JetBlack JBT-S1-V2 User manual

1) WARNING
• Readandfollowallinstructionsconcerningtrainersetupandinstallationofyour
bicycleintothetrainer.Failuretosecurelyattachthebicycletothetrainercouldresult
inseriousinjurytotheriderorbystanders.
• Removealloilsandmoisturefromtherollerandthetyrebeforeuse.
• Keepbothhandsonhandlebaratalltimes.
• Donotover-tightentheadjustmentknobs.Overtighteningmaycausedamagetothe
traineroryourbicycleframe.Theclamphandlesshouldbermandsecure.DoNOT
force!
• Regularlycheckyourtrainer,particularlythemountingsystem,fordamage.Ifyouthink
yourtrainermaybedamaged,donotuseitandcontactyoursupplier.
• Alwaystakecarewhentrainingtopreventchildrenorpetsmovingclosetothetrainer.
2) CAUTION
• Thistrainerisintendedforsingle-riderbicyclesonly.
• Readandfollowallinstructions.
• Beforebeginningeachworkout,besurethebicycleissecurelyattachedtothetrainer.
• Ensureyoualwaysusethetraineronaatsurface.
• Donotputngers,feetordanglingobjectsnearanymovingparts.
• Donotattempttodismountuntilallmovingpartshavecometoastandstill.
• DonotattempttomodifyyourJetBlacktrainer.
• Donotattempttostoptheresistanceunitorywheelmanually.
• Resistanceunitcanbecomehotenoughtocauseburns.Donottouchresistanceunit
duringuseandforsomeperiodafteruse,untilithashadsufcienttimetocool.
• Keepchildrenandpetsawayfromthetrainerduringuse.
• Beforeyoustartanyexerciseprogramyoushouldconsultaphysician.Shouldyou
becomeill,feeldizzy,light-headedornauseouswhileridingthetrainer,stopriding
immediatelyandseekmedicalattention.
• Therolleradjustmentknobmustbetightenedcorrectlytopreventdamagetothe
trainer.
www.jetblackcycling.com
[email protected]
JBT-S1-V2
with Lite APP

3) BICYCLE MOUNTING
INITIAL SETUP
This setup must be followed every time a bicycle with a different axle length is used.
BICYCLE SETUP
1. Yourbicyclemustbeingoodmechanicalcondition,ifyouareunsurepleaseseeyour
localbicycleservicecentreforassessment.
2. Yourbicyclewheelmustbeingoodcondition,trueandfreefromanyissues.The
wheel’srimmusthavelessthan2mmsidetosidemovementandlessthan1mm
verticalmovementperrevolution.Ifyourwheelisoutsideofthis,pleasevisityourlocal
bicycleservicecentretohaveittrued.Untruewheelsmaycausevibrationduringuse
andcouldcausepermanentdamagetothetrainerortrainerroller.
3. Tomeasuretnessimprovementitisimportanttouseconsistenttyrepressuresfor
eachworkout.
For road bike tyres we recommend 110psi.
For mountain bike tyres please see that manufacturer’s guidelines written
on the tyre sidewall.
ThetrainerbasepowercurvesusedintheJetBlackapparemeasuredonabikeusing
700x23cslickroadtyresat110psiwithexactly1.5completeturns(threehalfturns)
oftherolleradjustmentknobaftertherollerrstmakescontactwiththetyre.Lower
pressurescanstillbemeasuredaslongastheyareusedconsistently.
Standard Nut and Bolt
• Ensurethenutsonyouraxlearetightenedsecurely
• Checkthatthenutandaxlenestsintotheaxlesupportcupsbymorethan5mm(3/16
inch)
Quick Release Skewer
• JetBlackstronglysuggestsyouusethesuppliedquickreleaseskewer(forthose
bicyclesthatuseQRsystems
• Replacethebicycle’srearwheelquickrelease(QR)skewerwiththeoneprovided.See
yourbicycleowner’smanualforinstructionsonhowtoproperlyadjusttheQRskewer.
• Theskewerlevermustbeonthenon-drivesideofyourbicycle(thelefthandside).
• Yourskewermustbetightandyourwheelmustbealignedproperlyinthebicycle.
Thru Axle
• Bicyclesthatuseathruaxlesysteminmostcasesdonotnesttheminimumof5mm
(3/16inch)intotheaxlesupportcups.Ifyourthruaxledoesnotnestmorethan5mm
(3/16inch),youshouldacquireatrainerspecictrainerthruaxlethatissuitablefor
yourbicycle.Thesearesoldseparately.
• Installyourtrainerspecicthruaxlemakingsuretofollowthemanufacturer’s
instructions.
BICYCLE SETUP
1. Checkyourtyrepressureisinatedtowhichevercomesrst;thetyremanufacturer’s
maximumrecommendedpressureor110psiifyourtyreswillallow.
