Johannus STUDIO I User manual

USER MANUAL
JOHANNUS STUDIO I AND II
Handleiding_Studio_Final01.fm Page 1 Tuesday, April 19, 2005 10:14 AM

2
/i
Manufacturer Johannus Orgelbouw b.v.
Address Keplerlaan 2
6716 BS EDE
Country The Netherlands
Telephone [phone]
Fax [phone]
E-mail [email protected]
Website www.johannus.com
Version 1.0
Date February 2005
© 2005, Johannus Orgelbouw b.v.
All rights reserved. Nothing in this publication may be reproduced, stored
in a data file or made public in any form or in any way either electronically,
mechanically by way of photocopying, recording or in any other way
without the prior written permission of Johannus Orgelbouw b.v.
Handleiding_Studio_Final01.fm Page 2 Tuesday, April 19, 2005 10:14 AM

3
TABLE OF CONTENTS
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Symbols on the organ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Symbols in the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Placement and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Connecting and switching on the accessories (option) . . . . . . . . . . . . . . . . . . 7
2.4 Transport and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 DESCRIPTION OF THE ORGAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Overview of the main components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Overview of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Volume adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3 Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.4 Couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.5 Changing the registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.6 Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.6.1 Tune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6.2 Transposer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.7 Stop memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7.1 Fixed memory location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.7.2 Capture memory location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.8 Factory intonation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 MAINTENANCE, PROBLEMS AND WARRANTY . . . . . . . . . . . . . . . . . . 16
5.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1.1 Cabinet maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1.2 Maintenance of the manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2.1 Repositioning the pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Handleiding_Studio_Final01.fm Page 3 Tuesday, April 19, 2005 10:14 AM

4
Handleiding_Studio_Final01.fm Page 4 Tuesday, April 19, 2005 10:14 AM

5
1SAFETY
1.1 Safety precautions
1.2 Symbols on the organ
1.3 Symbols in the manual
Place the organ on a horizontal, stable surface.
Connect the organ to an electrical outlet with an earth
connection.
Turn off the organ when it is not in use.
Do not place the organ in a damp area.
Do not expose the organ to liquids.
Follow the instructions and precautionary measures in this user
manual.
Keep this user manual with the organ.
The organ may only be opened by a technician authorised by
Johannus Orgelbouw b.v. The organ contains static-sensitive
components. The warranty is void if the organ is opened by a
non-authorised person.
Warning
Warning for electric shock
Warning for static-sensitive components
Warning or important information
Note
Handleiding_Studio_Final01.fm Page 5 Tuesday, April 19, 2005 10:14 AM

6
2INSTALLATION
2.1 Placement and connection
1. Place the organ on a stable, horizontal surface.
2. Lean the organ slightly backward.
3. Slide the pedal (A) against the pedalboard (B).
4. Set the organ upright.
5. Put the music desk (C) in the groove on the cover of the organ.
6. Place the organ bench over the pedalboard.
7. Make sure the voltage of the organ matches the voltage of the mains.
See the serial plate (D).
8. Connect the organ to an electrical outlet with an earth connection.
C
B
A
D
Handleiding_Studio_Final01.fm Page 6 Tuesday, April 19, 2005 10:14 AM

7
2.2 Switching on
1. Switch on the organ with the on/off button at the right, next to the
manuals.
The lamps of the on/off, 0 and SET buttons go on.
2. Wait several seconds. Starting the control functions and the settings
takes a little time.
2.3 Connecting and switching on the accessories (option)
You can connect accessories (for example, a MIDI-device) to the organ.
1. Switch off the organ and the accessory.
2. Connect the accessory to the organ. The connections are on the rear of
the organ.
3. Switch on the accessory.
4. Switch on the organ.
2.4 Transport and storage
Pay attention to the following during transport and storage:
Remove the music desk and the pedalboard from the organ.
Relative humidity within the storage area: 10 to 90%.
Follow the instructions provided in the documentation for the
accessory.
Handleiding_Studio_Final01.fm Page 7 Tuesday, April 19, 2005 10:14 AM

8
3DESCRIPTION OF THE ORGAN
3.1 Overview of the main components
/i
A Stops E Pedalboard
B Music desk F Expression pedal
C Manuals G Loudspeakers
D Organ bench
BA
DE
C
FG
Handleiding_Studio_Final01.fm Page 8 Tuesday, April 19, 2005 10:14 AM

