JETWAY MI23 Series User manual

MI23 Series
User’s Manual
NO. G03-MI23-F
Revision: 2.0
Release date: June 14, 2023
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

ii
ENVIRONMENTAL SAFETY INSTRUCTION................................................................... iii
USER’S NOTICE ............................................................................................................. iv
MANUAL REVISION INFORMATION.............................................................................. iv
ITEM CHECKLIST........................................................................................................... iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD ............................................................................ 1
1-2 SPECIFICATION .................................................................................................... 2
1-3 LAYOUT DIAGRAM ............................................................................................... 4
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING................................................................................................. 10
2-2 CONNECTORS AND HEADERS............................................................................ 13
2-2-1 CONNECTORS......................................................................................... 13
2-2-2 HEADERS................................................................................................. 19
2-3 MAXIMUM VOLTAGE & CURRENT LIMIT............................................................. 23
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP................................................................................................. 24
3-2 BIOS MENU SCREEN............................................................................................ 25
3-3 FUNCTION KEYS................................................................................................... 26
3-4 GETTING HELP...................................................................................................... 26
3-5 MENU BAR ............................................................................................................ 27
3-6 MAIN MENU........................................................................................................... 27
3-7 ADVANCED MENU................................................................................................ 28
3-8 CHIPSET MENU..................................................................................................... 40
3-9 SECURITY MENU .................................................................................................. 43
3-10 BOOT MENU.......................................................................................................... 46
3-11 SAVE & EXIT MENU .............................................................................................. 47
3-12 MEBX..................................................................................................................... 48
TABLE OF CONTENT

iii
Environmental Safety Instruction
Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
0 to 40 centigrade is the suitable temperature. (The temperature comes from the
request of the chassis and thermal solution)
Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
2.0 First Edition June 14, 2023
Item Checklist
Motherboard
Cable(s)

1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
Intel®LGA1700 Socket supports 12th /13th Gen. Core Processor (Max. 65W TDPs
under 180A)
Support 2* DDR5 4800MHz SO-DIMM up to 64GB
MI23-Q670X/R680X series: total support up to 8* 2.5GbE RJ-45 LAN ports
MI23-H610X series: total support up to 6* 2.5GbE RJ-45 LAN ports
MI23-Q670X/R680X series: total support up to 2* USB3.2 (Gen.2), 2* USB3.2
(Gen.1), 4* USB2.0 ports
MI23-H610X series: total support up to 2* USB3.2 (Gen.2), 1* USB3.2 (Gen.1), 5*
USB2.0 ports
MI23-Q670X/R680X series: 4 * SATAIII (6Gb/s) ports with support for RAID 0, 1, 5,
10 mode & 2* M.2 (M-key) slots; 1* M.2 (E-key) & 1* M.2 (B-key) slot along with SIM
card holder; 1* sideway PCIE Gen.4 x4 slot
MI23-H610X series: 4 * SATAIII (6Gb/s) ports & 1* M.2 (M-key) slot; 1* M.2 (E-key) &
1* M.2 (B-key) slot along with SIM card holder
1 * internal HDMI port
Support JetBIOS SW back up tool for BIOS recovering
Support onboard TPM 2.0 (*optional)
Support Smart FAN function
Supports ACPI S3 Function
Compliance with ErP Standard
Support Watchdog Timer Technology

