Jescraft SSB-4845 User manual

OPERATIONAL SAFETY AND ASSEMBLY INSTRUCTIONS
985-0012 Rev 0
SINGLE SIDED SLAB BUGGY
Models: SSB-4845
READ THESE INSRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. KEEP THIS MANUAL HANDY FOR FUTURE REFERENCE.
OPERATION AND SAFETY
•Do not use this equipment if you are in poor health, taking medicaons,
drugs, or have been consuming alcohol, all of which may impair your
ability to work safely on this product.
•Always use this product in compliance with local or naonal laws,
regulaons, codes, and any other standards enforced in the locaon
where the product is used. This is the responsibility of the owner/user.
•Inspect product before each use. Do not use if damaged or if any
unusual noise or movement is observed. Check for missing parts.
•Examine thoroughly to make sure buggy is set up properly. If assembling
or ghtening fasteners, ghten all fasteners to the torque
specied: Recommended Tightening Torque: 21 -lbs. Do not exceed
27 -lbs. Do not overghten – overghtening can cause damage to the
unit. Do not replace or substute bolts, nuts, or other hardware that is
of lesser quality than the hardware supplied by the manufacturer.
•All components must be complete, funconing properly and correctly
assembled. If a malfuncon occurs, remove the product from service
and nofy your supervisor and maintenance personnel about the issue.
•Any incomplete part, missing part, or ill-ng part should be replaced
prior to use.
•Keep the product clean & dry. Lubricate moving parts. Proper use,
maintenance, and storage are essenal for this product to funcon
properly.
•Use the right product for the job. Do not modify the buggy and do
not use the buggy for a purpose for which it was not intended.
•Do not exceed the maximum load capacity of 1,450 lbs.
•Always distribute objects on the buggy evenly and resng adequately on
the upright supports. Uneven weight distribuon and/or top-heavy
loading could cause buggy pping.
•Be aware of dynamic loading. Suddenly dropping or bouncing a load on
the buggy may create, for a brief instant, an excess load, which may
result in damage to the product and/or personal injury.
•This buggy must be used on solid at surfaces.
•This Buggy must be used on a rm surface that is free of pits, debris,
holes or obstrucons.
•Acids are corrosive and can seriously aect strength. Do not expose this
buggy to corrosive substances.
•Never move a buggy with a worker within.
•Do not use powered devices to propel this buggy. Use extra cauon
near operang machinery.
•Do not modify or add to this buggy or any of its components in any way.
•Do not remove any labels from this buggy.
•Always use this product in accordance with the instructions in this manual
and consistent with any training relevant to machines, devices, materials,
etc. used in conjunction with this product.
Picture may differ from
actual product
ADAPTABLE PIPE & CONDUIT CART
Models: ATC-5834PL-2R2S; *Base ATC cart with optional Jescraft Casters
READ THESE INSRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT. KEEP THIS MANUAL HANDY FOR FUTURE REFERENCE.
READ BEFORE BEGINNING ASSEMBLY AND USE
FAILURE TO READ, UNDERSTAND AND FOLLOW ALL SAFETY RULES AND ASSEMBLY INSTRUCTIONS IN THIS
MANUAL BEFORE ASSEMBLING, INSTALLING, USING OR SERVICING OF THE PRODUCT IS A MISUSE OF THE
PRODUCT AND COULD RESULT IN SERIOUS INJURY OR DEATH. IF AFTER READING THE MANUAL YOU DO
NOT UNDERSTAND AN INSTRUCTION, ASK YOUR SUPERVISOR OR EMPLOYER FOR CLARIFICATION.
JESCRAFT IS NOT LIABLE FOR ANY INJURY OR PROPERTY DAMAGE THAT OCCURS AS A CONSEQUENCE OF
FAILING TO APPLY EITHER: a) THE INSTRUCTIONS IN THIS MANUAL; OR b) INFORMATION PROVIDED ON
LABELS AFFIXED TO THIS PRODUCT. NEITHER IS JESCRAFT RESPONSIBLE FOR ANY CONSEQUENTIAL
DAMAGES OR INJURYS SUSTAINED AS A RESULT OF FAILING TO EXERCISE SOUND JUDGMENT WHILE
ASSEMBLING, INSTALLING, USING OR MAINTAINING THIS PRODUCT.
METAL CONDUCTS ELECTRICITY:
Do not use this equipment where contact may be made with power lines or other live electrical circuits.
DO NOT OVERLOAD:
This buggy is designed to support a maximum load of 1,450 lbs. DO NOT exceed this maximum rated load. Do not load
materials higher than the upright components.

OPERATIONAL SAFETY AND ASSEMBLY INSTRUCTIONS
985-0012 Rev 0
ALWAYS
INSPECT
BEFORE
USE
CART MAXIMUM LOAD
CAPACITY: 1,450 lbs.
METAL CONDUCTS
ELECTRICITY
ACIDS ARE CORROSIVE.
DO NOT EXPOSE UNIT
TO CORROSIVE
SUBSTANCES
UNEVEN WEIGHT
DISTRIBUTION COULD
CAUSE CART TIPPING
MUST BE USED ON A FIRM
SURFACE THAT IS FREE OF
PITS, DEBRIS, HOLES OR
OBSTRUCTIONS
UNIT SHALL ONLY BE
USED ON FIRM AND
LEVEL SURFACES
NEVER MOVE A CART
WITH WORKER WITHIN
SUDDENLY DROPPING OR
BOUNCING A LOAD ON THE
CART MAY CREATE AN
EXCESS LOAD
All photos, drawings and depictions in this booklet are for reference purposes only and may differ from actual product. Refer to
applicable OSHA, ANSI or CSA codes and regulations for the proper use of this equipment.