Johannus Ecclesia Choir User manual

Choir / T-150

User Manual Ecclesia Choir / Ecclesia T-150
2
Manufacturer Johannus Orgelbouw b.v.
Address Keplerlaan 2
6716 BS EDE
Country The Netherlands
Telephone [phone]
Fax [phone]
E-mail [email protected]m
Website www.johannus.com
Version 1.0
Date September 2012
© 2012 Johannus Orgelbouw b.v.
All rights reserved. Nothing in this publication may be reproduced, stored in a
data file or made public in any form or in any way either electronically,
mechanically by way of photocopying, recording or in any other way without the
prior written permission of Johannus Orgelbouw b.v.

User Manual Ecclesia Choir / Ecclesia T-150
3
CONTENTS
1SAFETY........................................................................................... 5
1.1 Safety instructions ...................................................................................... 5
1.2 Symbols on the organ ................................................................................. 5
1.3 Symbols in this manual............................................................................... 5
1.4 Transport and storage ................................................................................ 5
2INSTALLATION ............................................................................... 6
2.1 Installation and connection ........................................................................ 6
2.1.1 Installation organ .........................................................................................6
2.1.2 Installation music desk .................................................................................7
2.2 Opening and closing roll cover ................................................................... 7
2.3 Switch on .................................................................................................... 7
3DESCRIPTION OF THE ORGAN......................................................... 8
3.1 Overview of the main components ............................................................ 8
3.2 Overview of controls................................................................................... 9
3.3 Connect and switch on the peripherals.................................................... 10
3.4 External connections ................................................................................ 10
4OPERATION ..................................................................................11
4.1 General Volume........................................................................................ 11
4.2 Expression pedals ..................................................................................... 11
4.3 Cathedral .................................................................................................. 11
4.4 Intonations................................................................................................ 11
4.5 Stops ......................................................................................................... 11
4.6 Couplers.................................................................................................... 12
4.7 Accessories ............................................................................................... 12
4.8 Capture memory....................................................................................... 13
4.8.1 Pre-programmed memory locations ..........................................................13
4.8.2 Capture memory locations:........................................................................14
4.8.3 Memory lock ..............................................................................................14
4.9 Transposer ................................................................................................ 14
4.10 Crescendo pedal ....................................................................................... 15
4.11 Quick Access ............................................................................................. 15
4.11.1 Programming mode crescendo pedal ........................................................15
5JOHANNUS MENU.........................................................................16
5.1 Crescendo ................................................................................................. 16
5.2 Datadump ................................................................................................. 17
5.3 Display Contrast........................................................................................ 18
5.4 Expr. Pedals............................................................................................... 18
5.5 General Volume........................................................................................ 19
5.6 Keyboard Config ....................................................................................... 20
5.7 Key Volumes ............................................................................................. 21
5.8 MIDI Config ............................................................................................... 24
5.9 Reset Procedures...................................................................................... 25
5.10 Reverb Settings......................................................................................... 25
5.11 Startup Settings ........................................................................................ 26
5.12 Temperaments.......................................................................................... 27
5.13 Tuning ....................................................................................................... 29
5.14 Version...................................................................................................... 29
6MAINTENANCE, TROUBLESHOOTING AND WARRANTY..................30
6.1 Maintenance............................................................................................. 30
6.1.1 Maintenance of the cabinet .......................................................................30

User Manual Ecclesia Choir / Ecclesia T-150
4
6.1.2 Maintenance of the manuals .....................................................................30
6.2 Problems................................................................................................... 30
6.3 Warranty................................................................................................... 30
7MIDI IMPLEMENTATIONS..............................................................31
7.1 MIDI Implementation Chart...................................................................... 31
7.2 MIDI Specifications ................................................................................... 32

User Manual Ecclesia Choir / Ecclesia T-150
5
1SAFETY
1.1 Safety instructions
1.2 Symbols on the organ
Warning
Warning for electric shock
Warning for static-sensitive components
1.3 Symbols in this manual
Warning or important information
Note
1.4 Transport and storage
Pay attention to the following during transport and storage:
1. Remove the music desk and the pedal board from the organ.
2. Relative humidity within the storage area: 40 to 60%.
Position the organ on a stable, horizontal surface.
Connect the organ to a grounded power socket.
Turn off the organ when it is not in use.
Do not place the organ in a damp area.
Do not expose the organ to liquids.
Follow the instructions and precautionary measures in this user manual.
Keep this user manual with the organ.
The organ may only be opened by a technician authorised by Johannus
Orgelbouw b.v. The organ contains static-sensitive components. The warranty
is void if the organ is opened by a non-authorised person.