2
1-2 Specification
Spec
Description
Design
Mini-ITX form factor; 10-layers;
PCB size: 17.0x17.0cm
Chipset
MI23-H610X Series: Intel H610E Chipset
MI23-Q670X Series: Intel Q670E Chipset
MI23-R680X Series: Intel R680E Chipset
CPU Socket
Intel LGA 1700 Socket supports 12th /13th Gen. Core™ i7 processors,
Intel®Core™ i5 processors, Intel®Core™ i3 processors, Intel®Pentium™
processors, Intel®Celeron™processors (Max.65W TDPs under 180A)
*Note: for detailed CPU support information please visit our website.
Memory Slot
2* DDR5 SO-DIMM slot
Support 2* DDR5 4800MHz SO-DIMM up to 64GB
Support dual channel function
*Note: MI23-R680X series support ECC.
Expansion
Slot
*PCIE2:1* PCIE Gen.4 x4 slot by sideway
*Note: 1.PCIE2 slot is only available to MI23-Q670X/R680X series;
2.PCIE2 can be expanded to support up to 4* PCIe signal 4 by1 slots
(At present, this function only supported by ETC4G adapter card).
M2E1:1* M.2 E-key,type-2230, USB2.0/PCIe x1 interface supports CNVi
M2B1:1* M.2 B-key, type-3042,USB3.2 Gen.1/USB2.0/PCIe x1 interface
supports 4G Module
SIMCARDB1:Nano-SIM card slot;co-function with M2B1 slot
Storage
SATA1/2/3/*4: 4*SATAIII 6Gb/s port (*SATA4 shares with M2M1)
*Note: MI23-Q670X/R680X series support RAID 0/1/5/10 mode.
M2M1: 1* M.2 M-key,type-2280 slot (for MI23-Q670X/R680X series:
PCIe Gen.4 x4 supports NVMe w/SATA interface; for MI23-H610X
series: only SATA interface only).
*M2M2:1* M.2 M-Key,type-2242/2280 slot (PCIe Gen.4 x4 supports
NVMe w/SATA interface )
*Note: M2M2 slot is only available to MI23-Q670X/R680X series.
LAN Chips
MI23-Q670X/R680X: 1* Intel i225-LM 2.5GbE + 7* Intel i225-V 2.5GbE
MI23-H610X: 6* Intel i225-V 2.5GbE
*Note: 2500Mbps high-speed transmission rate is only supported over CAT

3
5e UTP cable.
Graphics
Intel UHD Graphics
BIOS
AMI 256M Flash ROM
Multi I/O
Rear Panel I/O:
1* Power on/off button
1* Power LED & 1* HDD LED
1* RJ-45 RS232 COM port
MI23-Q670X/R680X: 2* USB 3.2 Gen.2 port & 2* USB 3.2 Gen.1 port
MI23-H610X: 2* USB 3.2 Gen.2 port & 1* USB 3.2 Gen.1 port +1* USB
2.0 port
MI23-Q670X/R680X: 8* 2.5GbE RJ-45 port
MI23-H610X: 6* 2.5GbE RJ-45 port
Internal I/O Connectors & Headers:
1 *24-pin main power connector
1 *4-pin 12V power connector
1* CPUFAN connector & 1* SYSFAN connector
1* CMOS battery connector
1* Front panel header
1* HDMI header
2* RS232 COM port header
2 * 9-Pin USB 2.0/1.1 header for 4* USB 2.0/1.1 port
2* LAN Status LED header
1* GPIO header
1* PS2 Keyboard & Mouse header
1* SMBUS header
TPM 2.0
Optional for MI23-R6802, MI23-Q6702 & MA20-H6102 Series
OS Support
for detailed OS support information please visit our website for latest
update

4
1-3 Layout Diagram
Rear IO Diagram
For MI23-Q670X / MI23-R680X Series:
For MI23-H610X Series:
Power Button
Power LED
HDD LED
USB 3.2 (Gen.2)
Ports
RJ-45 RS232
COM Port
USB 2.0 Port
USB 3.2 (Gen.1)
Port
Power Button
Power LED
HDD LED
USB 3.2 (Gen.2)
Ports
RJ-45 RS232
COM Port
USB 3.2 (Gen.1)
Ports
RJ-45 LAN Ports
(2.5 GbE)
RJ-45 LAN Ports
(2.5 GbE)

5
Motherboard Internal Diagram-Front
MI23-Q670X/R680X Series:
* Note: PCIE2 can be expanded to support up to 4* PCIe signal 4 by1 slots (At present, this function only
supported by ETC4G adapter card series).
LGA1700
CPU Socket
HDMI Header
PCIE2: Sideway
PCI Express Gen4x4 Slot
Front Panel
Header
GPIO
Header
M.2 M-Key Slot
(M2M1)
M.2 M-Key Slot
(M2M2)
USB2.0 Port
Headers
RS232 Serial Port Headers
(FP_COM2/3)
LAN_LED1 Header
LAN_LED2 Header
M.2 B-Key Slot
(M2B1)
M.2 E-Key Slot
(M2E1)
PS/2 KBMS Header
SATAIII Ports
(SATA1/2/3/4)
SMBUS Header
SYSFAN
CPUFAN
*Rear IO
Connector
(Refer to Page-4)
DDR5
SODIMM Slot x 2
BATCON
ATX 12V
Power Connector
ATX Main Power
Connector

