JK Audio RemoteAmp Blue User manual

JK Audio
RemoteAmp™
Headphone Amplier
User Guide

ii RemoteAmp Headphone Amplier
Welcome
Thank You
Thank you for purchasing the
JK Audio RemoteAmp™. Please read
this guide for instructions on using it.
Getting Assistance
If you have technical or application
questions:
In the US & Canada, call us toll free
at: 800-552-8346
All other countries dial: 815-786-2929
(M-F 8:30-5:00pm Central Time Zone)
Email us at: [email protected]
Or, check out our FAQ section for
answers to common questions.
Limited Warranty
RemoteAmp is covered by a 2 year
warranty to be free from defective
workmanship and materials. To obtain
service, contact JK Audio by phone
or email for return authorization.
Once authorized, you will carefully
pack and ship the faulty product and
all accessories to us. You will pay
for shipping to us and we will pay for
return back to you.
This warranty does not cover
damages due to accident, weather,
re, ood, earthquake, misuse,
unauthorized repairs or modications,
or damages occurred in shipping, only
defective workmanship or materials.
There are no expressed or implied
warranties which extend beyond
the warranty here made.

Contents iii
Safety Precautions
Use Caution to Prevent
Hearing Loss
RemoteAmp contains a headphone
amplier that is more powerful than
the typical consumer product.
JK Audio products are designed for
the broadcast industry. The broadcast
professional must be able to hear
headphone signals over the ambient
noise level. From the cheering crowd
at a football game to trackside at a
car race, the program material or cues
must be heard at high volumes without
distortion.
Road Safety
Never use headphones while driving
or cycling, etc. It can be dangerous
to turn up the volume even while
walking. Doing so may hinder your
hearing and can be hazardous on the
roadways or at pedestrian crossings.
Note: While RemoteAmp was designed
to be very rugged and durable, it is not
waterproof and care should be taken to
keep the unit dry.

iv RemoteAmp Headphone Amplier
XLR Line level Input
XLR Line In Volume Control
1/4" Stereo Headphone Jack
1/8" (3.5mm) Earpiece Jack
Battery Test Indicator
Stainless Steel Belt Clip
>20 Hours on one 9V Battery
Features
Overview 1
Setup 2
Operation 4
FAQs 5
Technical Information 7
Welcome

Overview 1
Introducing RemoteAmp
The RemoteAmp is a simple
battery-powered personal headphone amplier. Use
the RemoteAmp as an IFB earpiece or headphone
amplier, or as an on-stage monitor headphone
amplier. This low-distortion, 1 watt amplier will cut
through the crowd noise without distortion.
Overview

2RemoteAmp Headphone Amplier
Input
The input XLR accepts line level
signals from your mixer, distribution
amplier or phone line hybrid.
The balanced input XLR is wired:
Pin 1 Pin 2 Pin 3
Ground Signal + Signal -
This is a transformer balanced input.
If you are using an unbalanced
source, you must connect your
signal lead to pin 2 and then connect
your ground to pins 1 and 3. Do
not connect a powered input to this
device.
Setup
1/8" Output
The 1/8” earpiece jack is current
limited to prevent excessive signals
into your earpiece. This mono jack will
power earpieces with an impedance of
150 ohms or greater. If you would like
to use light-weight stereo headphones
that are typically 8 to 36 ohms, wired
with a 1/8" stereo jack, you will need
to use an adapter to plug into the 1/4"
stereo headphone jack. Or you can
solder a jumper wire across the top of
the 150 ohm resistor, R2.

Overview 3
Setup
1/4" Output
The 1/4” headphone jack is wired
for either a stereo or mono plug. If a
stereo headphone plug is used, you
will hear signal in both the left and
right ears.
A 1/4" mono plug can also be used
without any problem, however, if
you plan to always use a 1/4" mono
plug, you might consider a simple
modication to the RemoteAmp
resistor R3.
R3 Modication (Mono)
Resistor R3 provides signal to the
"ring" of tip-ring-sleeve. If you clip one
of the leads on R3, you will disable
stereo operation and increase the
power available to the left or mono
output. Another common solution is to
wire your headphones with a stereo
headphone plug but wire both ears
to the left channel (the tip of the plug)
and leave the ring unconnected. This
has the same effect as clipping the
resistor on RemoteAmp.

4RemoteAmp Headphone Amplier
Gain Adjustment
Behind the back cover of the
RemoteAmp you will nd a jumper
on the circuit board which allows you
to adjust the maximum amount of
gain the RemoteAmp delivers. In the
factory default open position you will
receive a maximum of 25 dB gain. If
the jumper is set to the optional closed
position, a maximum of 40 dB gain will
be delivered.
Operation
Battery
An alkaline battery is strongly
recommended. The battery test
indicator shows the strength of the
battery power remaining. A bright
light indicates plenty of power, a dim
light reminds you to be prepared with
a fresh battery. Once the LED stops
responding to the test switch, you
will begin to hear signal breakup and
distortion as the battery is drained
of its last breath which may mean
minutes or hours depending on the
circumstances.

FAQs 5
Will the RemoteAmp work
with my QuickTap IFB?
Yes. The RemoteAmp will take the
balanced output from the QuickTap
IFB and send it to a 1/4" headphone
jack as well as a 3.5 mm mini jack.
You can now use headphones, an
earpiece or both.
Can I get more gain out of my
RemoteAmp?
Yes. Take the back off of the
RemoteAmp. You will nd a jumper
which will give you enough gain to
boost a healthy microphone level
signal to headphone level output.
FAQs

RemoteAmp Headphone Amplier
Block Diagram
6
XLR
Input
Output
Level
1/4" Out
1/8" Out

Technical Information 7
Line Input
Female XLR:
4k ohms /
100 mV RMS (-18 dBu nom, +12 dBu max)
Max Gain: 46 dB
Output
1/4" Mono/Stereo: 8 ohms, 1 Watt max
1/8" (3.5mm) Mono: 150 ohms, 100 mW nom.
Misc.
Frequency Response: 30 Hz - 20 kHz ± 1 dB
Power: One 9 volt Alkaline Battery
Size: 5.1" x 2.7" x 1.3" (13 x 6.9 x 3.3 cm)
Weight: 10 oz. (275 g)
Specications
Technical Information

JK Audio
JK Audio, Inc.
1311 E 6th St.
Sandwich, IL 60548
United States
Telephone: [phone]
Toll Free: 1.800.jkaudio
Fax: [phone]
www.jkaudio.com
© 2016 JK Audio, Inc. All rights reserved.
RemoteAmp™
Headphone Amplier
User Guide Version 5/25/16