Johnson Controls Unitary Products GCGD18 S41S3 Quick start guide

SPLIT-SYSTEM
AIR CONDITIONERS
13 SEER – R-410A – 1 PHASE
MODELS:
GCGD18 THRU 60
(1.5 THRU 5 NOMINAL TONS)
Due to continuous product improvement, specifications are
subject to change without notice.
Visit us on the web at www.york.com
Additional rating information can be found at
www.ahridirectory.org
WARRANTY
5-year limited parts warranty.
5-year limited compressor warranty.
®
TECHNICAL
GUIDE
TECHNICAL
GUIDE
556452-UTG-C-0611
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
DESCRIPTION
The 13 SEER Series unit is the outdoor part of a versatile cli-
mate system. It is designed with a matching indoor coil compo-
nent from Johnson Controls Unitary Products. Available for
typical applications this climate system is supported with acces-
sories and documents to serve specific functions.
FEATURES
•Quality Condenser Coils - The coil is constructed of alumi-
num microchannel tubing and enhanced aluminum fins for
increased efficiency.
•Protected Compressor - The compressor is internally pro-
tected against high pressure, temperature, and externally by
a factory installed high pressure switch. This is accomplished
by the simultaneous operation of high pressure relief valve
and a temperature sensor which protects the compressor if
undesirable operating conditions occur. A liquid line filter-
drier further protects the compressor.
•Durable Finish - The cabinet is made of pre-painted steel.
The pre-treated galvanized steel provides a better paint to
steel bond, which resists corrosion and rust creep. Special
primer formulas and matted-textured finish insure less fading
when exposed to sunlight.
•Lower Installed Cost - Installation time and costs are
reduced by easy power and control wiring connections.
Available in sweat connect models only. The unit contains
enough refrigerant for matching indoor coils and 15 feet of
interconnecting piping. The small base dimension means
less space is required on the ground or roof.
•Top Discharge - The warm air from the top mounted fan is
blown up away from the structure and any landscaping. This
allows compact location on multi-unit applications.
•Low Operating Sound Level - The upward air flow carries
the normal operating noise away from the living area. The
rigid top panel effectively isolates any motor sound. Isolator
mounted compressor and the rippled fins of the condenser
coil muffle the normal fan motor and compressor operating
sounds.
•Low Maintenance - Long life permanently lubricated motor-
bearings need no annual servicing.
•Easy Service Access - Fully exposed refrigerant connec-
tions, and a single panel covering the electrical controls
make for easy servicing of the unit.
•Secured Service Valves - Secured re-usable service valves
are provided on both the liquid and vapor sweat connections
for ease of evacuating and charging.
•U.L. and C.U.L. listed - approved for outdoor application.
•Agency Listed -U.L. and C.U.L. listed - approved for out-
door application. The unit is certified in accordance with the
Unitary Small Equipment certification program, which is
based on AHRI Standard 210/240.

556452-UTG-C-0611
2Johnson Controls Unitary Products
All dimensions are in inches. They are subject to change with-
out notice. Certified dimensions will be provided upon request.
Physical and Electrical Data
MODEL GCGD18
S41S3 GCGD24 S41S3 GCGD30 S41S3 GCGD36 S41S3 GCGD42 S41S3 GCGD48 S41S3 GCGD60 S41S3
Unit Supply Voltage 208-230V, 1 60Hz
Normal Voltage Range 1187 to 252
Minimum Circuit Ampacity 9.8 12.4 14.7 17.9 21.5 21.1 34.3
Max. Overcurrent Device Amps 215 20 25 30 35 35 60
Min. Overcurrent Device Amps 315 15 15 20 25 25 35
Compressor Type Rotary Recip Recip Recip Recip Recip Scroll
Compressor Amps Rated Load 7.4 9.3 10.6 13.1 16.0 15.7 26.2
Locked Rotor 40 43 54 74 84 84 150
Crankcase Heater No No No No No No No
Fan Motor Amps Rated Load 0.5 0.8 1.4 1.5 1.5 1.5 1.5
Fan Diameter Inches 17.5 17.5 17.5 22 22 22 24
Fan Motor Rated HP 1/12 1/8 1/4 1/4 1/4 1/4 1/4 Nominal RPM 1100 1075 1100 850 850 850 850
Nominal CFM 1400 1950 2050 3200 2950 2950 3600
Coil Face Area Sq. Ft. 9.60 9.60 9.60 13.07 14.16 14.16 18.68 Rows Deep 1 1 1 1 1 1 1
Fin / Inches 23 23 23 23 23 23 23
Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line Set OD (Field Installed) 5/8 3/4 3/4 3/4 7/8 7/8 7/8
Unit Charge (Lbs. - Oz.) 43 - 3 3 - 13 3 - 14 4 - 9 4 - 5 4 - 9 5 - 6
Charge Per Foot, Oz. 0.58 0.62 0.62 0.62 0.67 0.67 0.67
Operating Weight Lbs. 97 129 131 145 173 173 195
1.Rated in accordance with AHRI Standard 110, utilization range “A”.
2.Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection.
3.Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection.
4.The Unit Charge is correct for the outdoor unit, matched indoor coil, and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet,
add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.
B
A
C
Unit
Model
Dimensions
(Inches) Refrigerant Connection Service Valve Size
A1
1.Including Fan Guard.
B C Liquid Vapor
18 28 23-1/2 23-1/2
3/8”
3/4”
24 28 23-1/2 23-1/2
30 28 23-1/2 23-1/2
36 28 29 29
42 30 29 29 7/8”48 30 29 29
60 32 33-5/8 33-5/8

