JICCODA LE-1 User manual

QUICK INSTALL GUIDE
LE-1
Laser Engraving Machine
10

Contents
•Package list check ------------------------------------------------------------------------------------------------------------2
•Set up LE-1------------------------------------------------------------------------------------------------------------------------4
•Download and install software -------------------------------------------------------------------------------------------34
•Safety guidelines---------------------------------------------------------------------------------------------------------------42
•One year warranty-------------------------------------------------------------------------------------------------------------43
1

Rear rail *1
X Rail *1
Right Side Rail *1
Left Side Rail *1
Front rail *1
Y Endstop *1 Tensioner Assembly *1
Control Board *1Laser Module *1
L Motor assembly *1 R Motor assembly *1 X Sliding Assembly *1 X Endstop *1 L-angle bracket *4
Y Drag Chain Support *1
Drag chain bracket *1 X Drag Chain Bracket *1 Frame Foot *3 White Nylon Tubes 25 *2
PT.1 Package list check
2

X Synchronous Belts *1
Y Synchronous Belts *2 24V Adapters *1 Power cable *1
Protective glasses *1 USB cable *1
Measuring tools *1
Tool Kit *1
Belt Screws *4
M5x55 Screw *1 M4x8 Screws *8
M3x6 Screws *14 M3x8 Screws *7 M5x18 Screws *5
M5x20 Screws * 11 M5x25 Screws *1 M5x8 Screws * 6
PT.1 Package list check
3

Parts Required:
•M3x6 Screws *2
•Drag chain bracket *1
•R Motor assembly *1
Step 1
Align the holes as shown and secure with M3x6
screws.
Drag chain bracket *1
PT.2 set up LE-1
4

Parts Required:
•Right Side Rail *1
•Assembly (Step 1) *1
Step 2
Identify the Right Side Rail by the scale on the
surface and the orientation of the hole.
Slide the Assembly (Step 1) assembly into the
Right Side Rail, following the direction of the
arrow in the diagram.
1/2
PT.2 set up LE-1
5

Parts Required:
•Assembly (Step 2) *1
Step 2
If the assembly is very loose in the Rail, use a
hexagonal spanner to adjust the rollers as
shown by the arrows in the picture.
2/2
PT.2 set up LE-1
6
Notes：
1. The same set of rollers are
adjusted at the same time.
2. Optimum looseness: the POM
wheels rub slightly against the guide
rails as they turn.

Parts Required:
• Assembly (Step 2) *1
•Y Synchronous Belts *1
•Belt Screws *2
Step 3
3.1 Belt screw slides in through the guide slot (in
the direction of the arrow)
3.2 The belt is placed under the belt screw and
the screw is tightened
3.3 Belt wraps around the gear on the motor (as
shown)
3.4 Tighten the belt and tighten the other section
of the spray belt screw (position as shown)
PT.2 set up LE-1
7
Note: Do not cover the screw holes in the guide rails,
otherwise the screws will not be installed in the next step.

Parts Required:
• Assembly (Step 3) *1
•Y Endstop *1
•M5x20 Screws *1
Step 4
Stick flat on the bottom of the rail and fix with
M5x20 screws.
PT.2 set up LE-1
8
Note the direction of installation

Parts Required:
• Left Side Rail *1
•L Motor assembly *1
Step 5
Identify the Right Side Rail by the scale on the
surface and the orientation of the hole.
Slide the L Motor assembly into the Right Side
Rail, following the direction of the arrow in the
diagram.
1/2
PT.2 set up LE-1
9