JL Audio StealthMod SMS-B-X5E70 User manual

INSTALLATION GUIDE
for the
SMS-B-X5E70
SKU# 94518
2007 - Up
Thank you for choosing a JL Audio StealthMod®for your automotive sound system. With
proper installation, your new vehicle-specific enclosed subwoofer system will deliver
years of listening pleasure.
We strongly recommend that you have your new StealthMod®system installed by your
authorized JL Audio dealer. The installation professionals employed by your dealer have
the necessary tools and experience to disassemble and reassemble your vehicle properly.
Also, keep in mind that your warranty coverage extends to 2 years if your system is
installed or approved by your authorized JL Audio dealer. If you prefer to perform your
own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that the
StealthMod®system be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
STEP 1
Roll down the window and open the passenger door.
Continued on Next Page
STEP 2
Carefully pry up on the trim piece around the release handle
and remove it from the vehicle.
STEP 3
Remove the screw behind the panel.
SMS-B-X570 INSTR_SKU# 11339
INSTALLATION
DIFFICULTY:
55
OUT
OF
ESTIMATED TIME:
45 HOURS
StealthMod ®

Continued on Next Page
SMS-B-X5E70 INSTR_SKU#11339
STEP 7
With the door panel removed, unclip the front of the upper
door trim as shown.
STEP 6
Remove the two screws on the underside of the door panel.
Starting at the bottom, unclip the door panel from the door,
unplug the wiring harnesses, and remove the door panel
from the vehicle.
STEP 5
Remove the two screws under the panel.
STEP 4
Carefully pry off the trim on the pull handle and remove it
from the vehicle.
Page 2 • JL Audio, Inc 2012
STEP 9
Pictured is the back side of the door panel. Cut a small
piece of the Foam Tape and apply it to the panel as shown.
Remove the screw indicated, and retain it for use in Step 11.
STEP 11
Slide a pair of Speed Clips over the holes in the Crossover
Bracket. Place the bracket over the two pieces of Foam
Tape, aligning the holes with the clip and speaker mounting
hole. Secure the bracket to the door panel with the screw
removed in Step 9.
STEP 10
Cut a second piece of the Foam Tape and apply it to the
panel, over the clip as shown.
STEP 8
Unclip the rear of the upper door trim as shown, and remove
the panel from the vehicle.

Continued on Next Page
SMS-B-X5E70 INSTR_SKU#11339
STEP 15
Reinstall the upper door trim with the tweeter wires exiting
from the bottom as shown. Extend the positive and
negative tweeter wires as necessary, and onnect them to the
Tweeter Output (T+ and T-) of the Crossover.
Plug in the factory harnesses and reinstall the door panel.
STEP 14
Mount the C5 Tweeter into the surface mount cup, and
install the assembly into the factory provision as shown. An
adhesive is recommended to secure the assembly. Reinstall
the foam with the tweeter wires exiting from the bottom.
STEP 13
Remove the foam from the upper door trim to access the
factory tweeter. Unclip and remove the tweeter.
STEP 12
Cut two more pieces of Foam Tape, and apply them to the
Crossover Bracket, then mount the Crossover to the bracket
using a pair of #8 x 3/4” Phillips Head Screws.
Cut the factory midrange wires with enough length to reach
the Crossover. Connect the White positive and White/Blue
negative wires from the factory midrange to the Woofer
Output (W+ and W-) of the Crossover. Connect the other
end of the cut factory midrange wires to the Input (In + and
In -) of the Crossover.
Page 3 • JL Audio, Inc 2012
STEP 17
Empty out the cargo area so that you have a clean area to
work in.
STEP 19
The tools can be relocated to the foam tray inside the spare
tire.
STEP 18
Remove the cargo floor panel. Remove the two screws on
the battery cover, and remove the cover. Remove the screw
holding in the storage tray, and remove the tray.
STEP 16
Repeat the Crossover and Tweeter installation for the driver’s
side beginning by following the procedure outlined in Steps
1-3.
Remove the screw from inside the door cup, and
carefully unclip the switch panel as shown. Unplug the
harnesses and remove the panel.
Continue by following the procedure outlined in Steps
6-15. The factory midrange has a Yellow positive wire and a
Yellow/Black negative wire.