556452-UTG-C-0611
Johnson Controls Unitary Products 3
System Charge for Various Matched Systems
Outdoor Unit GCGD18
S41S3 GCGD24 S41S3 GCGD30 S41S3 GCGD36 S41S3 GCGD42 S41S3 GCGD48 S41S3 GCGD60 S41S3
Required Orifice or TXV 1,2 .048/4F1 .055/4F1 .061/4F1 .065/4G1 .075/4G1 .073/4H1 .087/4J1
Factory Charge, lbs-oz 3 - 3 3 - 13 3 - 14 4 - 9 4 - 5 4 - 9 5 - 6
Indoor Coil3,4 Additional Charge, oz
AHP18 0––––––
AHP30 –40––––
AHP36 ––20–––
AHP42 –––00––
AHP60 –––––00
AHR18 0––––––
AHR24 –4–––––
AHR30 –––––––
AHR36 ––20–––
AHR42 –––82––
AHR48 –––––0–
AHR60 ––––––4
AHE18 0––––––
AHE24 –4–––––
AHE30 –40––––
AHE36 –420–––
AHE42 –––82––
AHE48 –––––0–
AHE60 ––––––4
AHX18 0––––––
AHX30 –40––––
AHX36 –420–––
AHX42 –––82––
AHX48 –––––0–
AHX60 ––––––4
AV*24 TXV+0––––––
AV*36 –420–––
AV*48 ––––TXV+20–
AV*60 ––––TXV+200
F4FP024 0––––––
F4FP036 –0–––––
F4FP040 ––0––––
F4FV060 –––––00
F5FP048 –––824–
F5FP060 –––––00
F6FP018 0––––––
F6FP030 –40––––
F6FP036 –40––––
F6FP042 –––82––
F6FP048 ––––TXV+20–
F6FP060 ––––––4
FC/MC/PC18 0––––––
FC/MC/PC32 –40––––
FC/MC/PC35 –40––––
FC/MC/PC36 –0–––––
FC/MC/PC37 –420–––
For Notes See Page 4.

556452-UTG-C-0611
4Johnson Controls Unitary Products
PROCEDURES:
1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator, and 15 feet of interconnecting
line tubing.
2. Verify the TXV and additional charge required for specific evaporator coil in the system using the above table.
3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in Physical and Electrical Data Table.
4. For orifice or TXV matches requiring additional charge, the refrigerant needs to be weighed in for specific coil match and lineset length.
5. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator
+ adder for line set.
FC/MC/PC43 –4200––
FC/MC/PC48 –––824–
FC/MC/PC60 –––––00
FC/MC62 ––––––4
FC64 ––––––11
UC18 0––––––
UC36 –0–––––
UC48 –––824–
UC60 –––––00
FOOTNOTES:
1.For applications requiring a TXV use 1TVM series kit.
2.Approved orifice shipped with outdoor unit.
3.Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224.
4.PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications.
System Charge for Various Matched Systems (Continued)
Outdoor Unit GCGD18
S41S3 GCGD24 S41S3 GCGD30 S41S3 GCGD36 S41S3 GCGD42 S41S3 GCGD48 S41S3 GCGD60 S41S3
Required Orifice or TXV 1,2 .048/4F1 .055/4F1 .061/4F1 .065/4G1 .075/4G1 .073/4H1 .087/4J1
Factory Charge, lbs-oz 3 - 3 3 - 13 3 - 14 4 - 9 4 - 5 4 - 9 5 - 6
Indoor Coil3,4 Additional Charge, oz
Models 12-48 require start kits for TXV matches.

556452-UTG-C-0611
Johnson Controls Unitary Products 5
COOLING CAPACITY - With Air Handler Coils
UNIT
MODEL
AIR HANDLER COIL
MODEL1
COOLING
MODEL W RATED
CFM NET MBH SEER EER
TOTAL SENS.
13 SEER AC WITH MV - VARIABLE SPEED
GCGD18S41S3 MV12B 17 FC/MC18B 600 17.5 13.3 14.00 12.50
GCGD24S41S3 MV12B 17 FC/MC36B 800 24.0 17.4 14.00 12.00 MV12B 17 FC/MC35B 800 24.0 17.4 14.00 12.00
MV12B 17 FC/MC43B 800 24.0 17.3 14.00 12.00
GCGD30S41S3
MV12B 17 FC/MC35B 1000 29.0 21.6 14.00 12.00
MV16C 21 FC/MC35C 1000 30.0 21.6 14.00 12.00
MV12B 17 FC/MC43B 1000 29.0 21.6 14.00 12.00
MV16C 21 FC/MC43C 1000 30.0 21.6 14.00 12.00
GCGD36S41S3
MV12B 17 FC/MC43B 1225 35.4 25.2 14.00 11.75
MV16C 21 FC/MC43C 1200 36.0 25.4 14.00 12.00
MV16C 21 FC/MC48C 1200 36.0 25.4 14.00 12.00
MV20D 24 FC/MC48D 1200 36.0 25.6 14.00 12.00
MV12D 24 FC/MC48D 1135 35.0 25.4 14.00 12.00
GCGD42S41S3 MV16C 21 FC/MC43C 1400 42.0 30.0 13.50 12.00 MV16C 21 FC/MC48C 1400 42.0 30.0 13.50 12.00
MV20D 24 FC/MC48D 1400 42.0 30.0 14.00 12.00
GCGD48S41S3
MV16C 21 FC/MC48C 1600 48.0 35.0 13.50 12.00
MV20D 24 FC/MC48D 1600 48.0 35.0 13.50 12.00
MV16C 21 FC/PC60C 1625 47.5 34.4 13.50 11.50
MV20D 24 FC/MC60D 1600 48.0 35.0 13.50 12.00
GCGD60S41S3 MV20D 24 FC/MC60D 1800 57.0 38.5 13.00 11.00 MV20D 24 FC/MC62D 1800 57.0 38.5 13.00 11.00
MV20D 24 FC64D 1855 57.0 39.0 13.75 11.50
13 SEER AC WITH MX - VARIABLE SPEED
GCGD18S41S3 MX12B 17 FC/MC18B 585 17.9 13.5 14.75 12.50
GCGD24S41S3 MX12B 17 FC/MC35B 815 24.8 17.4 15.00 12.50 MX12B 17 FC/MC36B 745 24.2 16.9 14.75 12.25
MX12B 17 FC/MC43B 735 24.6 17.1 14.75 12.50
GCGD30S41S3
MX12B 17 FC/MC35B 1085 30.0 22.6 14.25 12.00
MX16C 21 FC/MC35C 1035 30.0 22.2 14.75 12.50
MX12B 17 FC/MC43B 1095 30.4 23.0 14.50 12.25
MX16C 21 FC/MC43C 970 30.2 21.8 15.00 12.50
GCGD36S41S3
MX12B 17 FC/MC43B 1220 35.4 25.2 13.75 11.75
MX16C 21 FC/MC43C 1140 35.4 25.0 14.50 12.25
MX12D 24 FC/MC48D 1225 36.0 25.6 14.25 12.25
MX16C 21 FC/MC48C 1150 36.2 25.6 14.75 12.50
GCGD42S41S3 MX16C 21 FC/MC43C 1365 42.5 30.0 14.25 12.00 MX16C 21 FC/MC48C 1390 43.0 30.4 14.50 12.25
MX20D 24 FC/MC48D 1415 43.0 30.2 14.50 12.00
GCGD48S41S3
MX16C 21 FC/MC48C 1685 48.5 35.6 13.75 11.50
MX20D 24 FC/MC48D 1525 48.0 34.2 14.00 11.75
MX16C 21 FC/PC60C 1630 48.5 34.6 14.00 11.75
MX20D 24 FC/MC60D 1585 48.5 34.6 14.00 12.00
GCGD60S41S3 MX20D 24 FC/MC60D 1780 57.5 38.8 13.75 11.50 MX20D 24 FC/MC62D 1795 58.0 38.8 14.00 11.75
MX20D 24 FC64D 1795 58.5 39.8 14.50 12.00
For Notes See Page 7.

