. En cas d'ingestion, appeler imm_diatement un
centre antipoison ou un m_decin. Ne pas provoquer le
vomissement. En cas de contact avec les yeux, rincer avec
de I'eau pendant 15 minutes. En cas de contact avec la
peau, bien rincer avec de I'eau.
Les sachets de conservation pour produits frais doivent etre
installes dans leur Iogement, situe le long d'une paroi laterale
interne du bac & legumes ou du tiroir convertible.
REMARQUE : Pour une performance ideale, toujours utiliser les
deux sachets.
18

1. Retirer les sachets de conservation pour produits frais de leur
emballage.
FreshFlow
produce preserver
CAUTION ATTENTION
IRRITANT IRRITANT
Read cautions on back, Life les mises en garde au dos,
2. Soulever le Iogement pour I'extraire de la languette de
montage le long de la paroi.
3. Ouvrir le Iogement en soulevant I'arriere du sommet du
Iogement pour I'extraire.
4. Placer les deux sachets & I'interieur du Iogement puis
emboiter les deux parties du Iogement pour le refermer.
5. Reinstaller le Iogement sur la languette de montage le long de
la paroi.
Installation du t_moin lumineux (sur certains modules)
Le sachet de conservation pour produits frais comporte un temoin
lumineux qui doit _tre active et installe en m_me temps que le
sachet.
1. Orienter le temoin vers le bas en le plagant sur une surface
ferme et plane.
2. Appliquer une pression sur la bulle situee & I'arriere du temoin
jusqu'& ce que la bulle eclate - ceci active le temoin.
3. Ouvrir le couvercle du Iogement du sachet de conservation
pour produits frais.
4. Placer le temoin sur le sommet du Iogement en I'orientant vers
I'interieur.
5. Fermer le couvercle en le faisant coulisser et verifier que le
temoin est visible & travers le trou rectangulaire du couvercle.
REMARQUE : Le couvercle ne se fermera pas facilement si la
bulle arriere du temoin lumineux n'a pas eclat&
Remplacement du sachet de conservation
pour produits frais (sur certains modules)
Les sachets jetables doivent _tre remplaces tousles 6 mois,
Iorsque le temoin est entierement passe du blanc au rouge.
Pour commander des sachets de rechange, voir "Accessoires".
1. Retirer les anciens sachets du Iogement du conservateur pour
produits frais.
2. Retirer I'ancien temoin.
3. Installer les sachets et letemoin neufs en suivant les
instructions des sections precedentes.
i,J s<xon des commc nd®s
Les commandes du refrigerateur et du congelateur se trouvent sur
le tableau de distribution.
IMPORTANT :Uecran d'affichage sur le tableau de commande
du distributeur s'eteint automatiquement et entre au mode "veille"
Iorsque les boutons de commande et les plaques de distribution
n'ont pas ete utilises pendant au moins 2 minutes. Le fait
d'appuyer une fois sur un bouton de commande au mode "veille"
reactive uniquement I'ecran d'affichage, sans modifier les
reglages. Apres reactivation, n'importe quel reglage peut alors
_tre modifi& Si aucune modification n'est apportee dans les
2 minutes qui suivent, I'affichage passe de nouveau au mode
"veille".
• Appuyer sur n'importe quel bouton de commande sur le
tableau de distribution pour activer I'ecran d'affichage.
L'ecran d'accueil apparait tel qu'indiqu&
Ajustement des commandes
Pour votre confort, les commandes du refrigerateur et du
congelateur sont prer6gl6es a I'usine. Lors de I'installation initiale
du refrigerateur, s'assurer que les commandes sont encore
prereglees au "reglage moyen". Les points de reglage
recommandes par I'usine sont 37°F (3°C) pour le refrigerateur et
0°F (-18°C) pour le congelateur.
IMPORTANT :
Attendre 24 heures avant d'ajouter des aliments dans le
refrigerateur. Si on ajoute des aliments alors que le
refrigerateur n'a pas completement refroidi, les aliments
risquent de s'abimer.
REMARQUE :Ajuster la commande sur un reglage plus froid
que celui qui est recommande ne refroidira pas les
compartiments plus rapidement.
Si latemperature est trop tiede ou trop froide dans le
refrigerateur ou le congelateur, verifier d'abord les events pour
s'assurer qu'ils ne sont pas bloques, avant de regler les
commandes.
Les reglages preregles devraient _tre corrects pour I'utilisation
domestique normale. Les reglages sont faits correctement
Iorsque le lait ou le jus sont aussi froids que vous I'aimez et
Iorsque la creme glacee est ferme.
Attendre au moins 24 heures entre les ajustements. Verifier de
nouveau les temperatures avant de proceder a d'autres
ajustements.
19

Pour visualiser et ajuster les points de reglage, appuyer pendant
3 secondes sur la touche TEMP (temperature). Lorsque le mode
de reglage est active, les donnees d'ajustement apparaissent sur
I'ecran d'affichage.
REMARQUE • Pour visualiser les temperatures en Celsius,
appuyer sur la touche OPTIONS Iorsque le mode de reglage est
activ& Pour revenir au mode d'affichage en Fahrenheit, appuyer
de nouveau sur OPTIONS.
• Lorsque le mode de reglage est active, I'ecran d'affichage
indique le point de reglage du refrig6rateur et "FRIDGE"
(refrig6rateur) apparait.