Continued on Next Page
SMS-B-X5E70 INSTR_SKU# 11339
STEP 23
Remove the speed clip from the location indicated by the
left arrow, and relocate it to the location indicated by the
right arrow as shown.
STEP 22
Using a 1” hole saw, drill a hole at the intersection and slide
a U-Nut through the driled hole, aligning it with the factory
hole as shown.
STEP 21
Note: Steps 21-22 are only necessary on vehicles not
equipped with the factory bracket shown in Step 20.
Locate the two holes in the floor, and mark their
perpindicular intersection as shown.
STEP 20
Remove the nut from the factory bracket as shown. Retain
the nut for use in Step 26.
If this factory bracket isn’t present, substitute Steps 21-22.
Page 4 • JL Audio, Inc 2012
STEP 25
Using a pair of 1/4” - 20 x 1” Bolts, 1/4” Lock Washers, and 1/4”
Flat Washers, attach the Side Bracket to the Stealthbox® as
shown, and hand tighten.
STEP 26
Attach 12 AWG Speaker Cable to the Stealtbhox®, and place
the enclosure into position, aligning the hole in the Side
Bracket with the factory bolt as shown. Secure the Side
Bracket to the floor using the factory nut removed in Step
20.
On vehicles not equipped with the factory bracket and bolt,
secure the Side Bracket to the U-Nut installed in Step 22
using a 1/4 - 20 x 1/2” Bolt.
STEP 24
Pictured is the included hardware needed to mount the
enclosure, along with the factory nut removed from Step 20.
STEP 27
Slide the Stealthbox® as far back toward the rear of the
vehicle as possilbe. Using an open-ended wrench, tighten
the two 1/4” - 20 x 1” Bolts to secure the Side Bracket to the
Stealthbox®.

Continued on Next Page
SMS-B-X5E70 INSTR_SKU#11339
STEP 31
Remove the three clips that hold the storage pocket in place
and remove the pocket.
STEP 30
Remove the access door from the left side panel.
STEP 29
Secure the Top Bracket to the Stealtbox® and to the rail using
a pair of 1/4” - 20 x 1” Bolts, 1/4” Lock Washers, and 1/4” Flat
Washers.
STEP 28
Slide a U-Nut over the factory hole in the rail as indicated.
Page 5 • JL Audio, Inc 2012
STEP 33
Pictured is the cargo area with the left side panel removed.
Unplug the indicated factory amplifier plug for easier access
to the factory wiring in Steps 37-38.
STEP 34
Place four Speed Clips on the Amplifier Bracket as shown.
STEP 32
Remove the three clips that hold the side panel in place and
remove the panel.
STEP 35
Align the Amplifier Bracket to the factory studs as shown,
and secure it to the vehicle using three 5mm Hex Nuts as
indicated.