556452-UTG-C-0611
6Johnson Controls Unitary Products
13 SEER AC WITH AV / F*FV - VARIABLE SPEED
GCGD18S41S3 AV*24 17 – 610 18.0 13.5 14.50 12.00
GCGD24S41S3 AV*36 21 – 725 24.0 17.4 14.00 12.00
GCGD30S41S3 AV*36 21 – 960 30.0 21.8 14.50 12.00
GCGD36S41S3 AV*36 21 – 1190 35.0 25.2 14.00 12.00
GCGD42S41S3 AV*48 24 – 1385 42.0 29.8 14.00 12.00
AV*60 24 – 1360 42.0 29.8 14.00 12.00
GCGD48S41S3 AV*48 24 – 1625 48.0 35.0 13.50 12.00 AV*60 24 – 1560 48.0 35.0 13.50 12.00
F4FV060 24 – 1600 48.0 34.6 14.00 11.50
GCGD60S41S3 AV*60 24 – 1730 58.0 39.0 13.50 11.00
F4FV060 24 – 1780 57.0 38.5 13.50 11.00
13 SEER AC WITH AHE / AHP / AHR / AHX / F*FP
GCGD18S41S3
AHE18 17 – 610 17.9 13.8 14.75 12.25
AHP18 17 – 650 17.5 12.9 13.00 11.00
AHR18 17 – 665 17.8 13.8 13.00 11.00
AHX18 17 - 630 18.0 13.8 14.50 12.00
F4FP024 18 – 600 17.5 12.9 13.00 11.00
F6FP018 17 - 600 17.8 13.3 14.50 12.00
GCGD24S41S3
AHE24 17 – 795 24.4 17.4 14.50 12.00
AHE30 17 – 795 24.4 17.4 14.50 12.00
AHE36 21 – 855 25.2 18.5 15.00 12.50
AHP30 17 – 795 24.0 16.8 13.00 11.00
AHR24 17 – 740 23.8 16.5 13.00 11.00
AHX30 17 – 820 24.0 16.9 14.50 12.00
AHX36 21 – 815 24.0 16.9 14.50 12.00
F4FP036 21.5 – 855 24.0 16.7 13.00 11.00
F6FP030 17 – 850 24.0 16.8 14.00 11.80
F6FP036 21 – 855 24.0 17.0 14.00 12.00
GCGD30S41S3
AHE30 17 – 985 29.4 21.4 14.00 11.75
AHE36 21 – 1000 30.2 22.0 14.75 12.25
AHP30 17 – 1015 29.0 21.0 13.00 11.00
AHP36 21 – 1040 29.0 21.0 13.00 11.00
AHR30 17 – 1095 29.4 22.2 13.00 11.00
AHR36 21 – 1060 29.8 22.0 13.00 11.00
AHX30 17 – 1025 29.4 22.2 14.00 11.75
AHX36 21 – 1005 30.0 22.3 14.50 12.00
F4FP040 18 – 1050 29.0 21.0 13.00 11.00
F6FP030 17 – 1035 29.2 21.6 13.60 11.40
F6FP036 21 – 980 29.4 21.4 14.00 12.00
GCGD36S41S3
AHE36 21 – 1190 35.6 25.4 14.25 12.00
AHE42 21 – 1180 35.8 25.8 14.50 12.25
AHP36 21 – 1235 35.0 24.8 13.00 11.00
AHP42 21 – 1255 35.0 24.8 13.00 11.00
AHR36 21 – 1245 34.6 24.6 13.00 11.00
AHR42 21 – 1230 35.6 25.4 13.00 11.25
AHX36 21 – 1225 35.2 25.0 13.50 11.50
AHX42 21 – 1190 35.4 25.2 14.00 11.80
F5FP048 24 – 1235 35.0 24.8 13.00 11.00
F6FP042 21 – 1290 35.8 25.8 13.50 11.50
For Notes See Page 7.
COOLING CAPACITY - With Air Handler Coils (Continued)
UNIT
MODEL
AIR HANDLER COIL
MODEL1
COOLING
MODEL W RATED
CFM NET MBH SEER EER
TOTAL SENS.