6
Motherboard Internal Diagram-Front
MI23-H610X Series:
LGA1700
CPU Socket
ATX 12V
Power Connector
ATX Main Power
Connector
HDMI Header
Front Panel
Header
GPIO
Header
M.2 M-Key Slot
(M2M1)
USB2.0 Port
Headers
RS232 Serial Port Headers
(FP_COM2/3)
LAN_LED1 Header
LAN_LED2 Header
M.2 B-Key Slot
(M2B1)
M.2 E-Key Slot
(M2E1)
PS/2 KBMS Header
SATAIII Ports
(SATA1/2/3/4)
SMBUS Header
SYSFAN
CPUFAN
*Rear IO
Connector
(Refer to Page-4)
DDR5
SODIMM Slot x 2
BATCON

7
Motherboard Internal Diagram-Back
*Note: 1. SIM card slot (only workable along with M.2 B-key slot); 2. PCIE2 sideway PCI Express Gen.4
x4 slot (only on MI23-Q670X/R680X) can be expanded to support up to 4* PCIe signal 4 by1 slots (At
present, only supported by ETC4G adapter card series ); 3. M2M2 Slot (only on MI23-Q670X/R680X).
*SIMCARDB1

8
Motherboard Jumper Position
*Note:The diagrams in the manual are mostly taken from MI23-Q670X/R680X series unless otherwise
stated.
JBAT
JPCOM1
COPEN
JPME_DIS
JAT_ATX
JP80P

9
Connectors
Connector
Name
RJ45_COM1
RJ-45 COM Port Connector for Console
USB31
USB 3.2 (Gen.2) Port X2
MI23-Q670X/R680X: USB32
USB 3.2 (Gen.1) Port X2
MI23-H610X: USB32
Top: USB 2.0 Port
Bottom: USB 3.2(Gen.1) Port
LAN1-4
2.5 GbE RJ-45 LAN Port X4
MI23-Q670X/R680X: LAN5-8
2.5 GbE RJ-45 LAN Port X4
MI23-H610X: LAN5-8
2.5 GbE RJ-45 LAN Port X2
ATXPWR1
Main Power Connector
ATX12V
Internal 12V Power Connector
SATA1/2/3/4
SATAIII Connector
CPUFAN
CPU Fan Connector
SYSFAN
System Fan Connector
BATCON
CMOS Battery Connector
Headers
Header
Name
Description
Pitch
JW_FP
Front Panel Header(PWR LED/ HD
LED/Power Button /Reset)
9-pin Block
2.54mm
HDMI1
HDMI Port Header
19-pin Block
2.0mm
FP_COM2/3
RS232 Serial Port Header
9-pin Block
2.0mm
FP_USB21/22
USB2.0 Port Header X2
9-pin Block
2.0mm
LAN_LED1
LAN Status LED Header
8-pin Block
2.54mm
MI23-Q670X/R680X:
LAN_LED2
LAN Status LED Header
8-pin Block
2.54mm
MI23-H610X:
LAN_LED2
LAN Status LED Header
4-pin Block
2.54mm
GPIO
GPIO Port Header
10-pin Block
2.0mm
PS2KBMS
PS2 Keyboard & Mouse Header
6-pin Block
2.0mm
SMBUS
SMBUS Header
5-pin Block
2.0mm

10
Jumper
Jumper
Name
Description
Pitch
JPCOM1
RJ45_COM1 Port Pin-5 VCC Select
4-pin Block
2.0mm
JPME_DIS
ME Disabled
2-pin Block
2.0mm
COPEN
Case Open Message Display Function
2-pin Block
2.54mm
JAT_ATX
ATX Mode / AT Mode Select
3-pin Block
2.0mm
JBAT
Clear CMOS RAM Settings
3-pin Block
2.0mm
JP80P
GPIO Header Function Select
2-pin Block
2.0mm
Chapter 2
Hardware Installation
2-1 Jumper Setting
JPCOM1 (4-pin): RJ45_COM1 Port Pin5 VCC Select
JPCOM1 → RJ45_COM1 Pin5 VCC Select
1
3
5
2
4
6
1
3
5
2
4
6
1
3
5
2
4
6
2-4 Closed:
Pin5=NC;
3-4 Closed:
Pin5= +5V;
6-4 Closed:
Pin5=+12V.
*Note: Please make sure you set Pin (2-4) of Jumper JPCOM1 as closed from beginning or
you will cause the short circuit with the general Console cable to RJ45-COM1 port (refer to
page-14).
JPCOM1
RJ45_COM1