Continued on Next Page
SMS-B-X5E70 INSTR_SKU#11339
STEP 39
Extend the red ignition wire from the CL-SSI using the
supplied Remote Turn-on Wire, route it to the passenger side
of the cargo area, and connect it to the factory ignition wire
on the back of the accessory outlet. It’s recommended to
fuse the wire within a few inches of the connection.
Connect the yellow 12 volt power wire, the black ground
wire, and the blue remote turn-on wire of the CL-SSI to the
XD700/5 along with the main Red Power Wire and Black
Ground Wire as indicated on the amplifier.
STEP 38
Using the wire colors indicated in Step 37 as a guide,
connect the door wires from the factory amplifier plug to
the Input A of the CL-SSI. Connect the sub wires to the Input
B of the CL-SSI. Using the Speaker to RCA adapters and RCA
cables, connect the front outputs of the CL-SSI to the Inputs
1-2 of the XD700/5, and the rear outputs of the CL-SSI to
Inputs 3-4 of the XD700/5.
Extend the opposite side of the factory wires with 16 AWG
Speaker Cable as necessary, and connect the door wires
to Outputs 1-2 on the XD700/5. Connect the sub wires to
Outputs 3-4 on the XD700/5.
STEP 37
Cut the following factory wires approximately six inches
away from the factory amplifier plug:
LF Door (+) = Blue/Brown RF Door (+) = Blue/Brown
LF Door (-) = Blue/White RF Door (-) = Blue/Black
LF Sub (+) = Brown/Yellow RF Sub (+) = Brown/White
LF Sub (-) = Red/White RF Sub (-) = Red/Blue
Note: Pictured are plugs we added to easily return the
vehicle to its original condition. These are not necessary, nor
included with this StealthMod® kit.
STEP 36
Slide a Speed Clip over the factory hole as shown, and secure
the lower part of the bracket with a #8 x 3/4” Phillips Head
Screw.
Page 6 • JL Audio, Inc 2012
STEP 41
Route the Ground Wire to the factory ground location
indicated, and secure it using the factory bolt.
STEP 42
Route the Power Wire toward the battery. Connect the Fuse
Holder within 12” of the battery, and secure the the Power
Wire to the positive battery post. Install the Fuse into the
Fuse Holder.
STEP 40
Connect the 12 AWG Speaker Cable from the Stealthbox® to
output 5 on the XD700/5. Mount the amp to the Amplifier
Bracket using four #8 x 1” Phillips Head Screws. Plug in the
cable for the HD-RLC and route it to the desired level control
location. Follow the steps included with the HD-RLC for
mounting instructions.
STEP 43
Secure the CL-SSI with Velcro as shown. Be sure to leave it
accessible for adjusting the trim levels

Continued on Next Page
SMS-B-X5E70 INSTR_SKU#11339
STEP 47
Cut the Foam Tape into three 4” strips, affix them to the new
Battery Cover, and trim away the excess as shown.
STEP 46
Adjust the trim levels on the CL-SSI as outlined in its owner’s
manual. Set the amplifier crossover controls as shown in
the illustration at the end of this manual, and set the input
sensitivites on the amplifier as outlined in its owner’s manual.
Reinstall the side panel.
STEP 45
Reinstall the storage pocket.
STEP 44
Cut away the portion of the storage pocket indicated by the
tape.
Page 7 • JL Audio, Inc 2012
CONGRATULATIONS!
You have completed the installation for this model!
Enjoy your new StealthMod®!
STEP 48
Secure the Battery Cover using the three #8 x 1” Sheet Metal
Screws. Reinstall the floor panel.

SMS-B-X5E70 INSTR_SKU#11339
Page 8 • JL Audio, Inc 2012
INCLUDED HARDWARE
(1) 1/4 - 20 x 1/2” Bolt (4) #8 x 1” Phillips Head Screw (1) 12’ Blue Remote Wire
(4) 1/4 - 20 x 1” Bolt (3) #8 x 3/4” Phillips Head Screw (1) 6’ 12 AWG Speaker Wire
(4) 1/4” Flat Washer (9) Speed Clip (1) 12.5’ 16 AWG Speaker Wire
(4) 1/4” Lock Washer (1) Velcro
(2) 1/4 - 20 U-Nut (1) XD700/5
(1) Battery Cover (1) C5-075ct
(3) #8 x 1” Sheet Metal Screw (2) C5-525-XO
(1) Top Bracket (1) CL-SSI
(1) Side Bracket (1) XD-MFB-MAXI
(1) Foam Tape (1) XD-MAXI-60
(1) Amp Bracket (2) XD-CLRAIC2-3
(3) 5mm Hex Nut (2) XD-CLRAIC2-SW
(1) Left Crossover Bracket (1) 6’ Red Power Wire
(1) Right Crossover Bracket (1) 6’ Black Ground Wire
SPECIFICATIONS
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W3v3-2
Nominal Impedance: 2 ohm
Continuous Power Handling: 500 watts
POWER RECOMMENDATION
The diagram below shows the recommended crossover settings for the XD700/5.
The XD700/5 is a very versitile amplifier. Consult the owner’s manual for even more detailed
information about installing and tuning the amplifier.
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.“Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 94518 02.15.2012 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA