JOHN BLUE DRV Series User manual

DRV SERIES
GROUND DRIVES
PARTS AND
INSTRUCTIONAL MANUAL
DRV-3000 Shown
JOHN BLUE COMPANY
Printed in U.S.A. 12-M-44 Rev 03/20
DIVISION OF ADVANCED SYSTEMS TECHNOLOGY, INC.
165 Electronics Blvd, Huntsville, AL 35824
Telephone: [phone] • FAX: [phone]
Toll Free: 1-800-253-2583
www.johnblue.com

2
TABLE OF CONTENTS
Table of Contents ..…………………………………………………………………………………………………… 2
Safety Precautions .………………………………………………………………………………………….………. 2
Installation Instructions: DRV 3000 / 3100 / 3300 ….………………..……………………………………..…..… 3
Installation Diagram ..…………………………………………………………………………………..………….... 4
Installation Instructions: DRV 3200 ...…………………………………………………………....…………...…... 5
Parts Diagram ………………………………………….....….………………….…………………….……...…….. 6
Parts List ………………………………………….....….………………….…………………….……...…………… 7
Warranty .…………………………………………………………………………………………………....……….. 8
SAFETY PRECAUTIONS
•Equipment should be operated only by responsible people.
•A careful operator is the best insurance against an accident.
WARNING: USE OF THIS PRODUCT FOR ANY PURPOSES OTHER THAN ITS ORIGINAL INTENT, ABUSE
OF THE PRODUCT, AND/OR MODIFICATION TO THE ORIGINAL PRODUCT IS STRICTLY PROHIBITED BY
JOHN BLUE COMPANY. JOHN BLUE COMPANY RESERVES THE RIGHT TO DENY WARRANTY OR
LIABILITY CLAIMS IN ANY/ALL SITUATIONS INVOLVING MISUSE, ABUSE OR MODIFICATION.
THE ORIGINAL INTENT OF THIS PRODUCT DOES NOT INCLUDE USE WHERE THE MAXIMUM
ALLOWED SPEED, PRESSURE, OR TEMPERATURE IS EXCEEDED, AND IT DOES NOT INCLUDE
APPLICATIONS UTILIZING FLUIDS THAT ARE NOT COMPATIBLE WITH THE PRODUCT’S COMPONENT
MATERIALS. DO NOT USE THIS PRODUCT WITH FLAMMABLE OR COMBUSTIBLE FLUIDS SUCH AS
GASOLINE, KEROSENE, DIESEL, ETC…, AND DO NOT USE IN EXPLOSIVE ATMOSPHERES. FAILURE
TO FOLLOW THIS NOTICE MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE AND WILL
VOID THE PRODUCT WARRANTY. IF IN DOUBT ABOUT YOUR APPLICATION, CONTACT YOUR
STOCKING DEALER OR THE JOHN BLUE TECHNICAL STAFF AT 1-800-253-2583.
WARNING: THIS PRODUCT CAN EXPOSE YOU TO CERTAIN CHEMICALS, WHICH ARE KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE CANCER OR BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
FOR MORE INFORMATION GO TO: www.P65Warnings.ca.gov.

3
Installation Instructions: DRV-3000, 3100, 3300
*refer to diagram on next page
1) Attach the Universal Mount (G) to the toolbar using the correct set of U-Bolts.
2) Using the Jack-Shaft Carrier Assembly (B), attach the Arm-Weldment (C) to the
Universal Mount (G).
3) Attach Spring Assembly (-3300) or Gauge Adjustment (-3000, -3100) to the
Arm-Weldment (C) and the Universal Mount (G) using the two gauge pins and
cotter pins.
4) Attach the wheel to the Spindle assembly using the 9/16 lug bolts.
5) Making sure the Spindle Assembly is oriented correctly, attach it to the Arm-
Weldment (C).
6) Attach the Pump Mount (E) on top of the Universal Mount (G). Check to make
sure the mount is oriented correctly as shown in the picture below.
7) Mount each Idler Assembly (D) in the correct position for either a Push or Pull
type setup. Refer to page 4for a Pull-Type illustration and page 6 for a Push-
Type illustration.
8) Install the sprockets on the Jack-Shaft carrier (B). The 18T Sprocket (#21)
should be installed (with the hub facing outward) on the same side of the Jack-
Shaft carrier as the spindle sprocket. The 24T Sprocket (#23) should be
installed on the other side to align with the pump sprocket.
9) Mount both drive chains as shown in the diagram on page 4. Adjust the idlers
to take up slack in the drive chains.
**Note: The slot in the Pump Mount is
slightly closer to this side of the
Universal Mount – install as shown.
**Note: The Idler Assembly is attached to
the inside wall of the Pump Mount leg –
see step 7.