2. Onthelefthandside,adjustthesilverthreadedboltandblackplasticlocknutsothat
theyareallthewayin,withnothreadshowing.Thiswillgiveyouplentyofroomasyou
movethebikeintoposition.
3. Takeyourbikeandgentlyloweryourbikeintothetrainerframe.Alignthebikeandrear
wheeltotheleftsideofthetrainersothatthebicycleaxleisrmlyrestinginsidethe
threadedadjustmentbolt.
4. Note:Iftherolleristouchingthetyreandnotlettingtheaxlenestintotheaxlesupport
cupyoumayneedtolowertheresistanceunitbywindingtherolleradjustmentknob
anticlockwise.SeeDiagram2.
5. Carefullyliftyourbikeintoposition,aligningtherearQRskewerwiththeaxleclamp
cones.Whileholdingthebicyclesteady,slidetherightsideQRskewernutintothe
axleclampcone.Usingtheadjustmentknobandthereleaseclamp,tightentheclamp
conesuntiltheycomeintocontactwiththebicycle’sQRskewerends.Makesurethat
theQRskeweralignswiththenotchintheclampcones.Rotatetheclampconecupto
centrethebicycle’srearwheeloverthecentreoftherollerontheresistanceunit.See
diagram1.
6. Aftercontactismade,tightenthedriveside(righthand)adjustmentknobuntilthebike
issecurelyheld–anadditionalfewcompleteturnsofthehandle.
7. Whenyouhavecompletedthesestepsmakesuretheblacklockingringisrotated
clockwiseuntilitisrmlyagainstthetrainerframe.Thiswilllockthethreadedboltin
place,preventingitfromtighteningorlooseningduringuse.
8. Checkthebicycleissecureinthetrainerframe.Thebicyclemustnotmoveseparately
fromthetrainer.Testthisbyholdingthebicyclesaddleandmovingitfromsidetoside
andupanddown.Ifthebicyclemovespleasereturntoinitialsetup.SeeDiagram3.
9. Finallycheckthattherolleristightenedtoexactly1.5turns(threehalfturns)afterthe
tyrerstmakescontactwiththeroller.SeeDiagram5.
IMPORTANT:
Ensurethatyourtyreiscentredontherollertowithin10mm(3/8inch)fromthecentre
oftheroller.Yourtyremusthaveaminimum5mm(3/16inch)clearancefromthemetal
(silvercoloured)rollerframe.SeeDiagram4

4) USING YOUR TRAINER
GETTING THE BEST FROM YOUR TRAINER:
Do not ride your trainer with less than 1.5 complete turns (three half turns) of the roller
adjustment knob after the roller rst makes contact with the tyre.Itisimportantthatthe
tensionbetweenthetyreandtherollerissetcorrectlyeverysessionfortworeasons.(1)
Itensuresthatthetyrewillnotslipontherollerwhichcouldcausepermanentdamage
tothetrainerandyourtyre.(2)Itensurestheresistanceofyourtrainerisconsistentfor
everytrainingsessionallowingyoutotrackperformance.
ThetrainerbasepowercurvesusedintheJetBlackapparemeasuredonabikeusing
700x23cslickroadtyresat110psiwithexactly1.5completeturns(threehalfturns)ofthe
rolleradjustmentknobaftertherollerrstmakescontactwiththetyre.Ifyoursetupis
differentyouwillhaveaslightlydifferentresistance,butaslongasyoukeepthesetup
identicalbetweeneachtrainingsessionsyouwillbeabletomonitoryourperformance.
Tomakeyourindoorworkoutasquietaspossible,setthetraineronaJetBlackTrainer
Matanduseareartyrewithasmoothtreadpattern.Onceattached,thebicycleslopes
downwardslightly.Tolevel,usetheoptionalJetBlackRiserBlockunderthefronttyre.
CONSISTENT REPEATABLE TRAINING SESSIONS:
1. Increasingthetensionoftherollerfromourrecommended1.5turnsto2fullturns
willincreasetheresistanceapproximately10-15%.Soifyouareusingthetrainerfor
trackingyourpowerperformance,youshouldresistadjustingtherollerupto2full
turns.
2. Forevery20psiyourtyredeatesyouwillloseapproximately5%resistance.Youmust
checkyourtyrepressurebeforeeveryridemakingsureitisinatedtowhichever
comesrstthetyremanufacturer’smaximumrecommendedpressureor110psiifyour
tyreswillallow.