User Manual Ecclesia Choir / Ecclesia T-150
6
2INSTALLATION
2.1 Installation and connection
2.1.1 Installation organ
Installing loudspeakers (Ecclesia T-150):
The external loudspeakers have to be installed by an authorized Johannus
installer.
Installing console:
1. Position the organ on a stable, horizontal surface.
2. Install the music desk (A) on top of the organ, see § 2.1.2.
3. Lean the organ slightly backward.
4. Slide the pedal board (D) against the organ.
5. Set the organ upright.
6. Place the organ bench (C) over het pedal board.
7. Make sure the voltage of the organ matches the voltage of the main. See the
serial plate (B).
8. Connect the organ to a grounded power socket.
A
B
C
D

User Manual Ecclesia Choir / Ecclesia T-150
7
2.1.2 Installation music desk
Ecclesia Choir:
Put the Plexiglas music desk in the music desk holder on top of the organ. Attach
the music desk to the music desk holder with the supplied brass screws.
Please use a hand screw driver. The use of an electric screw driver is not
recommended.
Ecclesia T-150:
Put the wooden music desk in the music desk holder on top of the organ.
2.2 Opening and closing roll cover
The organ can be closed with a wooden roll cover that has a lock. The roll cover
lock is positioned behind the music desk.
Opening
- Put the key in the roll cover lock.
- Turn the key a quarter turn to the left. The lock now comes out.
- Slide the roll cover upwards.
Closing
- Slide the roll cover downwards.
- Press the roll cover lock in.
- Turn the key a quarter turn to the right.
2.3 Switch on
Switch on the organ with the on/off piston at
the right, next to the manuals. Wait several
seconds. Starting the control functions and the
settings will take some time.
The lamps of the 0 piston and the as standard
set functions light up. The settings appear on
the display.
Initializing...
Please wait
Mem: 1 Vol:25
Tr: 0/440 Cr:--
Never leave the key in the area that can be closed!
It is recommended to leave the key in the lock.

User Manual Ecclesia Choir / Ecclesia T-150
8
3DESCRIPTION OF THE ORGAN
3.1 Overview of the main components
ARoll cover lock (behind music desk)
B Music desk
CRoll cover
DOrgan bench
ESwell pedal
FCrescendo pedal
GPedal board
A
B
C
D
G
F
E

User Manual Ecclesia Choir / Ecclesia T-150
9
3.2 Overview of controls
A Pedal stops, § 4.5
B Great stops, § 4.5
C Roll cover lock, § 2.2
D Swell stops, § 4.5
E Display, § 5
F Memory lock, § 4.8.3
G Phones, § 3.4
H SET (programming capture), § 4.8.2
I KT: Keyboard Transfer, § 4.7
J Capture memory locations, § 4.8.2
K Pre-programmed memory locations, § 4.8.1
L RO: Reeds Off, § 4.7
M CH: Chorus, § 4.7
N MB: Manual Bass, § 4.6
OCF: Cantus Firmus, § 4.6 CF: Cantus Firmus, § 4.6
PCR: Crescendo, § 4.10 CF: Cantus Firmus, § 4.6
Q TRANS.: Transposer, § 4.9
R- and + pistons, § 5
S ENTER, § 5
T MENU, § 5
U 0: Recall / Reset, § 4.7
V Manual Great
W Manual Swell
X Power switch, § 2.3
Y Intonation styles, § 4.4
Z MIDI stops, § 5.8
AA S/S: All Swells to Swell, § 4.7
AB SEQ- en SEQ+ pistions, § 4.7

User Manual Ecclesia Choir / Ecclesia T-150
10
3.3 Connect and switch on the peripherals
You can connect accessories (for example, a MIDI device) to the organ.
1. Switch off the organ and the accessory.
2. Connect the accessory to the organ.
3. Switch on the accessory.
4. Switch on the organ
3.4 External connections
The external connections are on the left under the console.
MIDI IN: An input for receiving MIDI codes from other devices.
MIDI MOD: A programmable MIDI output for connecting a sound module or
expander, for example.
MIDI SEQ: A non-programmable MIDI output for connecting a Johannus
Sequencer+ or PC (with the optional Johannus Intonat program), for example.
AUX IN: A stereo audio input for playing the sound of an external device through
the amplifiers of the organ. For example, an expander connected to the organ
through the MIDI MOD can be played through the instrument's loudspeakers.
AUX OUT: A stereo audio output for connecting an external device (amplifier or
recording device, for example).
Phones:
The phones connection is at the left next to the manuals.
This connection for a (stereo) headphone is suited for a headphone with an
impedance of 30 Ω or more (see headphone specifications).
When the headphone is used, the loudspeakers of the organ are switched off
automatically.
Follow the instructions provided in the documentation for the accessory.

