JL Audio SB-CAN-MVCM1/10TW3 User manual

Continued on Next Page
SB-CAN-MVCM1/10TW3 INSTR_SKU# 011450
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
D IFFI CU LT Y:
ESTIMATED TIME:
12 HOURS
25
OUT
OF
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
INSTALLATION GUIDE
for the
SB-CAN-MVCM1/10TW3
SKU# 94623
2015 & Up CanAm Commander, Commander Max,
Maverick X, & Maverick Max

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2016
SB-CAN-MVCM1/10TW3 INSTR_SKU# 011450
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
BOM ID Qty SKU Description
1 1 153690 Le Bracket
2 3 153729 1/4 - 20 x 1” Stainless Steel Serrated Flange Bolt
3 1 153689 Bottom Bracket
4 1 153691 Right Bracket
- 1 150249 Foam Strips (not shown)

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX300/1. The diagram below shows the recommended crossover settings for the MX300/1. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using an 8 AWG power kit such as the XD-PCS8-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as the XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2016
SB-CAN-MVCM1/10TW3 INSTR_SKU# 011450

Page 4 • JL Audio, Inc., 2016 Continued on Next Page
STEP 8
Remove the indicated factory nut. This nut and
accompanying bolt will be used to secure the
Bottom Bracket in Step 15.
STEP 7
Behind the plastic panel, remove the indicated
factory nut. This nut and accompanying bolt
will be used to secure the Left Bracket in Step
10.
STEP 6
From behind the right front tire, remove the
two indicated factory bolts, and pull back the
plastic panel.
STEP 5
Remove the glove compartment from the
vehicle.
STEP 4
Remove the two factory bolts above the glove
compartment.
STEP 3
Carefully unclip the plastic trim panel above
the glove compartment, and remove the panel
from the vehicle.
STEP 2
Open the glove compartment and fold the
door down.
STEP 1
Empty the passenger side of the vehicle.
SB-CAN-MVCM1/10TW3 INSTR_SKU# 011450

Page 5 • JL Audio, Inc., 2016 Continued on Next Page
STEP 16
Fully tighten all three 1/4 - 20 x 1” Stainless
Steel Serrated Flange Bolts.
Route speaker cable as necessary.
STEP 15
Secure the Bottom Bracket to the vehicle using
the factory bolt and nut removed in Step 8.
Thread a 1/4 - 20 x 1” Stainless Steel Serrated
Flange Bolt through the hole in the Bottom
Bracket, into the threaded insert on the bottom
of the enclosure, and hand tighten.
STEP 14
Thread a supplied 1/4 - 20 x 1” Stainless Steel
Serrated Flange Bolt through the hole in the
Left Bracket, into the threaded insert on the
bottom of the enclosure, and hand tighten.
STEP 13
Thread a supplied 1/4 - 20 x 1” Stainless Steel
Serrated Flange Bolt through the slotted hole
in the Right Bracket, into the threaded insert
on the side of the enclosure, and hand tighten.
STEP 12
Connect speaker cable to the barrier strip on
the Stealthbox®, and slide the enclosure into
place over the Left Bracket.
ST EP 11
Secure the Right Bracket to the vehicle using
the factory nuts and bolts removed in Step 9.
STEP 10
From inside the vehicle, remove the indicated,
upper factory bolt, and use it to secure the top
of the Left Bracket to the vehicle as shown.
Secure the bottom of the Left Bracket using the
factory bolt and nut removed in Step 7.
STEP 9
Remove the two indicated factory bolts. These
bolts and accompanying nuts will be used to
secure the Right Bracket in Step 11.
SB-CAN-MVCM1/10TW3 INSTR_SKU# 011450

Page 6 • JL Audio, Inc., 2016
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
SB-CAN-MVCM1/10TW3 INSTR_SKU# 011450
STEP 18
Reinstall the plastic trim panel above the glove
compartment.
Note: For optimum performance, we
recommend applying the included Foam Strips
(or sound damping material) to surrounding
plastic panels to reduce unwanted vibrations.
STEP 17
Reinstall the glove compartment using the
factory bolts removed in Step 4.
MID/HIGH FREQUENCY DRIVER FITMENT
VeX™ Enclosed Speaker Systems are ideal for powersports and o-road vehicle applications. Each
weatherproof pod can be mounted to a roll cage precisely aimed for optimum sound. Mounting
xtures are available to t a variety of roll cage diameters.
[phone]
www.jlaudio.com
JLA-SKU# 011450 • ver. 09.16.2016 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc.“Ahead of the
Curve”, its respective logo, and “How we play” are trademarks of JL Audio, Inc.
Printed in USA • ©2016 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.