4
Installation Diagram: DRV-3000, 3100, 3300
A
B
DRV-3300
Spring Assembly
DRV 3000, 3100
Gauge Adjustment
E
G
D
D
C
F
**For item number descriptions
refer to Parts listing on page 7
** Note: Idler bracket positions are shown for Pull Type installation
Wheel Rotation
Direction of
Travel -
Pull Type
Install
List of major Assemblies and Parts
A) Spindle Assembly
B) Jack-Shaft Carrier Assembly
C) Arm-Weldment
D) Idler Assembly
E) Pump Mount
F) U-Bolts (Ordered Separately)
G) Universal Mount

5
Installation Instructions: DRV 3200 Planter Drive
#21a: 114932-01
Attach to
planter shaft
#54: U-bolts
sold separately
**See pages 6 and 7 for part numbers of shared components
#47a: 114934-01
#21b: 114936-91
Reverse idler
bracket if chain
rotation is opposite
direction shown

6
Parts Diagram: All Models
** Note: Idler bracket positions are shown for Push Type installation
Wheel Rotation
Direction
of Travel -
Push Type
Install

7
Parts List
Item Part # Description DRV-3000 Fixed Height
Drive
DRV-3100
Gage Wheel
Only
DRV-3200
Planter Mount
DRV-3300
Spring Load
Drive
1
92031
½-13 JAM NUT
2
1
2
2
92029
½-13 HEX NUT
2
1
2
3
93012
7/16 FLAT WASHER
6
3
6
4
A-401
IDLER SPOOL
2
1
2
5
A-512
FERRULE
2
1
2
6
115944-01
IDLER BRACKET
2
1
2
7
90699
½-13 X 3-1/4 BOLT
2
1
2
8
93018
¾ SAE FLAT WASHER
4
4
4
4
9
93028
¾ LOCK WASHER
4
4
4
4
10
92039
¾-10 HEX NUT
4
4
4
4
11
93011
3/8 FLAT WASHER
15
2
10
15
12
93024
3/8 LOCKWASHER
15
2
8
15
13
92024
3/8-16 HEX NUT
10
2
8
10
14
90860
3/8-16 X 1 BOLT
4
2
4
4
15
115938-91
PUMP MOUNT – PISTON
1
1
1
16
90653
3/8-16 X 1-1/4 BOLT
4
4
4
17
115916-01A
COLLAR
2
2
2
18
115915-01
RETAINING RING
2
2
2
19
L-1017
BEARING
2
2
2
20
115933-91
PIVOT PLATE TUBE
1
1
1
1
21
21a
21b
112661-01
114932-01
114936-91
SPROCKET – RC50-18T
SPROCKET – RC40-32T
SPLT. SPKT.- RC40-32T
1
1
1
1
22
L-1020
¼” STD. KEY
2
2
2
23
112794-01
SPROCKET – RC50-24T
1
1
1
24
115934-01
JACK SHAFT
1
1
1
25
90663
3/8-16 X 3-1/2 BOLT
2
2
26
115923-91
ARM – WELDMENT
1
1
1
27
93013
½ FLAT WASHER
4
4
4
28
92048
½-13 LOCK NUT
2
2
2
29
90700
½-13 X 3-1/2 BOLT
2
2
2
30
A-1363
WHEEL – 15” - 5 BOLT
1
1
1
31
115925-01
SPINDLE
1
1
1
32
M-330
GREASE SEAL
2
2
2
33
42500
CONE BEARING
1
1
1
34
42000
CUP BEARING
1
1
1
35
115900-02
HUB
1
1
1
36
M-327
OUTER CUP BEARING
1
1
1
37
M-326
OUTER CONE BEARING
1
1
1
38
115926-01
SPACER - SEAL
1
1
1
39
94017
COTTER PIN
1
1
1
40
115927-01
1-1/2 – 12 HEX NUT -
1
1
1
41
A-8148
FERRULE
5
5
42
A-1342-BP
SPROCKET – RC50 – 50T
1
1
43
91059
3/8-16 X 2-1/4 BOLT
5
5
44
S-5476
¼ X 1-1/4 ROLL PIN
1
1
1
45
115924-01
GAUGE PIN
1
1
46
A-6350
COTTER PIN
1
1
1
47
47a
115943-A
114934-01
RC50 CHAIN – 93 LINKS
RC40 CHAIN – 61 LINKS
1
1
1
48
115943-B
RC50 CHAIN – 105 LINKS
1
1
1
49
115946-91
GAUGE ADJUSTMENT
1
1
50
115911-91
SHOCK ASSEMBLY
1
51
115904-91
UNIVERSAL MOUNT
1
1
1
1
52
M-394
9/16-18 X 1-1/8 – LUG BOLT
5
5
5
53
115931-91
SPINDLE ASSEMBLY
1
1
1
54
115907-01A
115907-01B
115907-01C
115907-01D
U-BOLT 7 X 7 BAR (2 req’d)
U-BOLT 4 X 4 BAR (2 req’d)
U-BOLT 4 X 6 BAR (2 req’d)
U-BOLT 6 X 6 BAR (2 req’d)
NOT
INCLUDED NOT INCLUDED NOT INCLUDED NOT INCLUDED