User Manual Ecclesia Choir / Ecclesia T-150
11
4OPERATION
4.1 General Volume
The general volume of the organ can be adjusted with use of the Johannus Menu.
See § 5.5 General Volume.
4.2 Expression pedals
The organ has two expression pedals. One is configured as a swell pedal for the
Swell, and one is configured as a crescendo pedal. With use of the Johannus
Menu, the function of the expression pedals can be changed, see § 5.4 Expr.
Pedals.
Using an expression pedal which is set as a swell pedal will next to the volume
also changes the timbre of the stops. By this the effect of the swell box shutters of
a pipe organ is simulated.
4.3 Cathedral
The organ is equipped with the Adaptive Surround Reverb ASR-12 system. This
effect provides a spatial reproduction of the organ sound.
With use of the Johannus Menu the following settings are to adjust per intonation
style: Reverb Program, Reverb Length, Reverb Volume and 3D Surround effect.
See § 5.10 Reverb Settings.
4.4 Intonations
The organ has 4 intonations: Romantic (ROM), Symphonic (SYM), Baroque (BAR)
and Historic (HIS).
Select an intonation style by pressing the ROM, SYM, BAR or HIS piston.
4.5 Stops
The stops are activated via stop switches, pre-programmed memory locations,
capture memory locations or the crescendo pedal.
The lamp in the stop switch lights when the associated stop is active.
The stops are divided into three groups:
Pedal: Activates the stops associated with the Pedal.
Great: Activates the stops associated with the Great.
Swell: Activates the stops associated with the Swell.

User Manual Ecclesia Choir / Ecclesia T-150
12
4.6 Couplers
Manual coupler:
SWELL - GREAT: Fully couples all keys of the Swell to the Great.
Pedal couplers:
GREAT - PEDAL: Fully couples all keys of the Great to the Pedal.
SWELL - PEDAL: Fully couples all keys of the Swell to the Pedal.
Manual Bass (MB):
Couples the Pedal monophonic to the Great. Only the lowest key that is played on
the Great is coupled from the Pedal to the Great.
If only the lowest key of a chord is released, the pedal key activated by the
Manual Bass function is dropped until a new lowest key is played.
Activate the Manual Bass with the MB piston.
Cantus Firmus (CF):
Cantus firmus: Latin for ‘fixed voice’ or in organs ‘solo voice’ or ‘melody coupler’.
Couples the Swell monophonic to the Great. Only the highest key that is played on
the Great is coupled from the Swell to the Great.
With use of a solo registration on the Swell in this way a solo is heard while
playing only on the Great.
If only the highest key of a chord is released, the key activated by the Cantus
Firmus function is dropped until a new highest key is played.
Activate the Cantus Firmus with the CF piston.
4.7 Accessories
KT: Keyboard Transfer
Keyboard Transfer is a function to switch the manuals of the Great and the Swell.
When Keyboard Transfer is active manual 1 is the Swell manual and manual 2 is
the Great manual.
Activate the Keyboard Transfer with the KT piston.
CH: Chorus
Chorus is a function for lightly detuning the organ stops to give it a broader and
livelier sound. Use the CH piston to activate the Chorus.
RO: Reeds Off
Reeds off is a function to switch off all reed stops simultaneously. As long as this
piston is pressed, no reed stops can be activated. When this function is switched
It is advisable not to use the Cantus Firmus in combination with the coupler
SWELL - GREAT because this overrules the solo function of the Cantus Firmus.
It is advisable not to use the Manual Bass while playing the pedal board to avoid
double bass tones.