556452-UTG-C-0611
Johnson Controls Unitary Products 7
— = Not applicable.
MA Modular Air Handlers use coil only ratings.
13 SEER AC WITH AHE / AHP / AHR / AHX / F*FP (Continued)
GCGD42S41S3
AHE42 21 – 1385 43.0 30.4 14.50 12.00
AHP42 21 – 1485 41.0 29.2 13.00 11.00
AHR42 21 – 1485 42.5 30.6 13.00 11.00
AHX42 21 – 1395 42.0 29.9 14.50 12.00
F5FP048 24 – 1455 41.0 29.2 13.00 11.00
F6FP042 21 – 1455 42.0 30.1 14.00 11.75
F6FP048 24 – 1380 41.5 29.4 13.50 11.70
GCGD48S41S3
AHE48 24 – 1600 47.0 34.6 13.75 11.50
AHP48 24 – 1675 48.0 34.4 13.00 11.00
AHP60 24 – 1600 48.0 35.0 13.50 11.00
AHR48 24 – 1610 48.0 34.6 13.00 11.00
AHX48 24 – 1660 48.0 35.4 13.50 11.50
F5FP048 24 – 1600 48.0 34.4 13.00 11.00
F5FP060 24 – 1600 48.0 34.4 13.00 11.00
F6FP048 24 – 1625 47.0 34.8 13.00 11.30
GCGD60S41S3
AHE60 24 – 1835 58.5 39.8 13.50 11.50
AHP60 24 – 1850 57.0 38.5 13.00 11.00
AHR60 24 – 1870 57.0 38.5 13.00 11.00
AHX60 24 – 1905 58.5 40.0 13.50 11.50
F5FP060 24 – 1900 57.0 38.5 13.00 11.00
F6FP060 24 – 1710 57.5 39.0 13.50 11.50
Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and AHRI Standards 210. Cooling MBH based on 80 °F
entering air temperature, 50% RH, and rated air flow.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at 95 °F outdoor ambient divided by the total electric power in watt-hours at those
conditions.
SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total
electric power input in watt-hours during the same period.
1.MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.
COOLING CAPACITY - With Air Handler Coils (Continued)
UNIT
MODEL
AIR HANDLER COIL
MODEL1
COOLING
MODEL W RATED
CFM NET MBH SEER EER
TOTAL SENS.

556452-UTG-C-0611
8Johnson Controls Unitary Products
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils
UNIT MODEL FURNACE** COIL
MODEL
COOLING
CFM RANGE
(Min.-max.) WRATED
CFM NET MBH SEER1EER
TOTAL SENS.
GCGD18S41S3 450 - 750 14,17 FC/MC/PC18 600 17.5 12.9 13.00 11.00
450 - 750 14,17 UC18 600 17.5 12.9 13.00 11.00
GCGD24S41S3
600 - 1000 14 FC/MC/PC32 800 24.0 16.7 13.00 11.00
600 - 1000 17,21 FC/MC/PC35 800 24.0 16.7 13.00 11.00
600 - 1000 14,17,21 FC/MC/PC36 800 24.0 16.7 13.00 11.00
600 - 1000 14 FC/MC/PC37 800 24.0 16.7 13.00 11.00
600 - 1000 17,21 FC/MC/PC43 800 24.0 16.7 13.00 11.00
600 - 1000 14,17,21 UC36 800 24.0 16.7 13.00 11.00
GCGD30S41S3
800 - 1200 14 FC/MC/PC32 1000 29.0 21.0 13.00 11.00
800 - 1200 17,21 FC/MC/PC35 1000 29.0 21.0 13.00 11.00
800 - 1200 14 FC/MC/PC37 1000 29.0 21.0 13.00 11.00
800 - 1200 17,21 FC/MC/PC43 1000 29.0 21.0 13.00 11.00
GCGD36S41S3
1000 - 1400 14 FC/MC/PC37 1200 35.0 24.8 13.00 11.00
1000 - 1400 17,21 FC/MC/PC43 1200 35.0 24.8 13.00 11.00
1000 - 1400 21,24 FC/MC/PC48 1200 35.0 24.8 13.00 11.00
1000 - 1400 21,24 UC48 1200 35.0 24.8 13.00 11.00
GCGD42S41S3 1200 - 1600 17,21 FC/MC/PC43 1400 42.0 29.2 13.00 11.00 1200 - 1600 21,24 FC/MC/PC48 1400 42.0 29.2 13.00 11.00
1200 - 1600 21,24 UC48 1400 42.0 29.2 13.00 11.00
GCGD48S41S3
1400 - 1800 21,24 FC/MC/PC48 1600 48.0 34.4 13.00 11.00
1400 - 1800 21,24 FC/MC/PC60 1600 48.0 34.4 13.00 11.00
1400 - 1800 21,24 UC48 1600 48.0 34.4 13.00 11.00
1400 - 1800 21,24 UC60 1600 48.0 34.4 13.00 11.00
GCGD60S41S3
1600 - 2000 21,24 FC/MC/PC60 1800 57.0 38.5 13.00 11.00
1600 - 2000 24 FC/MC62 1800 57.0 38.5 13.00 11.00
1600 - 2000 24 FC64 1800 57.0 39.0 13.50 11.25
1600 - 2000 21,24 UC60 1800 57.0 38.5 13.00 11.00
1.Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one.
** Refer to Quick Selection Chart for specific furnace match-up.