9
3.2 Overview of controls
/i
A Acoustic volume J 0-button or reset button
B Accessories K Manual Bass
C Pedal stops L Transposer
D Great stops M TUNE
E Swell stops N SET
F Volume O Manual swell
G Headphone jack P Hand registration
H Memory locations Q On/off
I Capture memory banks
SETSET
PPMFMF FFFF M1M1 M2M2 M3M3 00MBMB TRANS TUNE
SETSET
PP MFMF FFFF M1M1 M2M2 M3M3 00 MBMB
TRANS
TUNE
AAN
AKOESTIEK
3DSURROUND
UIT
VOLUME
EA B C D F
P QNMLKIHG J O
Handleiding_Studio_Final01.fm Page 9 Tuesday, April 19, 2005 10:14 AM

10
4OPERATION
4.1 Volume adjustment
You can set various volume adjustments:
Volume control: Adjusts the volume of the complete organ.
Expression pedal: Adjusts the volume of the swell, independent of the
volume of the complete organ.
Acoustic volume: Activates and adjusts the length of the spatial
reproduction.
4.2 Headphones
1. Use headphones with an impedance of 30 Ωor higher (see headphone
specifications).
2. Connect the headphones to the headphone jack on the organ. The
internal speakers will switch off automatically.
4.3 Stops
The stops are activated via rocker switches or the stop memory. See § 4.7.
The lamp in the rocker-switch goes on when the associated stop is active.
The stops are divided into four groups:
Pedal stops: A stop group for selecting the stops controlled by the
pedalboard.
Great stops: A stop group for selecting the stops controlled by the great
organ.
Swell stops: A stop group for selecting the stops controlled by the swell
organ.
Accessories:
-Manual and pedal couplers: See § 4.4.
-Tremulants: Activating an undulating organ sound.
-Chorus: Tunes the various stops with respect to each other.
-Intonation 2: Activates the baroque intonation. Normally the
romantic intonation is active.
Handleiding_Studio_Final01.fm Page 10 Tuesday, April 19, 2005 10:14 AM

11
4.4 Couplers
Manual coupler: Couples all of the keys for the swell stops to the great
stops. Use the accessory Swell organ - Great organ to activate the
Manual coupler.
Pedal coupler: Couples all of the keys for the great stops or the swell
stops to the pedal. Use the accessory Great organ - Pedal or Swell organ
- Pedal to activate the pedal.
Manual Bass (MB): Couples one note from the great stops to the pedal.
Only the lowest note that is played on the great stops is coupled to the
pedal. Activate the manual bass with the MB button.
4.5 Changing the registration
The 0-button cancels registration in two ways:
A short press on the 0-button: Only the last change is cancelled.
A long press on the 0-button: All stops are cancelled. The accessories
Chorus and Intonation 2 are unaffected.
4.6 Pitch
The standard pitch is: A = 440 Hz. You can change the pitch with the TUNE
button or the TRANS button in combination with the buttons P, MF, FF, M1,
M2, M3 and 0. The TUNE button is for the fine adjustment of the pitch. The
TRANS button is for shifting the pitch by half-tone increments. The table
below provides an overview of the pitch change as a result of various button
combinations:
/i
PMF FF M1 M2 M3 0
Tune -3 Hz -2 Hz -1Hz 440 Hz +1Hz +2 Hz +3 Hz
Trans. -1½
tone
-1
tone
-½
tone
0+½
tone
+1
tone
+1½
tone
Handleiding_Studio_Final01.fm Page 11 Tuesday, April 19, 2005 10:14 AM

12
4.6.1 Tune
Checking the pitch
1. Press the TUNE button. The lighted button (P through 0) indicates the
pitch.
Changing the pitch
1. Press the TUNE button.
2. Press the button (P through 0) for the desired pitch shift.
3. Wait until the lights in the TUNE button and the P through 0 buttons go
out.
Programming the pitch
1. Press the TUNE button.
2. Press the button (P through 0) for the desired pitch shift.
3. Press the SET button.
4. Wait until the lights in the TUNE button and the P through 0 buttons go
out.
4.6.2 Transposer
Checking the pitch
1. Press the SET button. The lighted button (P through 0) indicates the
pitch.
The light in the TUNE button must remain lit while the pitch
programming is changed.
The pitch shift is not stored in memory. When the organ is switched
on again, the most recently programmed pitch will be active.
The pitch shift is stored in memory. When the organ is switched on
again, the programmed pitch will be active.
The light in the TRANS button must remain lit while the pitch
programming is changed.
Handleiding_Studio_Final01.fm Page 12 Tuesday, April 19, 2005 10:14 AM

