Home Styles 4511-95 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver
4511-95
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Kitchen Cart
Adjustable Pin
8 pcs. (+1 extra)
M4x25
Machine Screw
5 pcs.
Knob
5 pcs.
M3x16
Wood Screw
for Leaf Support
6 pcs. (+1 extra)
M3x16
Wood Screw
for Magnet
4 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
24 pcs. (+1 extra)
M3.5x25
Flat Head Screw
3 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
24 pcs. (+1 extra)
Hex Wrench
1 pc.
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
M6x25
Head Cap Bolt
4 pcs. (+1 extra)
M6x38
Head Cap Bolt (long)
4 pcs. (+1 extra)
Magnet
2 pcs.
A.
Top
1 pc.
C.
Side Panel
1 pc.
E.
Back Panel
3 pcs.
D.
Middle Panel
1 pc.
H.
Back Rail
1 pc.
F.
Back Upright
2 pcs.
M.
Rack Side
1 pc.
N.
Rack Side
1 pc.
P.
Rack
1 pc.
O.
Rack Base
1 pc.
J.
Base
1 pc.
K.
Arm
2 pcs.
L.
Towel Bar
1 pc.
S.
Shelf
2 pcs.
Q.
Door
1 pc.
R.
Door
1 pc.
U.
Leaf
Support
1 pc.
T.
Drawer
3 pcs.
V.
Leaf
Support
1 pc.
I.
Front Rail
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
B.
Side Panel
1 pc.
G.
Back Rail
1 pc.
W.
Front Rail
1 pc.
Caster
2 Locking
2 Non-Locking
4 pcs.
Small
Hex Wrench
1 pc.

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Assemble Rack Sides (M), (N), Rack Base (O) and Rack (P).
M
N
OP
STEP 2
Attach unit to Side Panel (C) with Head Cap Bolts.
C
Head Cap Bolt
B
K
K
STEP 3
Attach Arms (K) to Side Panel (B) with Head Cap Bolts.
Head Cap Bolt

Assembly Instructions 3/7
CE
F
G
H
EE
FB
Lock
Figure 1 Figure 2
STEP 4
Attach Back Rail (G)
to Side Panel (C),
then flip Locks.
(See Figures 1 and 2)
Attach Back Uprights (F)
to unit.
Slide Back Panels (E)
into position.
Attach Back Rail (H) to unit,
then flip Lock.
Attach Side Panel (B) to unit,
then flip Locks.
Figure 3
STEP 5
Attach Base (J) to unit with
Head Cap Bolts (long),
then flip Locks.
(See Figure 3)
Note: Arrow label
indicates front of Base (J).
J
Head Cap Bolt (long)
Lock
Arrow label at front

Assembly Instructions 4/7
Figure 4
STEP 6
Attach Casters to unit with Head Cap Bolts
for Caster into pre-drilled holes
with Locking Casters at front.
(See Figure 4)
Note: Arrow label indicates front of unit.
Arrow label at front
Head Cap Bolt for Caster
Non-Locking Caster
Locking Caster
Wood Screw for Magnet
Magnet
STEP 7
Attach Magnets to Front Rail (W)
by inserting Wood Screws for Magnet
into pre-drilled holes, then tighten.
(See Figure 5)
Figure 5
W

Assembly Instructions 5/7
Figure 6
STEP 9
Attach Leaf Supports (U) and (V) to unit
with Wood Screws for Leaf Support.
(See Figure 6)
Wood Screw for Leaf Support
V
U
STEP 8
Turn unit over to its
upright position.
Attach Middle Panel (D)
and Front Rails (I), (W) to unit,
then flip Locks.
Insert Wood Screws (short)
into pre-drilled holes in unit,
then tighten.
Slide Towel Bar (L) into position.
I
I
D
Lock
Wood Screw (short)
L
W

Part List
T2.
Drawer Back
3 pcs.
T5.
Drawer Bottom
3 pcs.
T1.
Drawer Front
3 pcs.
T3.
Drawer Side
3 pcs.
T4.
Drawer Side
3 pcs.
T5
STEP 12
Attach Knob with Machine Screw.
Drawer (T)
Wood Screw (short)
Roller at back
T1
T2
T3
T4
Bottom
STEP 10
Attach Drawer Front (T1) and Drawer
Back (T2) to Drawer Side (T3)
with Wood Screws (long).
Attach Drawer Side (T4) to unit
with Wood Screws (long).
Wood Screw (long)
Machine Screw
Knob
STEP 11
Slide Drawer Bottom (T5) into groove.
Attach Drawer Bottom (T5) to
unit with Wood Screws (short).
Assembly Instructions 6/7

T
T
T
Assembly Instructions 7/7
Machine Screw Knob
Adjustable Pin
Q
R
S
S
STEP 13
Insert Adjustable Pins into side panel and middle panel at desired level.
(See Figure 7)
Place Shelves (S) into position.
Attach Doors (Q) and (R) by sliding door hinges into side panel hinges.
(See Figure 8)
Attach Knobs to Doors (Q) and (R) with Machine Screws.
(See Figure 9)
Figure 7
Figure 8
Figure 9
Lock
Flat Head Screw
A
STEP 14
Attach Top (A) to unit
with Flat Head Screws, then flip Locks.
Slide Drawers (T) into position.
T
T
T

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customerservice/replacement-parts
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319