556452-UTG-C-0611
Johnson Controls Unitary Products 9
COOLING CAPACITY - With High Efficiency Motor Furnaces
MODELS FURNACE
MODEL COIL MODEL1WCOOLING
RATED
CFM Net MBH SEER EER
TOTAL SENS.
13 SEER HP WITH VARIABLE SPEED FURNACES2
GCGD18S41S3
T*(8,L)X*A12 FC/MC/PC18A 14 540 17.7 12.9 14.50 12.50
T*(8,L)X*B12 FC/MC/PC18B 17 580 18.0 13.4 14.50 12.50
T*9X*B12 FC/MC/PC18B 17 590 18.0 13.4 14.50 12.50
T*(8,L)X*A12 UC18A 14 590 18.0 13.4 14.50 12.00
T*(8,L)X*B12 UC18B 17 595 18.0 13.4 14.50 12.00
T*9X*B12 UC18B 17 590 18.0 13.4 14.50 12.00
(T*(8,L)C/T*8V)*A12 FC/MC/PC18A 14 620 17.5 12.7 14.50 12.50
(T*(8,L)C/T*8V)*B12 FC/MC/PC18B 17 580 17.5 12.6 14.50 12.00
(T*9C/T*9V)*B12 FC/MC/PC18B 17 610 17.5 12.8 14.50 12.50
(T*(8,L)C/T*8V)*A12 UC18A 14 620 17.5 12.7 14.50 12.00
(T*(8,L)C/T*8V)*B12 UC18B 17 580 17.5 12.5 14.50 12.00
(T*9C/T*9V)*B12 UC18B 17 610 17.5 12.6 14.50 12.50
GCGD24S41S3
T*(8,L)X*A12 FC/MC/PC32A 14 800 24.0 16.9 14.00 11.50
T*(8,L)X*B12 FC/MC/PC35B 17 850 24.0 17.0 14.00 12.00
T*9X*C16 FC/MC/PC35C 21 715 23.8 16.3 14.00 12.00
T*9X*C20 FC/MC/PC35C 21 825 24.0 17.0 14.00 12.00
T*(8,L)X*A12 FC/MC/PC36A 14 815 24.0 16.8 14.00 12.00
T*(8,L)X*B12 FC/MC/PC36B 17 835 24.0 16.8 14.00 12.00
T*9X*B12 FC/MC/PC36B 17 775 24.0 16.8 14.00 12.00
T*9X*C16 FC/MC/PC36C 21 770 24.0 16.8 14.00 12.00
T*9X*C20 FC/MC/PC36C 21 810 24.0 16.8 14.00 12.00
T*(8,L)X*A12 FC/MC/PC37A 14 840 24.0 17.0 14.00 12.00
T*(8,L)X*B12 FC/MC/PC43B 17 865 24.0 17.0 14.00 12.00
(T*(8,L)C/T*8V)*A12 FC/MC/PC32A 14 775 24.0 17.0 14.00 11.50
(T*(8,L)C/T*8V)*B12 FC/MC/PC35B 17 760 24.0 16.8 14.00 12.00
(T*9C/T*9V)*B12 FC/MC/PC35B 17 815 24.0 17.1 14.00 12.00
(T*(8,L)C/T*8V)*A12 FC/MC/PC36A 14 805 24.0 16.9 14.00 12.00
(T*(8,L)C/T*8V)*B12 FC/MC/PC36B 17 765 24.0 17.0 14.00 12.00
(T*9C/T*9V)*B12 FC/MC/PC36B 17 815 24.0 16.9 14.00 12.00
(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 14 805 24.0 17.0 14.00 12.00
(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 17 760 24.0 16.9 14.00 12.00
(T*9C/T*9V)*B12 FC/MC/PC43B 17 800 24.0 17.0 14.00 12.00
(T*(8,L)C/T*8V)*A12 UC36A 14 805 23.6 16.6 13.80 11.50
(T*(8,L)C/T*8V)*B12 UC36B 17 765 23.6 16.7 14.00 11.50
(T*9C/T*9V)*B12 UC36B 17 815 23.6 16.7 13.80 11.50
GCGD30S41S3
T*(8,L)X*A12 FC/MC/PC32A 14 970 29.2 21.4 13.20 11.00
T*(8,L)X*B12 FC/MC/PC35B 17 1120 30.0 22.8 14.00 11.50
T*(8,L)X*C16 FC/MC/PC35C 21 1105 30.0 22.8 14.00 12.00
T*(8,L)X*C20 FC/MC/PC35C 21 850 28.8 20.6 14.00 12.00
T*9X*B12 FC/MC/PC35B 17 1085 29.8 22.8 14.00 12.00
T*9X*C16 FC/MC/PC35C 21 1075 29.8 22.4 14.00 12.00
T*(8,L)X*A12 FC/MC/PC37A 14 1105 30.0 22.9 13.80 11.50
T*(8,L)X*B12 FC/MC/PC43B 17 1125 30.0 22.9 14.00 12.00
T*(8,L)X*C16 FC/MC/PC43C 21 710 28.2 19.3 14.00 12.00
T*(8,L)X*C20 FC/MC/PC43C 21 870 29.6 21.2 14.00 12.00
T*9X*B12 FC/MC/PC43B 17 1095 30.0 22.9 13.80 11.50
T*9X*C16 FC/MC/PC43C 21 1055 30.0 22.9 14.00 12.00
T*9X*C20 FC/MC/PC43C 21 720 28.2 19.3 14.00 12.00
For Notes See Page 12.