User Manual Ecclesia Choir / Ecclesia T-150
13
off, the reed stops that were on are activated again. Use the RO piston to activate
the Reeds Off function.
S/S: All swells to swell
All Swells to Swell transforms the swell pedal for the Swell to a swell pedal for the
whole organ.
0: Recall / Reset function
The 0 piston cancels registration in two ways:
1. A short press on the 0 piston: Only the last change is cancelled.
2. A long press on the 0 piston: All registrations are cancelled.
SEQ- and SEQ+: Sequence - and +
Sequence is a function for sequential selecting capture memory locations.
1. Select a capture memory location to start (for example level 2, location 2).
2. Use the SEQ- or SEQ+ pistons to select the previous or next capture memory
location.
4.8 Capture memory
4.8.1 Pre-programmed memory locations
Pre-programmed memory locations are available by operating pistons PP to T and
PL. These seven memory locations have factory settings (presets) appropriate for
the quiet pianissimo to the loud tutti and the classic plenum.
Calling up a pre-programmed memory location:
Press a pre-programmed memory location (PP-T or PL). The active stops light up.
Programming a pre-programmed memory location:
1. Select the desired stops.
2. Press the SET piston. The piston lights up. Hold in the piston.
3. Press the desired pre-programmed memory location (PP-T or PL).
4. Release the SET piston.
If the SET piston does not light up when pressed, programming of a memory
location is locked. See § 4.8.3 Memory lock
Although it is possible to store any registration under a piston of a pre-
programmed memory location it is advisable to select a registration matching the
text of the piston.
The current setting of the pre-programmed memory location will be lost.
If no expression pedal is configured as a swell pedal for the Swell, the S/S piston
cannot be activated.

User Manual Ecclesia Choir / Ecclesia T-150
14
4.8.2 Capture memory locations:
Through use of the capture memory, a registration can be made active with just
one piston.
The capture memory consists of 250 levels.
These levels can be seen on the display
(Mem:…). Each level has eight memory
locations (pistons 1-8). The 2000 capture
memory locations are not pre-programmed and can be programmed by the
musician.
Programming a capture memory location:
1. Select the desired stops.
2. Use the - and + pistons to select a level (1-250) on the display.
3. Press the SET piston. The piston lights up. Hold in the piston.
4. Press the desired memory location (1-8).
5. Release the SET piston.
Calling up a capture memory location:
1. Use the - and + pistons to select the desired level (1-250) on the display.
2. Press the desired memory location (1-8). The active stops light up.
4.8.3 Memory lock
The memory can be secured through a key switch. By turning the key a quarter to
the right, the security of the memory is removed. In this position, the key can not
be taken out of the lock.
Turn the key a quarter to the left to avoid unwanted overwriting of the memory.
Optionally the key can be taken out of the lock.
4.9 Transposer
The Transposer function shifts the pitch by half-tone increments (from -8 to +8).
The transposer setting can be read on the display
(Tr: …).
1. Press the TRANS piston.
2. Use the - and + pistons to set the pitch.
Through use of the SEQ- and SEQ+ pistons previous or next memory locations can
be selected in steps of one. The lighted memory location piston and the memory
level shown in the display indicate the selected location.
If the SET piston does not light up when pressed, programming of a memory
location is locked. See § 4.8.3 Memory lock
The current setting of the capture memory location will be lost.
Mem: 1 Vol:25
Tr: 0/440 Cr:--
Mem: 1 Vol:25
Tr: 0/440 Cr:--

User Manual Ecclesia Choir / Ecclesia T-150
15
3. When the transposer change needs to be saved, press the ENTER piston in
the time the TRANS. piston is lit.
4.10 Crescendo pedal
The crescendo pedal can be used to activate 20 registrations step-by-step. These
registrations start with very quiet (pianissimo) to very loud (tutti).
The default registrations of the 20 steps can be changed. See § 5.1 Crescendo.
Activating the crescendo pedal
If the crescendo pedal is not activated it is
indicated on the displays with Cr:--.
Use the CR piston to activate the crescendo
pedal. The display indicates the actual step.
Crescendo pedal as additional swell pedal
The crescendo pedal can also be configured as a swell pedal. See § 5.4 Expr.
Pedals.
If the crescendo pedal is set as additional swell pedal, all functions of the
crescendo pedal are deactivated.
4.11 Quick Access
Quick Access is a function to quickly access certain function of the organ.
4.11.1 Programming mode crescendo pedal
Pressing the ENTER and CR piston simultaneously enters the programming mode
of the crescendo pedal. See § 5.1 Crescendo, sub 4 for next steps.
This function is not available if no expression pedal is set as crescendo pedal. See
§ 5.4 Expr. Pedals.
Mem: 1 Vol:25
Tr: 0/440 Cr:--
Mem: 1 Vol:25
Tr: 0/440 Cr: 0

