JL Audio SB-CAN-MVX3/10TW3 User manual

INSTALLATION GUIDE
for the
SB-CAN-MVX3/10TW3
SKU# 94646
2017 & Up Can-Am Maverick X3 (2-seat)
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
D IFF I CU LT Y:
ESTIMATED TIME:
2 HOURS
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
Continued on Next Page
25
OUT
OF
SB-CAN-MVX3/10TW3 INSTR_SKU# 011492

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2017
SB-CAN-MVX3/10TW3 INSTR_SKU# 011492
BOM ID Qty SKU Description
1 6 151709 1/4 - 20 x 1-1/2” Socket Cap Screw
2 6 150066 1/4” Split Lock Washer
3 6 153734 1/4” Flat Washer
4 2 153764 Stainless Steel Cushion Clamp
5 1 152431 Template
- 1 150249 Foam Tape (not shown)
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX300/1. The diagram below shows the recommended crossover settings for the MX300/1. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2017
SB-CAN-MVX3/10TW3 INSTR_SKU# 011492

Page 4 • JL Audio, Inc., 2017 Continued on Next Page
STEP 8
Remove the Template from the vehicle.
Using a 1/8” drill bit, drill a pilot hole through
each of the marks made in the previous step.
STEP 7
Using a small pick tool, mark each of the hole
locations through the Template onto the
plastic floor panel.
STEP 6
Position the Template on the vehicle floor. Push
the Template forward and to the outside, as
shown, until flush with the frame rails.
STEP 5
Unplug the seat belt wiring harness.
Carefully remove the driver’s seat from the
vehicle.
STEP 4
Remove the seat belt bolt.
STEP 3
Slide the driver’s seat forward.
Remove the two rear seat bolts from the seat
bracket.
STEP 2
Remove the two front seat bolts from the
driver’s seat bracket.
STEP 1
Empty the front of the vehicle.
SB-CAN-MVX3/10TW3 INSTR_SKU# 011492

Page 5 • JL Audio, Inc., 2017 Continued on Next Page
STEP 16
Slide a 1/4” Split Lock Washer and a 1/4” Flat
Washer over each of four 1/4 - 20 x 1-1/2”
Socket Cap Screws.
From under the vehicle, pass each assembly
through a drilled hole in the floor panel, into a
threaded insert in the bottom of the enclosure,
and fully tighten.
STEP 15
Tighten the eight subwoofer mounting screws.
STEP 14
Push the enclosure forward, allowing it to drop
into position. Place the subwoofer back into
the enclosure.
STEP 13
Partially lift the subwoofer out of the enclosure,
as shown. This allows for clearance to position
the enclosure in the next step.
STEP 12
Carefully set the enclosure into the vehicle, as
shown.
STEP 11
Completely loosen the eight subwoofer
mounting screws, but do not remove them.
STEP 10
Place the Stealthbox® face down on a flat
surface. Attach Foam Tape to the bottom of the
enclosure, as shown.
STEP 9
Using a 5/16” drill bit, enlarge each of the pilot
holes drilled in the previous step.
SB-CAN-MVX3/10TW3 INSTR_SKU# 011492