556452-UTG-C-0611
10 Johnson Controls Unitary Products
GCGD30S41S3
(T*(8,L)C/T*8V)*A12 FC/MC/PC32A 14 1045 29.2 21.8 13.20 11.00
(T*(8,L)C/T*8V)*B12 FC/MC/PC35B 17 995 29.6 21.4 14.00 11.50
(T*9C/T*9V)*B12 FC/MC/PC35B 17 1045 29.4 22.0 13.50 11.50
(T*(8,L)C/T*8V)*C16 FC/MC/PC35C 21 1025 29.6 22.0 14.00 12.00
(T*(8,L)C/T*8V)*C20 FC/MC/PC35C 21 1080 30.0 22.4 14.00 12.00
(T*9C/T*9V)*C16 FC/MC/PC35C 21 1005 29.6 22.0 14.00 12.00
(T*9C/T*9V)*C20 FC/MC/PC35C 21 985 29.6 22.0 14.00 12.00
(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 14 980 29.8 21.8 13.80 11.50
(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 17 990 30.0 22.0 14.00 12.00
(T*9C/T*9V)*B12 FC/MC/PC43B 17 1035 30.0 22.0 13.80 11.50
(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 21 990 30.0 22.1 14.00 12.00
(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 21 1000 30.0 22.1 14.00 12.00
(T*9C/T*9V)*C16 FC/MC/PC43C 21 1030 30.0 22.0 14.00 12.00
(T*9C/T*9V)*C20 FC/MC/PC43C 21 995 30.0 22.1 14.00 12.00
GCGD36S41S3
T*(8,L)X*A12 FC/MC/PC37A 14 1290 35.2 25.4 13.30 11.25
T*(8,L)X*B12 FC/MC/PC43B 17 1300 35.2 25.4 13.30 11.25
T*(8,L)X*C16 FC/MC/PC43C 21 1175 35.2 24.8 14.00 11.50
T*(8,L)X*C20 FC/MC/PC43C 21 1250 35.6 25.6 13.80 11.70
T*9X*B12 FC/MC/PC43B 17 1270 35.2 25.4 13.25 11.25
T*9X*C16 FC/MC/PC43C 21 1260 35.4 25.4 13.45 11.40
T*9X*C20 FC/MC/PC43C 21 1185 35.0 24.6 13.55 11.40
T*(8,L)X*C16 FC/MC/PC48C 21 1185 35.6 25.2 14.00 11.50
T*(8,L)X*C20 FC/MC/PC48C 21 1270 35.8 25.8 14.00 11.50
T*9X*C16 FC/MC/PC48C 21 1280 35.8 25.8 13.70 11.50
T*9X*C20 FC/MC/PC48C 21 1205 35.4 25.0 13.70 11.50
T*9X*D20 FC/MC/PC48D 24 1240 35.4 25.0 13.70 11.50
T*(8,L)X*C16 UC48C 21 1185 34.2 24.8 13.50 11.50
T*(8,L)X*C20 UC48C 21 1300 34.8 25.4 13.50 11.50
T*9X*C16 UC48C 21 1280 34.6 24.8 13.15 11.20
T*9X*C20 UC48C 21 1205 34.0 24.6 13.25 11.20
T*9X*D20 UC48D 24 1240 34.0 24.6 13.30 11.25
(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 14 980 33.8 23.0 13.50 11.00
(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 17 1210 35.2 25.2 13.50 11.00
(T*9C/T*9V)*B12 FC/MC/PC43B 17 1200 35.2 25.2 13.50 11.00
(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 21 1205 35.6 25.4 14.00 11.50
(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 21 1190 35.6 25.4 14.00 12.00
(T*9C/T*9V)*C16 FC/MC/PC43C 21 1240 35.4 25.2 13.50 11.50
(T*9C/T*9V)*C20 FC/MC/PC43C 21 1200 35.6 25.4 14.00 11.50
(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 21 1210 36.0 26.0 14.00 12.00
(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 21 1155 36.0 26.1 14.00 12.00
(T*9C/T*9V)*C16 FC/MC/PC48C 21 1195 36.0 26.0 14.00 11.50
(T*9C/T*9V)*C20 FC/MC/PC48C 21 1330 36.0 26.5 14.00 11.50
(T*9C/T*9V)*D20 FC/MC/PC48D 24 1240 36.0 26.2 14.00 12.00
(T*(8,L)C/T*8V)*C16 UC48C 21 1210 34.6 24.8 13.50 11.50
(T*(8,L)C/T*8V)*C20 UC48C 21 1155 34.8 24.8 14.00 11.50
(T*9C/T*9V)*C16 UC48C 21 1195 34.6 24.8 13.50 11.50
(T*9C/T*9V)*C20 UC48C 21 1305 35.0 25.6 13.30 11.00
(T*9C/T*9V)*D20 UC48D 24 1240 34.8 25.0 13.80 11.50
For Notes See Page 12.
COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)
MODELS FURNACE
MODEL COIL MODEL1WCOOLING
RATED
CFM Net MBH SEER EER
TOTAL SENS.
13 SEER HP WITH VARIABLE SPEED FURNACES2

556452-UTG-C-0611
Johnson Controls Unitary Products 11
GCGD42S41S3
T*(8,L)X*B12 FC/MC/PC43B 17 1300 42.0 29.0 13.50 11.50
T*(8,L)X*C16 FC/MC/PC43C 21 1475 42.0 29.9 13.50 11.50
T*(8,L)X*C20 FC/MC/PC43C 21 1415 42.0 29.5 13.50 11.50
T*9X*B12 FC/MC/PC43B 17 1270 42.0 29.0 13.50 11.50
T*9X*C16 FC/MC/PC43C 21 1410 42.0 29.6 13.30 11.00
T*9X*C20 FC/MC/PC43C 21 1400 42.0 29.6 13.50 11.00
T*(8,L)X*C16 FC/MC/PC48C 21 1360 42.0 29.5 13.80 11.50
T*(8,L)X*C20 FC/MC/PC48C 21 1475 42.0 30.1 14.00 11.50
T*9X*C16 FC/MC/PC48C 21 1425 42.0 29.3 13.50 11.50
T*9X*C20 FC/MC/PC48C 21 1420 42.0 29.3 13.50 11.50
T*9X*D20 FC/MC/PC48D 24 1435 42.0 29.7 13.50 11.50
T*(8,L)X*C16 UC48C 21 1400 42.0 29.4 13.50 11.00
T*(8,L)X*C20 UC48C 21 1515 42.0 30.0 13.50 11.00
T*9X*C16 UC48C 21 1425 41.5 29.2 13.30 11.00
T*9X*C20 UC48C 21 1420 42.0 29.4 13.20 11.00
T*9X*D20 UC48D 24 1435 42.0 29.4 13.40 11.00
(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 21 1425 42.0 30.0 13.50 11.50
(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 21 1450 42.0 30.4 13.50 11.50
(T*9C/T*9V)*C16 FC/MC/PC43C 21 1360 42.0 29.6 13.30 11.00
(T*9C/T*9V)*C20 FC/MC/PC43C 21 1395 42.0 29.6 13.50 11.00
(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 21 1435 42.0 30.1 13.80 11.50
(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 21 1410 42.0 30.1 14.00 11.50
(T*9C/T*9V)*C16 FC/MC/PC48C 21 1395 42.0 30.3 13.50 11.50
(T*9C/T*9V)*C20 FC/MC/PC48C 21 1430 42.0 30.3 13.50 11.50
(T*9C/T*9V)*D20 FC/MC/PC48D 24 1450 42.0 29.9 13.80 11.50
(T*(8,L)C/T*8V)*C16 UC48C 21 1435 41.5 30.2 13.50 11.00
(T*(8,L)C/T*8V)*C20 UC48C 21 1410 41.5 30.2 13.50 11.50
(T*9C/T*9V)*C16 UC48C 21 1395 41.5 30.2 13.30 11.00
(T*9C/T*9V)*C20 UC48C 21 1430 41.5 30.0 13.20 11.00
(T*9C/T*9V)*D20 UC48D 24 1450 41.5 30.2 13.40 11.00
GCGD48S41S3
T*(8,L)X*C16 FC/MC/PC48C 21 1600 48.0 34.4 13.30 11.00
T*(8,L)X*C20 FC/MC/PC48C 21 1660 48.0 34.4 13.20 11.00
T*9X*C16 FC/MC/PC48C 21 1565 48.0 34.8 13.10 11.00
T*9X*C20 FC/MC/PC48C 21 1615 48.0 34.4 13.20 11.00
T*9X*D20 FC/MC/PC48D 24 1635 48.0 34.8 13.20 11.00
T*(8,L)X*C16 FC/PC60C 21 1605 48.0 34.6 13.30 11.00
T*(8,L)X*C20 FC/MC/PC60D 21 1595 48.0 34.8 13.30 11.00
T*9X*C16 FC/PC60C 21 1575 47.0 34.6 13.10 11.00
T*9X*C20 FC/PC60C 21 1625 47.0 34.6 13.10 11.00
T*9X*D20 FC/MC/PC60D 24 1490 47.5 33.8 13.20 11.00
(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 21 1565 48.0 35.0 13.30 11.00
(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 21 1640 48.0 35.0 13.20 11.00
(T*9C/T*9V)*C16 FC/MC/PC48C 21 1590 48.0 34.6 13.10 11.00
(T*9C/T*9V)*C20 FC/MC/PC48C 21 1655 48.0 34.8 13.20 11.00
(T*9C/T*9V)*D20 FC/MC/PC48D 24 1645 48.0 35.2 13.20 11.00
(T*9C/T*9V)*D20 FC/MC/PC60D 24 1615 48.0 35.0 13.20 11.00
(T*(8,L)C/T*8V)*C16 FC/PC60C 21 1600 48.0 35.0 13.30 11.00
(T*(8,L)C/T*8V)*C20 FC/PC60C 21 1625 48.0 35.0 13.50 11.50
(T*9C/T*9V)*C16 FC/PC60C 21 1590 48.0 35.2 13.10 11.00
(T*9C/T*9V)*C20 FC/PC60C 21 1655 48.0 35.2 13.10 11.00
For Notes See Page 12.
COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)
MODELS FURNACE
MODEL COIL MODEL1WCOOLING
RATED
CFM Net MBH SEER EER
TOTAL SENS.
13 SEER HP WITH VARIABLE SPEED FURNACES2