User Manual Ecclesia Choir / Ecclesia T-150
16
5JOHANNUS MENU
In the Johannus Menu several functions of the organ can be set.
Press the MENU piston to activate the Johannus Menu on the display.
Navigating the menu is done with the - and + pistons.
Confirmation of a choice is done with the ENTER piston.
Cancel or step back in the menu is done with the MENU piston.
The Johannus Menu consists of the following functions:
Function
More information
Crescendo
§ 5.1
Datadump
§ 5.2
Display Contrast
§ 5.3
Expr. Pedals
§ 5.4
General Volume
§ 5.5
Keyboard Config
§ 5.6
Key Volumes
§ 5.7
MIDI Config
§ 5.8
Reset Procedures
§ 5.9
Reverb Settings
§ 5.10
Startup Settings
§ 5.11
Temperaments
§ 5.12
Tuning
§ 5.13
Version
§ 5.14
5.1 Crescendo
The crescendo pedal contains 20 pre-programmed registrations. These registrations start with
very quiet (pianissimo) to very loud (tutti). These pre-programmed registrations can be
changed.
1. Press the MENU piston.
2. Use the - and + pistons to select the Crescendo
function on the display.
3. Press the ENTER piston. The first step of the crescendo
pedal appears on the display.
4. Use the - and + pistons to select the step which has to
be changed (for example step 5).
5. Change the registration and press the ENTER piston to
save the new registration in the memory of the organ.
6. Repeat steps 4 and 5 if more crescendo pedal steps has
to be changed.
Step 0 of the crescendo pedal cannot be changed.
Johannus Menu:
Crescendo
Johannus Menu:
Crescendo
Crescendo
Cres. step: 0
Crescendo
Cres. step: 5

User Manual Ecclesia Choir / Ecclesia T-150
17
7. Press the MENU piston 3x to exit the Johannus Menu.
5.2 Datadump
The Datadump function sends several settings from the organ to a storage medium (the
Johannus Sequencer+, for example) through the MIDI SEQ output. See § 3.4 External
connections.
The settings to sent are: the content of all capture memory locations and all settings which can
be set via the Johannus Menu, except Key Volumes. Key Volumes settings is a part of the
intonation data. These data can be received with the optional Johannus Intonat software.
a. Sending data from the organ
1. Press the MENU piston.
2. Use the - and + pistons to select the Datadump
functions on the display.
3. Press the ENTER piston. The Press ENTER text
appears on the display.
4. Make sure the desired storage medium is properly
connected.
5. Press the ENTER piston. When data is being sent,
Sending data... appears on the display. Sending
data will take some time.
6. If the data dump is complete, the main menu appears
on the display.
7. Press the MENU piston to exit the Johannus Menu.
b. Uploading data to the organ
Mem: 1 Vol:25
Tr: 0/440 Cr: 0
Johannus Menu:
Datadump
Johannus Menu:
Crescendo
Datadump
Press ENTER
Datadump
Sending data...
Johannus Menu:
Datadump
Do not use the organ when the Sending data... text is on the display.
Mem: 1 Vol:25
Tr: 0/440 Cr:--
Receiving a data file has no relation to the Johannus Menu and can be done
on every moment the organ is switched on, except when playing a Demo
Song.
Make sure to upload only data files which are recorded from the
instrument concerned. Uploading a data file from another instrument may
jeopardize the functioning of your instrument.

User Manual Ecclesia Choir / Ecclesia T-150
18
1. Make sure the storage medium, the Johannus
Sequencer+ for example, with a previous recorded data
file is properly connected.
3. Start sending the data file on the sequencer. A message
that a data file is being received appears on the display
of the organ.
4. When the upload is completed the main screen of the
display appears automatically.
5.3 Display Contrast
The Display Contrast function adjusts the display contrast.
1. Press the MENU piston.
2. Use the - and + pistons to select the Display
Contrast function on the display.
3. Press the ENTER piston. The current contrast level
appears on the display.
4. Use the - and + pistons to select the desired contrast
level.
5. Press the ENTER piston to confirm and to return to the
main menu.
6. Press the MENU piston to exit the Johannus Menu.
5.4 Expr. Pedals
The organ is equipped with PEPC™ (Programmable Expression Pedal Configuration). This
function makes it possible to configure each expression pedal to one’s own discretion.
We distinguish two types of expression pedals:
Swell pedal: dynamics by increase or decrease of volume. In a pipe organ
this is achieved by closing or opening the swell shutters of a
swell box. See also § 4.2 Expression pedals.
Crescendo pedal: dynamics by increase or decrease the amount of stops. See
also § 4.10 Crescendo pedal.
Johannus Menu:
Display Contrast
Johannus Menu:
Crescendo
Display Contrast
Level: 9
Johannus Menu:
Display Contrast
Mem: 1 Vol:25
Tr: 0/440 Cr:--
Uploading stored
data
Mem: 1 Vol:25
Tr: 0/440 Cr:--