13
Changing the pitch
1. Press the TRANS button.
2. Press the button (P through 0) for the desired pitch shift.
3. Wait until the lights in the TRANS button and the P through 0 buttons go
out.
Programming the pitch
1. Press the TRANS button.
2. Press the button (P through 0) for the desired pitch shift.
3. Press the SET button.
4. Wait until the lights in the TRANS button and the P through 0 buttons go
out.
4.7 Stop memory
Through use of the stop memory, a regisration can be made active with just
one button. Only the accessories Chorus and Intonation 2 cannot by
programmed in the stop memory.
The stop memory consists of two types of memory locations:
Fixed memory locations: Available via the buttons P, MF and FF. The
three fixed memory locations have factory settings (presets) appropriate
for the soft Piano (P), the moderately loud Mezzo Forte (MF) and the
very loud Fortissimo (FF). See § 4.7.1.
Capture memory locations: Available via the combination of the capture
memory banks M1, M2 and M3 with the buttons P, MF and FF. The nine
capture memory locations are not pre-programmed and can be
programmed by the musician. See § 4.7.2.
4.7.1 Fixed memory location
Calling up a fixed memory location
1. Push in the fixed memory location button (P through FF). The active
stops light up.
The pitch shift is not stored in memory. When the organ is switched
on again, the most recently programmed pitch will be active.
The pitch shift is stored in memory. When the organ is switched on
again, the programmed pitch will be active.
Handleiding_Studio_Final01.fm Page 13 Tuesday, April 19, 2005 10:14 AM

14
Programming a fixed memory location
1. Select the desired stops.
2. Push in the SET button. Hold in the button.
3. Push in the desired fixed memory location button (P through FF).
4. Release the fixed memory location button (P through FF).
5. Release the SET button.
Restoring the factory settings
1. Switch off the organ.
2. Push in the FF and M1 buttons. Hold in the buttons.
3. Switch on the organ.
4. Wait until the lights in the 0 button and SET button are lit.
5. Release the FF and M1 buttons.
4.7.2 Capture memory location
Calling up a capture memory location
1. Push in the desired capture memory bank (M1 through M3).
2. Press the desired memory location (P through FF). The active stops light
up.
Programming a capture memory location
1. Select the desired stops.
2. Press the desired capture memory bank (M1 through M3).
3. Push in the SET button. Hold in the button.
4. Push in the desired memory location (P through FF).
5. Release the memory location button (P through FF).
6. Release the SET button.
The current setting of the fixed memory location will be lost.
The settings you have made in the fixed memory locations will be
lost.
The current setting of the capture memory location will be lost.
Handleiding_Studio_Final01.fm Page 14 Tuesday, April 19, 2005 10:14 AM

15
Clearing the capture memory locations
1. Switch off the organ.
2. Push in the MF and M2 buttons. Hold in the buttons.
3. Switch on the organ.
4. Wait until the lights in the 0 button and SET button are lit.
5. Release the MF and M2 buttons.
4.8 Factory intonation
Saving the intonation settings (option)
1. Connect a PC to the organ. Use the MIDI connection. See § 2.3.
2. Save the intonation settings on the PC using the intonation program from
Johannus.
Restoring the factory intonation
1. Switch off the organ.
2. Push in the P and M3 buttons. Hold in the buttons.
3. Switch on the organ.
4. Wait until the lights in the 0 button and SET button are lit.
5. Release the P and M3 buttons.
The settings you have made in the capture memory locations will
be lost.
The current intonation settings will be lost if the settings are not
saved on a PC.
Handleiding_Studio_Final01.fm Page 15 Tuesday, April 19, 2005 10:14 AM