556452-UTG-C-0611
12 Johnson Controls Unitary Products
GCGD60S41S3
T*(8,L)X*C16 FC/PC60C 21 1605 56.5 37.8 13.50 11.00
T*(8,L)X*C20 FC/MC/PC60D 21 1690 57.0 37.8 13.50 11.00
T*9X*D20 FC/MC/PC60D 24 1630 56.5 37.8 13.30 11.00
T*9X*C20 FC/MC/PC60D 21 1645 56.5 37.8 13.30 11.00
T*(8,L)X*C20 FC/MC62D 21 1665 57.0 37.8 13.50 11.00
T*(8,L)X*C16 UC60C 21 1640 56.0 37.2 13.00 11.00
T*(8,L)X*C20 UC60D 21 1735 56.5 38.5 13.00 11.00
T*9X*C16 FC/PC60C 21 1575 56.0 37.2 13.00 11.00
T*9X*C20 FC/PC60C 21 1560 56.0 37.2 13.00 11.00
T*9X*D20 UC60D 24 1630 56.0 37.2 13.00 11.00
T*(8,L)X*C20 UC60D 21 1735 56.5 38.5 13.00 11.00
T*9X*C20 UC60D 21 1645 56.0 37.2 13.00 11.00
(T*9C/T*9V)*D20 FC/MC/PC60D 24 1615 55.5 36.8 13.30 11.00
(T*(8,L)C/T*8V)*C20 FC/MC62D 21 1615 56.5 37.4 13.50 11.00
(T*9C/T*9V)*C20 FC/MC62D 21 1655 56.0 37.2 13.20 11.00
(T*9C/T*9V)*D20 FC/MC62D 24 1630 56.0 37.4 13.30 11.00
(T*(8,L)C/T*8V)*C20 FC/PC60C 21 1605 55.5 37.0 13.50 11.00
(T*9C/T*9V)*C20 FC/PC60C 21 1655 55.0 36.8 13.30 11.00
(T*(8,L)C/T*8V)*C20 UC60C 21 1605 54.0 35.2 13.00 11.00
(T*9C/T*9V)*C20 UC60C 21 1655 53.5 35.0 13.00 10.80
(T*9C/T*9V)*D20 UC60D 24 1615 53.5 35.0 13.00 10.90
1.MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.
2.Variable speed furnaces have B.O.D (Blower on Delay) standard.
COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)
MODELS FURNACE
MODEL COIL MODEL1WCOOLING
RATED
CFM Net MBH SEER EER
TOTAL SENS.
13 SEER HP WITH VARIABLE SPEED FURNACES2

556452-UTG-C-0611
Johnson Controls Unitary Products 13
ACCESSORIES
Refer to Price Manual for specific model numbers.
Off Cycle Timer Delay - Provides a 5-minute off cycle to pre-
vent rapid recycling of the compressor.
Hard Start Kit - Required when using TXV indoor coil. Also,
provides increased starting torque for areas with low voltage.
Thermostats - Compatible thermostat controls are available
through accessory sourcing. For optimum performance and
installation, refer to the UPGNET “Low Voltage Wiring Diagram”
document to select and apply controls.
SOUND POWER RATINGS*
* Rated in accordance with ARI 270-95 Standards.
TYPICAL INSTALLATION
TYPICAL FIELD WIRING
Model Source 1 Kit numbers
18 S1-2SA06708606
24 S1-2SA06721706
30 S1-2SA06705906
36 S1-2SA06708906
42 S1-2SA06708806
48 S1-2SA06708806
60 S1-2SA06707906
UNIT MODEL (dBA)
18 75
24 76
30 76
36 76
42 76
48 77
60 78
THERMOSTAT
SEAL OPENING(S) WITH
PERMAGUM OR EQUIVALENT
TO INDOOR COIL
TO FURNACE OR
AIR HANDLER
TERMINAL BLOCK
NEC CLASS 2 WIRING
NEC CLASS 1 WIRING
ALL OUTDOOR WIRING
MUST BE WEATHERPROOF. CONTROL
ACCESS
PANEL
WEATHERPROOF
DISCONNECT
SWITCH
MINIMUM 18 SERVICE
ACCESS CLEARANCE
ON ONE SIDE
60” OVERHEAD
CLEARANCE
10” CLEARANCE
AROUND PERIMETER
NOTE:
ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES
POWER WIRING
208/230-1-60
CONTACTOR
TERMINALS
COIL
GND.
LUG
CYRGW
YRGW
POWER WIRING
CONTROL WIRING
FACTORY WIRING
24 VOLT CONTROL WIRING
MINIMUM 18 GA. WIRE
(NEC CLASS 2)
FURNACE OR AIR HANDLER TERMINAL BLOCK
ROOM THERMOSTAT
CONDENSING UNIT
ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY.
TERMINAL W IS ONLY
REQUIRED ON SYSTEMS
WITH HEAT.
*
*