11
JPME_DIS(2-pin): ME Features Select
Pin1
JPME_DIS
→
ME Disable
Pin1
1-2 Closed: Disable ME Features.
1-2 Open: Nornal;
COPEN (2-pin): Case Open Message Display Function
Pin1
COPEN
→ Case Open Detection
CASE OPEN
GND
Pin 1-2 Short:When Case open function pin short to GND, the Case open function was detected.
When Used, needs to enter BIOS and enable ‘Case Open Detect’function. In this case if your
JPME_DIS
COPEN

12
case is removed, next time when you restart your computer, a message will be displayed on
screen to inform you of this.
JAT_ATX (3-pin): AT Mode /ATX Mode Select
1
3
1
3
JAT_ATX
→
ATX/AT Mode Select
1-2 Closed: ATX Mode Selected;
2-3 Closed: AT Mode Selected.
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
JBAT (3-pin): Clear CMOS RAM Settings
1
3
1
3
JBAT → Clear CMOS RAM Settings
1-2 Closed: Normal;
2-3 Closed: Clear CMOS.
JAT_ATX
JBAT

13
JP80P(2-pin): GPIO Header Function Select
Pin1
JP80P
→
GPIO Function Select
Pin1
1-2 Closed: Function as GPIO Port.
1-2 Open: Function as 80Port;
2-2 Connectors and Headers
2-2-1 Connectors
Rear I/O Back Panel Connectors
Icon
Name
Function
Power Button
For user to power on/off the system.
RJ-45 RSS232
COM Port
This connector is a RJ-45 COM port for console
function.
USB 3.2 (Gen.2)
Port
To connect USB keyboard, mouse or other
devices compatible with USB 3.2 (Gen.2)
specification. Ports support up to 10Gbps data
transfer rate.
JP80P

14
USB 2.0 Port
To connect USB keyboard, mouse or other
devices compatible with USB 2.0 specification.
USB 3.2 (Gen.1)
Port
To connect USB keyboard, mouse or other
devices compatible with USB 3.2 (Gen.1)
specification. Ports support up to 5Gbps data
transfer rate.
2.5Gbps
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for
Network connection which
supports10/100/1000/2500 Mbps Ethernet data
transfer rate. (*Note: 2.5Gbps is only supported
with CAT 5e UTP cable).
(1) RJ45_COM1(8-pin block): RJ-45 COM Port Connector for Console
Pin8
Pin1
RJ45_COM1
Pin No.
Definition
1
RTS
2
DTR
3
TXD
4
GND
5
GND/+5V/+12V
6
RXD
7
DSR
8
CTS
RJ45_COM1

15
(2) 2.5 Gbps RJ-45 Ethernet LAN Port Connector
LAN1/LAN2/ LAN3/LAN4/ LAN5/ LAN6/* LAN7/* LAN8
2.5Gbps RJ-45 LAN port LED Signals:
** There are two LED next to the LAN port. Please refer to the table below for the LAN
port LED indications.
Activity/Link
LED
Speed
LED
A
B
A: Activity/Link LED
Status
Description
Off
No Link
Blinking
Data Activity
On
Link
B: Speed LED
Status
Description
Off
10/100Mbps connection
Orange
1Gbps connection
Green
2.5Gbps connection
*Note:.2.5Gbps high-speed transmission rate is only supported over CAT 5e UTP cable;
MI23-Q670X/R680X Series: total support 8* 2.5GbE RJ-45 port;
MI23-H610X Series: total support 6* 2.5GbE RJ-45 port(without LAN7/LAN8).
LAN1
LAN2
LAN3
LAN4
LAN5
LAN6
*LAN7
*LAN8