User Manual Ecclesia Choir / Ecclesia T-150
19
1. Press the MENU piston.
2. Use the - and + pistons to select the Expr. Pedals
function on the display.
3. Press the ENTER piston. The first expression pedal
appears on the display.
4. Use the - and + pistons to select the expression pedal
which has to be changed. Expression pedal 2, for
example.
5. Press the ENTER piston. The first possibility for the
expression pedal appears on the display. The
possibilities are:
- Gt/Pd: swell pedal for Great and Pedal
- Sw: swell pedal for Swell
- Cresc: crescendo pedal
6. Use the - and + pistons to select the desired possibility,
Sw for example.
7. Press the ENTER piston. The cursor jumps to the actual
setting.
8. Use the - and + to select the desired setting, No for
example.
9. Press the ENTER piston to confirm. The cursor jumps
back.
10. If necessary, repeat steps 6 to 9 to change other
possibilities of press the MENU piston to return to the
Expression Pedal menu.
11. If necessary, repeat steps 4 to 10 for another
expression pedal of press the MENU piston 2x to exit
the Johannus Menu.
5.5 General Volume
The General Volume function sets the general volume of the organ.
a. An expression pedal can be configured as a swell pedal for several
divisions at the same time.
b. A division can only be connected to one expression pedal at the same
time.
c. An expression pedal cannot be configured as a swell pedal and a
crescendo pedal at the same time.
Johannus Menu:
Expr. Pedals
Johannus Menu:
Crescendo
Expr. Pedals
Expr. Pedal 1
Expr. Pedal 2
> Gt/Pd: No
Expr. Pedals
Expr. Pedal 2
Expr. Pedal 2
> Sw : Yes
Expr. Pedal 2
Sw : >Yes
Expr. Pedal 2
> Sw : No
Expr. Pedals
Expr. Pedal 2
Mem: 1 Vol:25
Tr: 0/440 Cr:--
Expr. Pedal 2
Sw : >No

User Manual Ecclesia Choir / Ecclesia T-150
20
1. Press the MENU piston.
2. Use the - and + pistons to select the General
VOlume function on the display.
3. Press the ENTER piston. The actual setting appears on
the display.
4. Use the - and + pistons to select the desired volume.
5. Press the SET piston to program the selected volume
into memory and to return to the Johannus Menu.
6. Press the MENU piston to exit the Johannus Menu.
5.6 Keyboard Config
The Keyboard Config function sets the operation of the keys.
1. Press the MENU piston.
2. Use the - and + pistons to select the Keyboard
Config function on the display.
3. Press the ENTER piston. The actual setting of the first
manual appears on the display.
4. Use the - and + pistons to select the manual the setting
of which must be changed: Great, or Swell
5. Press the ENTER piston. The cursor moves to the
second line of the display.
6. Use the - and + pistons to select a setting for the
operation of the keys.
- Automatic: The manual has been set to High.
When activating a programmable MIDI stop or
optional solo- or orchestral voice, the manual will be
set to Velocity automatically.
- High: The keys respond when touched very lightly.
- Low: The keys respond when pressed further.
- Velocity: The keys are touch-sensitive.
7. Press the ENTER piston. The manual setting is now
saved in the memory and the cursor moves back to the
first line of the display.
8. Repeat steps 4 to 7 to change the setting of another
manual or press the MENU piston 2x to exit the
Johannus Menu.
Johannus Menu:
Keyboard Config
Johannus Menu:
Crescendo
>Great
Automatic
Great
>Automatic
Mem: 1 Vol:25
Tr: 0/440 Cr:--
>Great
Automatic
Johannus Menu:
Crescendo
Johannus Menu:
General Volume
General Volume
Level: 25
Johannus Menu:
General Volume
Mem: 1 Vol:25
Tr: 0/440 Cr:--