Jl audio Stealthbox sb-pol-rzg2/10tw3 User manual

Continued on Next Page

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the Stealthbox®be properly mounted to the vehicle

according to these instructions. Failure to mount the enclosure

properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a

collision or sudden deceleration.

INSTALLATION

D IFFI CU LT Y:

ESTIMATED TIME:

2 HOURS

OUT

Enclosure Type: Sealed

Driver Type: 10TW3-D4

Nominal Impedance: 2 ohms

Continuous Power Handling: 400 watts (RMS method)

INSTALLATION GUIDE

for the

SB-POL-RZG2/10TW3

SKU# 94620

2014 & Up Polaris RZR XP 1000, RZR XP 4 1000,

RZR 900 XC, & RZR 4 900

INCLUDED HARDWARE

Continued on Next Page

Page 2 • JL Audio, Inc., 2016

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

* Pre-installed on enclosure

BOM ID Qty SKU Description

1 4 153729 1/4 - 20 x 1” Stainless Steel Serrated Flange Bolt

2 1 153678 Side Bracket

3* 5 153728 1/4 - 20 x 1-1/2” Stainless Steel Low Prole Cap Screw

4* 1 150867 Black Starboard Bae

5 1 153730 3/8 - 16 x 1-1/4” Stainless Steel Serrated Flange Bolt

6 1 153731 3/8” Stainless Steel Serrated Spring Lock Washer

7 2 153732 3/8” Stainless Steel 1” Diameter Flat Washer

8 1 153677 Top Bracket

9 1 151140 3/8 - 16 U-Nut

10 2 153735 #8 x 1/2” Stainless Steel Pan Head Screw

11 1 153707 Glove Box Latch

12 1 153676 Bottom Bracket

13 1 153734 1/4” Stainless Steel 5/8” Diameter Flat Washer

14 1 153733 #12 x 3/4” Stainless Steel Phillips Pan Head Screw

- 1 150249 Foam Strips (not shown)

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio MX300/1. The diagram below shows the recommended crossover settings for the MX300/1. For a detailed description of the

amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your

Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for

both channels of the amplier. JL Audio recommends using 12AWG speaker wire for subwoofers such as the XC-BCS12-25.

Continued on Next Page

Page 3 • JL Audio, Inc., 2016

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Page 4 • JL Audio, Inc., 2016 Continued on Next Page

STEP 8

Move the upper dash panel up out of the way

as shown.

STEP 7

Carefully unclip the upper dash panel.

STEP 6

Remove the handle from the vehicle.

STEP 5

Remove the retainer clip and pin from the

passenger handle.

STEP 4

Remove the indicated Torx bolt from under the

front cover, along with the one on the opposite

side.

STEP 3

Remove the front cover from the vehicle.

STEP 2

Remove the two indicated clips on the front

cover.

STEP 1

Empty the vehicle.

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Page 5 • JL Audio, Inc., 2016 Continued on Next Page

STEP 16

Carefully unclip the dash panel from around

the glove compartment, and remove panel

from the vehicle.

STEP 15

Carefully unclip the side of the dash panel.

STEP 14

Carefully unclip the top of the dash panel.

STEP 13

Remove the indicated Torx bolt from the dash

panel, along with the one on the opposite side.

STEP 12

Pictured are the dash light and USB grommet

removed from the dash panel.

STEP 11

Remove the indicated grommet for the USB

connector from the dash panel, if equipped.

STEP 10

Remove the indicated dash light from the dash

panel.

STEP 9

Remove the indicated screw from the dash

panel bracket.

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Page 5 • JL Audio, Inc., 2016 Continued on Next Page

STEP 24

Thread a 1/4 - 20 x 1” Serrated Flange Bolt

through the hole in the short side of the

Bottom Bracket, into the threaded insert on

the bottom of the enclosure, and hand tighten.

Secure the Bottom Bracket to the factory

mounting point in the vehicle using a #12 x 3/4”

Phillips Pan Head Screw and 1/4” Flat Washer as

shown, and hand tighten.

STEP 23

Secure the Side Bracket to the frame using the

factory bolt removed in Step 20, and hand

tighten. Thread a 1/4 - 20 x 1” Serrated Flange

Bolt through the hole in the Side Bracket, into

the threaded insert in the side of the enclosure,

and hand tighten.

STEP 22

Connect speaker cable to the barrier strip

on the side of the enclosure, and lift the

Stealthbox® into position as shown. Thread

a pair of 1/4 - 20 x 1” Serrated Flange Bolts

through the holes in the Top Bracket, into the

threaded inserts in the top of the

enclosure, and hand tighten.

STEP 21

Secure the Top Bracket to the frame as shown

using a 3/8 - 16 x 1-1/4” Serrated Flange Bolt,

3/8” Serrated Spring Lock Washer, and a 3/8”

Flat Washer above the bracket, and a 3/8” Flat

Washer and 3/8 - 16 U-Nut below the frame,

and hand tighten.

STEP 20

Remove the indicated bolt on the factory

bracket, and remove the bracket. This bracket

will not be reinstalled.

STEP 19

Pictured is the vehicle with the dash panel and

glove compartment removed.

STEP 18

Remove the two indicated bolts from the top

of the glove compartment, and remove the

glove compartment from the vehicle.

STEP 17

Open the glove compartment, unclip the door,

and remove the door from the vehicle.

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Page 5 • JL Audio, Inc., 2016 Continued on Next Page

STEP 32

Secure the replacement Glove Box Latch

bracket to the back of the glove compartment

as shown using the factory bolt removed in the

previous step.

STEP 31

Remove the factory bolt holding the latch

bracket to the back of the glove compartment

door, and remove the bracket.

STEP 30

Secure the glove compartment door latch to

the enclosure using the included #8 x 1/2” Pan

Head Screws.

STEP 29

Remove the two factory screws holding the

glove compartment door latch to the glove

compartment, and remove the latch. These

factory screws will not be reused.

STEP 28

Reinstall the dash light and USB connector, if

equipped, to the dash panel. Route the

speaker cable as necessary.

STEP 27

Secure the Side Bracket to the dash panel using

the factory screw removed in Step 9.

STEP 26

Reinstall the dash panel.

STEP 25

Check the Stealthbox® alignment using the

dash panel, make adjustments as necessary,

and fully tighten all mounting hardware.

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

Page 6 • JL Audio, Inc., 2016

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

SB-POL-RZG2/10TW3 INSTR_SKU# 011446

STEP 34

Reinstall the upper dash panel.

STEP 33

Reinstall the glove compartment door.

STEP 36

Reinstall the front cover.

Note: For optimum performance, we

recommend applying the included Foam Strips

(or sound damping material) to surrounding

plastic panels to reduce unwanted vibrations.

STEP 35

Reinstall the passenger handle.

MID/HIGH FREQUENCY DRIVER FITMENT

VeX™ Enclosed Speaker Systems are ideal for powersports and o-road vehicle applications. Each

weatherproof pod can be mounted to a roll cage precisely aimed for optimum sound. Mounting

xtures are available to t a variety of roll cage diameters.

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc.,. “Ahead of the