16
5MAINTENANCE, PROBLEMS AND WARRANTY
5.1 Maintenance
Overview
5.1.1 Cabinet maintenance
The cabinet is made of solid wood and wood veneer.
1. Clean the cabinet with a damp cloth.
2. Rub the cabinet dry with a lint-free cloth.
5.1.2 Maintenance of the manuals
The manuals are plastic.
1. Clean the manuals with a damp cloth.
2. Rub the manuals dry with a lint-free cloth.
3. Remove any scratches with car polish.
Component Maintenance Frequency
Cabinet Cleaning. See § 5.1.1. As required
Manuals Cleaning and removing scratches.
See § 5.1.2.
As required
Do not use furniture polish or teak oil to clean the organ
cabinet.
Direct sublight may discolour the organ cabinet.
Do not use aggressive cleaning agents such as paint thinner or
acetone to remove dirt.
Handleiding_Studio_Final01.fm Page 16 Tuesday, April 19, 2005 10:14 AM

17
5.2 Problems
Overview
5.2.1 Repositioning the pedal
1. Make sure the organ is placed on a stable, horizontal surface.
2. Lean the organ slightly backward.
3. Slide the pedal against the pedalboard.
4. Set the organ upright.
5. Make sure the pedalboard works properly.
6. Contact your dealer if the pedalboard does not work properly.
5.3 Warranty
The conditions are specified in the warranty certificate. The warranty is void
if changes or repairs are made to the organ by persons or organisations that
are not authorised by Johannus Orgelbouw b.v.
Problem Cause Solution
Pedal does
not work
properly
The pedal magnet is making poor
contact with the magnetic switch at
the rear of the pedalboard.
Reposition the
pedalboard. See §
5.2.1.
Organ
functions do
not work
properly
The organ is not earthed. Connect the organ
to an electrical
outlet with an earth
connection.
Handleiding_Studio_Final01.fm Page 17 Tuesday, April 19, 2005 10:14 AM

18
Handleiding_Studio_Final01.fm Page 18 Tuesday, April 19, 2005 10:14 AM

19
INDEX
Numerics
0-button . . . . . . . . . . . . . . . . . . . . . 11
A
Accessories . . . . . . . . . . . . . . . . . . . 7
C
Capture memory location . . . . . . 13, 14
calling up . . . . . . . . . . . . . . . . . 14
factory setting . . . . . . . . . . . . . . 15
programming . . . . . . . . . . . . . . . 14
Connection . . . . . . . . . . . . . . . . . . . . 6
Controls . . . . . . . . . . . . . . . . . . . . . . 9
Couplers . . . . . . . . . . . . . . . . . . . . 11
E
Expression pedal . . . . . . . . . . . . 8, 10
F
Factory intonation . . . . . . . . . . . . . . 15
Factory setting
capture memory location . . . . . . . 15
fixed memory location . . . . . . . . . 14
intonation . . . . . . . . . . . . . . . . . 15
FF . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fixed memory location . . . . . . . . . . . 13
calling up . . . . . . . . . . . . . . . . . 13
factory setting . . . . . . . . . . . . . . 14
programming . . . . . . . . . . . . . . . 14
Fixed memory locations . . . . . . . . . . 13
H
Headphones . . . . . . . . . . . . . . . . . . 10
M
M1, M2 and M3 . . . . . . . . . . . . . . . . . 9
Main components . . . . . . . . . . . . . . . 8
Maintenance . . . . . . . . . . . . . . . . . . 16
Manual Bass . . . . . . . . . . . . . . . . . . 11
MF . . . . . . . . . . . . . . . . . . . . . . . . . . 9
P
P. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pitch . . . . . . . . . . . . . . . . . . . . . . . 11
changing . . . . . . . . . . . . . . . 12, 13
checking . . . . . . . . . . . . . . . . . . 12
programming . . . . . . . . . . . . 12, 13
Placement . . . . . . . . . . . . . . . . . . . . 6
Problems . . . . . . . . . . . . . . . . . . . . 17
S
SET button . . . . . . . . . . . . . . . . . . . . 9
Stops . . . . . . . . . . . . . . . . . . . . . . . 10
Storage . . . . . . . . . . . . . . . . . . . . . . 7
Switching on . . . . . . . . . . . . . . . . . . . 7
T
TRANS button . . . . . . . . . . . . . . . . . 12
Transport . . . . . . . . . . . . . . . . . . . . . 7
TUNE button . . . . . . . . . . . . . . . . . . 12
V
Volume adjustment . . . . . . . . . . . . . 10
Handleiding_Studio_Final01.fm Page 19 Tuesday, April 19, 2005 10:14 AM

20
Handleiding_Studio_Final01.fm Page 20 Tuesday, April 19, 2005 10:14 AM