TRAINER SPARE PARTS
Sport
MagTRAINER
ITEM CODE DESCRIPTION
JBT-35 JB Frame bushing (S1 Sport)
JBT-15B JB Axle support cup Drive Side
JBT-15C JB Axle support cup Non-Drive-Side
JBT-32 JB Axle bolt With Axle Support Cup - Drive-Side (S1 Sport)
JBT-32B JB Axle bolt With Axle Support CUP - Non-Drive-Side (S1 Sport)
JBT-37 JB Foot For Trainer Base (S1 Sport)
JBT-22 JB Skewer For Trainer (not Pictured)
JBT-30 JB Resistance unit assembly (S1 Sport)
JBT-36 JB Resistance Unit Adjustment Bolt With Knob (S1 Sport)
S1 - TRAINER PARTS
JBT-36
JBT-30
JBT-37
JBT-15C
JBT- 13
JBT-32B
JBT-15B
JBT-32
www.jetblackcycling.com
[email protected]
5) BIKE REMOVAL
Undotherolleradjustmentknobonbyturningitanticlockwise1.5turnstobacktheroller
awayfromthetyre.Holdyourbikewithonehandandwiththeotherhandundothedrive
sideadjustmentknob,turningittowardsyourbicycleframe.Nowunscrewtheouter
adjustmentknobuntiltheaxlesupportcupsareunscrewedawayfromthebicycle.Now
youmaycarefullyremovethebikeforwardsorupwards,untilitclearsthetrainerframe.
6) CARING FOR YOUR TRAINER
Whenusedaccordingtothemanufacturer’sinstructionsandcaredforwithcommon
sense,yourJetBlacktrainerwillprovidealifetimeoftraining.
Wipeanysweatoffafteraworkout.
Keepthemachineawayfromanycorrosivesubstances,suchassaltorotherpotentially
hazardoussubstances.
Iftherollerdarkensorshowsblacktyrebuildupyoumaycleanitoffwithacloth.This
tyrebuildupcanbecleanedwitharagbyfrictionrubbingtherollerwithasidetoside
motion.Therubbingmotionwithacleanragwillliftthetyrebuildupofftheroller.Donot
usealcoholoranycleaningsolventsonthehydrogelroller.Acleanclothandfrictionisall
thatisrequired.
7) STORAGE
Caution!Thetrainerwillbecomehotduringuse.Keepchildrenandpetsawayandallow
trainer15minutestocooldownbeforetransportingorstoringyourtrainer.
Tostoreortransportyourtrainer:
Graspthetrainerframebytheadjustmentbolts/axlesupportcupsandthenliftsothatyou
mayfoldthelegstogether.
Becarefulwhenfoldingthelegstoavoidpinchingyourngers.
Storethetrainerindoors,outoftherainandawayfromtemperatureextremes.
Keepthetrainerawayfromanycorrosivesubstances,suchassaltorotherpotentially
hazardoussubstances.
8) WARRANTY
JetBlackofferstheoriginalowneralifetimewarrantyagainstmanufacturingdefects
manufacturingdefectsinmaterialsandworkmanship.Unitswhichusebatteriesor
computerdisplayunitcomewithaoneyearwarrantyontheseproducts.Thiswarranty
isnotapplicabletodamagecausedbymisuse,abuse,neglect,accidentorunauthorized
modication.Iftheunitisdisassembledbytheconsumer,thiswarrantyisvoid.
Itistheresponsibilityofthepurchasertoretainreceiptsforproofofpurchaseintheevent
thatwarrantyisrequired.ReturninggoodstoJetBlackortheplaceofpurchaseisdoneat
theowner’sexpense.
Ifyouexperienceproblemswithyourtrainer,pleaseemailusat
[email protected]
FREE JETBLACK TRAINING APP
New and exclusive to JetBlack!
FreeliteappforiOSorAndroidwithMultiplecoachingsessionscraftedbyOlympiccycle
coachMurrayHealey.
• UploadyourworkouttoTrainingPeaksandStrava!
• TestandmonitoryourselfwithaninbuiltFitness/ZonetestandTrainingZone
calculator
• View:GearRecommendations,GoalCadence,SessionTime,SessionProles.Optional
accessoriesallowupgradestoinclude,Speed,Cadence,HeartRate,Power(watts)
andCaloriesBurnt
www.jetblackcycling.com/app/rego_90
Usetheaboveuniquewebaddressto
registeryourdetailsandreceiveanemailwithlinksfor
downloadingtheapponyourpreferreddevice.
DOWNLOAD YOUR
FREE JETBLACK APP
Sport
MagTRAINER
ITEM CODE DESCRIPTION
JBT-35 JB Frame bushing (S1 Sport)
JBT-15B JB Axle support cup Drive Side
JBT-15C JB Axle support cup Non-Drive-Side
JBT-32 JB Axle bolt With Axle Support Cup - Drive-Side (S1 Sport)
JBT-32B JB Axle bolt With Axle Support CUP - Non-Drive-Side (S1 Sport)
JBT-37 JB Foot For Trainer Base (S1 Sport)
JBT-22 JB Skewer For Trainer (not Pictured)
JBT-30 JB Resistance unit assembly (S1 Sport)
JBT-36 JB Resistance Unit Adjustment Bolt With Knob (S1 Sport)
S1 - TRAINER PARTS
JBT-36
JBT-30
JBT-37
JBT-15C
JBT- 13
JBT-32B
JBT-15B
JBT-32
www.jetblackcycling.com
[email protected]