Appuyer sur les fleches du bouton SELECT (selection) pour
augmenter ou diminuer le point de reglage.
Apres avoir fini de visualiser (et d'ajuster, si desire) le point de
reglage du refrigerateur, appuyer sur TEMP (temperature) pour
modifier I'affichage et faire apparaitre le point de reglage du
congelateur. Une fois le changement de zone effectue,
"FREEZER" (congelateur) apparait sur I'ecran d'affichage.
Appuyer sur les fleches du bouton SELECT (selection) pour
augmenter ou diminuer le point de reglage.
Apres avoir fini de visualiser (et d'ajuster, si desire) les points
de reglage du refrigerateur et du congelateur, appuyer sur
LIGHT (eclairage) pour sauvegarder les reglages.
REMARQUE •Pour sortir sans sauvegarder les modifications,
laisser 60 secondes d'inactivite s'ecouler; le mode de reglage
s'eteindra automatiquement.
Pour ajuster les points de reglage de temperature, utiliser le
tableau suivant comme guide.
CONDITION : AJUSTEMENT DE LA
TEMPleRATURE :
RC:FRIGC:RATEURtrop froid Reglage du RC:FRIGC:RATEUR
1° plus haut
RC:FRIGC:RATEURtrop tiede Reglage du RC:FRIGC:RATEUR
1° plus bas
CONGC:LATEUR trop froid Reglage du CONGC:LATEUR
1° plus haut
CONGC:LATEUR trop tiede /Reglage du CONGC:LATEUR
Trop peu de gla£;ons 1° plus bas
La gamme de valeurs de reglage pour le refrigerateur va de 33°F &
45°F (0°C &7°C). La gamme de valeurs de reglage pour le
congelateur va de -5°F &5°F (-21°C &-15°C).
Refroidissement On/Off (marche/arr_t)
Nile refrigerateur, nile congelateur ne refroidiront Iorsque le
refroidissement est desactiv&
• Pour desactiver le refroidissement, appuyer simultanement
sur les boutons OPTIONS et FILTER (filtre) pendant
3 secondes.
IMPORTANT : Afin d'eviter de verrouiller le distributeur ou de
modifier des reglages involontairement, veiller &appuyer sur
les deux boutons exactement au meme moment.
Lorsque le refroidissement est desactive, "COOLING OFF"
(refroidissement desactive) apparait sur I'ecran d'affichage.
Appuyer de nouveau pendant 3 secondes sur OPTIONS et
FILTER (filtre) pour reactiver le refroidissement.
Caract_ristiques suppl6mentaires
Speed Ice (gla£ons acc_16r_s) et
Max Cold (refroidissement maximal)
La caracteristique Speed Ice (gla£_onsacceleres) est utile Iors
d'une utilisation intense de gla(_ons en augmentant la production
de gla(_ons sur une periode de 24 heures.
La caracteristique Max Cold (refroidissement maximal) est utile
Iors de periodes d'utilisation intensive de gla(_ons, d'ajout d'un
grand nombre d'aliments ou de I'elevation temporaire de la
temperature de la piece.
• Pour activer la caracteristique Speed Ice (gla£_onsacceleres),
appuyer sur OPTIONS. "Speed Ice" (gla£;ons acceleres)
apparait sur I'affichage.
La caracteristique Speed Ice (gla(_ons acceleres) reste activee
pendant 24 heures & moins d'etre desactivee manuellement.
Pour activer la caracteristique Max Cold (refroidissement
maximal), appuyer une deuxieme fois sur OPTIONS. La
caracteristique Speed Ice (gla(_ons acceleres) s'eteint et la
caracteristique Max Cold (refroidissement maximal) est
activee. "Max Cold" (refroidissement maximal) apparait sur
I'affichage.
La caracteristique Max Cold (refroidissement maximal) reste
activee pendant 24 heures a moins d'etre desactivee
manuellement.
Pour activer simultanement les caracteristiques Speed Ice et
Max Cold, appuyer une troisieme fois sur OPTIONS. "Speed
Ice" (gla£_onsacceleres) et "Max Cold" (refroidissement
maximal) apparaissent sur I'affichage.
Les deux caracteristiques restent activees pendant 24 heures
&moins d'etre desactivees manuellement.
Pour desactiver les deux caracteristiques, appuyer une
quatrieme fois sur OPTIONS. "Speed Ice" (gla(_ons acceleres)
et "Max Cold" (refroidissement maximal) disparaissent de
I'affichage.
Lorsque Speed Ice et/ou Max Cold sont actifs, les affichages de
temperature restent les memes. Au bout de 24 heures, le
refrigerateur revient aux points de reglage de la temperature
precedents.
REMARQUE : Si on desire une production accrue de gla£_ons en
permanence, regler la commande du congelateur & une
temperature inferieure. Le reglage du congelateur & une
temperature plus froide peut rendre certains aliments, comme la
creme glacee, plus durs.
Alarme de porte entrouverte
La caracteristique d'alarme de porte entrouverte fait entendre un
signal d'alarme Iorsque la porte du refrigerateur ou du congelateur
est ouverte pendant 5 minutes et que le systeme de
refroidissement fonctionne. L'alarme retentira toutes les
2 minutes. Fermer les deux portes pour I'arreter. La
caracteristique se reinitialise ensuite et se reactive si I'une des
deux portes est de nouveau laissee ouverte pendant 5 minutes.
20