8
YOUR LOCAL DEALER
JOHN BLUE COMPANY
Division of Advanced Systems Technology, Inc.
165 Electronics Blvd., Huntsville, AL 35824
Telephone: [phone] • Fax: [phone]
Toll Free 1-800-253-2583
www.johnblue.com
LIMITED WARRANTY
THIS WARRANTY IS IN LIEU OF ALL OTHER WRITTEN OR EXPRESS WARRANTIES AND REPRESENTATIONS.
ANY IMPLIED WARRANTIES INCLUDING MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE
ARE EXPRESSLY LIMITED TO THIS WRITTEN WARRANTY. JOHN BLUE COMPANY SHALL NOT BE LIABLE FOR
CONSEQUENTIAL DAMAGES.
Use of this product for any purpose other than its original intent, abuse of the product, and/or any modification to
the original product is strictly prohibited by the manufacturer, John Blue Company. Any modification to the product
should be approved by John Blue Company prior to use. John Blue Company will deny Warranty claims and liability
in any situation involving misuse, abuse or modification.
Each new machine or component manufactured by John Blue Company through original buyer is warranted by John
Blue Company to buyer and to any party or parties to whom buyer may resell, lease or lend the equipment to be free
from defects in material and workmanship under normal use and service. This obligation of John Blue Company under
this warranty is limited to the repair or replacement of defective parts or correction of improper workmanship of any parts
of such equipment which shall within one year from the date of John Blue’s original delivery thereof, be returned to John
Blue’s factory, transportation charges prepaid and which John Blue Company shall determine to its satisfaction upon
examination thereof to have been thus defective. When it is impractical to return the defective parts of such equipment
to John Blue’s factory, then John Blue shall have no liability for the labor cost involved in repairing or replacing any such
parts and shall be liable solely for supplying the material necessary to replace or repair the defective parts, provided that
prior thereto John Blue Company shall have determined to its satisfaction that any such parts are thus defective.
This warranty shall not apply to any equipment which shall have been repaired or altered outside John Blue’s factory in
any way so as to affect its durability, nor which has been subjected to misuse, abuse, negligence or accident, or operated
in any manner other than in accordance with operating instructions provided by John Blue Company. This warranty does
not extend to repairs made necessary by the use of inferior or unsuitable parts or accessories, or parts or accessories
not recommended by John Blue Company.
John Blue Company makes no warranties in respect to parts, accessories or components not manufactured by John
Blue Company, same ordinarily being warranted separately by their respective manufacturers.
DIVISION OF ADVANCED SYSTEMS TECHNOLOGY, INC. HUNTSVILLE, AL [phone]