JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2 User manual

INSTALLATION GUIDE
for the
SB-F-150-SPRCRW/13TW5v2
SKU# 94460 - 94462
2009 & Up Ford F150 SuperCrew
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary tools
and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your
own installation, please read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox®be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
Continued on Next Page
SB-F-150-SPRCRW/13TW5v2 INSTR_SKU# 011297
INSTALLATION
DIFFICULTY:
25
OUT
OF
ESTIMATED TIME:
1 HOUR
SPECIFICATIONS
Enclosure Type: Sealed
Driver Type: 13T W5v2-2
Nominal Impedance: 2 ohms
Continuous Power Handling: 600 watts (RMS method)
INCLUDED HARDWARE
(4) Enclosure Bracket
(4) 1/4 - 20 x 1-1/2” Hex Drive Bolt
(4) 3” x 3” Wax Square
(4) 3/8” Flat Washer
(4) 3/8 - 16 x 1-3/4” Hex Bolt
(4) 3/8” Fender Washer
(4) 3/8” Split Lock Washer
(4) 3/8 - 16 Hex Nut
(1) Trim Panel
(1) #8 x 1” Self Tap Screw

SB-F-150-SPRCRW/13TW5v2 INSTR_SKU# 011297
POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio XD600/1v2. The diagram below shows the recommended crossover settings for the XD600/1v2. For a detailed description of the amplier settings,
consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplier. Other kits
are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplier. JL Audio
recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next PagePage 2 • JL Audio, Inc., 2016

Continued on Next Page
SB-F-150-SPRCRW/13TW5v2 INSTR_SKU# 011297
Page 3 • JL Audio, Inc., 2016
STEP 4
Unplug and remove the enclosure.
STEP 8
Slide a Wax Square under each of the Enclosure Brackets as
shown.
STEP 3
Unclip the bolt covers and remove the three bolts holding in
the enclosure.
STEP 7
Fold the driver’s side rear seat down and align the
Stealthbox® with the edge of the inner side of the seat.
In 2015 models, the plastic storage divider panel can be
removed to allow the Stealthbox® to slide completely under
the seat, if desired.
STEP 2
Fold the rear seats up to access the factory subwoofer
enclosure.
STEP 6
Repeat for the opposite side.
STEP 1
Empty out the back seat area.
STEP 5
Attach two Enclosure Brackets to the threaded inserts on the
Stealthbox® using a pair of 1/4 - 20 x 1-1/2” Hex Drive Bolts as
shown.

Continued on Next Page
SB-F-150-SPRCRW/13TW5v2 INSTR_SKU# 011297
STEP 12
Using a 3/8” drill bit, drill through the hole locations marked
in the previous step.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a reduction
in your weekly pay.
Always wear eye protection when drilling!
STEP 16
Repeat for the opposite side. Connect speaker cable to the
terminal cup on the Stealthbox® and route as necessary.
ST EP 11
Align an Enclosure Bracket with each of the impressions in
the Wax Squares, and mark the hole location as shown.
STEP 15
Put the Stealthbox® back into the vehicle and secure the
Enclosure Brackets to the enclosure with a pair of 1/4 - 20 x
1-1/2” Hex Drive Bolts as shown.
STEP 10
Press down firmly on the Stealthbox® to leave impressions
of the Enclosure Brackets on the Wax Squares. Remove
the enclosure, leaving the Wax Squares stuck to the floor.
Remove the Enclosure Brackets from the Stealthbox®.
STEP 14
From under the vehicle, place a 3/8” Fender Washer, a 3/8”
Split Lock Washer, and a 3/8” Hex Nut on each of the 3/8 - 16
x 1-3/4” Hex Bolts, and firmly tighten.
STEP 9
Repeat for the opposite side.
STEP 13
Slide a 3/8” Flat Washer over a 3/8 - 16 x 1-3/4” Hex Bolt, and
drop the assembly through each bracket and hole in the
floor.
Page 4 • JL Audio, Inc., 2016

SB-F-150-SPRCRW/13TW5v2 INSTR_SKU# 011297
Page 5 • JL Audio, Inc., 2016
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will t in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 5 x 7”- Front Doors
Fits JL Audio Models: TR570-CXi, C2-570x, C3-570,
C5-570x, & C5-570
Rear Speaker Size / Location: 5 x 7”- Front Doors
Fits JL Audio Models: TR570-CXi, C2-570x, C3-570,
C5-570x, & C5-570
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve”and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011297 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
STEP 19
Fold the carpeted flap back down to conceal the screw, and
fold the seat back down.
STEP 18
Secure the Trim Panel to the Stealthbox® with a #8 x 1” Self
Tap Screw.
STEP 17
Align the Trim Panel with the Stealthbox®. Lift the carpet
flap to access the hole in the panel. Using a 1/8” drill bit, drill
through the hole in the Trim Panel and into the Stealthbox®
as shown.
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!