556452-UTG-C-0611
14 Johnson Controls Unitary Products
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature.
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD18S41S3
INDOOR COIL MODEL NO. FC/MC/PC18
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 450 600 750
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 16.3 18.4 18.3 20.1 20.7 17.5 19.0 18.7 20.2 20.9 18.7 19.6 19.1 20.3 21.1 S.C. 16.3 14.5 12.7 12.6 9.7 17.5 17.1 14.2 13.6 10.3 18.7 17.2 15.7 14.6 10.9
KW 1.16 1.16 1.16 1.15 1.14 1.21 1.21 1.21 1.20 1.20 1.26 1.26 1.27 1.26 1.25
75 T.C. 15.6 17.4 17.3 19.0 19.9 16.8 18.1 17.7 19.3 20.1 18.1 18.8 18.2 19.5 20.3 S.C. 15.6 14.3 12.2 12.2 9.3 16.8 16.3 13.8 13.4 10.1 18.1 18.4 15.4 14.6 10.8
KW 1.28 1.28 1.28 1.28 1.27 1.34 1.34 1.34 1.33 1.33 1.39 1.39 1.39 1.39 1.39
85 T.C. 14.8 16.4 16.2 18.0 19.2 16.1 17.2 16.7 18.4 19.3 17.4 18.0 17.3 18.8 19.5 S.C. 14.8 14.0 11.8 11.7 9.0 16.1 15.6 13.5 13.2 9.8 17.4 17.2 15.1 14.6 10.6
KW 1.40 1.41 1.40 1.41 1.41 1.46 1.46 1.46 1.46 1.47 1.52 1.52 1.52 1.52 1.52
95 T.C. 14.0 15.4 15.1 17.0 18.4 15.4 16.3 15.8 17.5 18.6 16.7 17.2 16.4 18.0 18.7 S.C. 14.0 13.8 11.3 11.3 8.6 15.4 14.8 13.1 13.0 9.6 16.7 15.9 14.9 14.6 10.5
KW 1.53 1.53 1.53 1.53 1.54 1.59 1.59 1.59 1.59 1.60 1.65 1.65 1.65 1.65 1.66
105 T.C. 13.0 14.2 13.7 15.6 17.1 14.3 15.1 14.3 16.1 17.3 15.5 16.1 15.0 16.6 17.4 S.C. 13.0 13.1 10.7 10.8 8.3 14.3 14.0 12.4 12.5 9.3 15.5 14.9 14.0 14.3 10.3
KW 1.69 1.69 1.69 1.70 1.71 1.75 1.75 1.75 1.76 1.77 1.82 1.82 1.81 1.82 1.83
115 T.C. 12.1 13.0 12.3 14.3 15.9 13.2 14.0 13.0 14.7 16.0 14.3 15.0 13.6 15.2 16.2 S.C. 12.1 12.4 10.1 10.3 8.0 13.2 13.1 11.7 12.1 9.0 14.3 13.8 13.2 13.9 10.1
KW 1.85 1.85 1.84 1.85 1.87 1.91 1.91 1.91 1.92 1.94 1.98 1.98 1.97 1.98 2.00
125 T.C. 11.1 11.9 10.9 12.9 14.7 12.1 12.9 11.6 13.4 14.8 13.1 13.9 12.3 13.8 14.9 S.C. 11.1 11.8 9.5 9.8 7.6 12.1 12.3 10.9 11.7 8.7 13.1 12.8 12.3 13.5 9.8
KW 2.00 2.00 1.99 2.01 2.04 2.08 2.07 2.06 2.08 2.10 2.15 2.14 2.13 2.15 2.16
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
– UC18 1.00 1.00 1.00
AHE18 –1.02 1.07 0.92
AHP18 –1.00 1.00 1.00
AHR18 –1.02 1.07 1.02
AHX18 –1.03 1.07 0.94
AV*24 –1.03 1.05 0.94
MV12B FC/MC18B 1.00 1.03 0.88
MX12B FC/MC/PC18B 1.02 1.05 0.90
F4FP024 –1.00 1.00 1.00
F6FP018 –1.02 1.03 0.93
Furnaces Coils T.C. S.C. KW
T*(8,L)X*A12 FC/MC/PC18A 1.01 1.00 0.89
T*(8,L)X*B12 FC/MC/PC18B 1.03 1.04 0.91
T*9X*B12 FC/MC/PC18B 1.03 1.04 0.91
T*(8,L)X*A12 UC18A 1.03 1.04 0.94
T*(8,L)X*B12 UC18B 1.03 1.04 0.94
T*9X*B12 UC18B 1.03 1.04 0.94
(T*(8,L)C/T*8V)*A12 FC/MC/PC18A 1.00 0.98 0.88
(T*(8,L)C/T*8V)*B12 FC/MC/PC18B 1.00 0.98 0.92
(T*9C/T*9V)*B12 FC/MC/PC18B 1.00 0.99 0.88
(T*(8,L)C/T*8V)*A12 UC18A 1.00 0.98 0.92
(T*(8,L)C/T*8V)*B12 UC18B 1.00 0.97 0.92
(T*9C/T*9V)*B12 UC18B 1.00 0.98 0.88

556452-UTG-C-0611
Johnson Controls Unitary Products 15
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed tem
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD24S41S3
INDOOR COIL MODEL NO. FC/MC/PC36
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 600 800 1000
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 20.5 25.5 25.4 27.0 28.2 22.6 26.7 26.5 28.3 29.5 24.7 28.0 27.7 29.6 30.8 S.C. 20.5 19.1 16.6 16.3 13.3 22.6 22.0 18.8 18.0 14.2 24.7 24.9 21.0 19.7 15.1
KW 1.66 1.67 1.67 1.67 1.67 1.73 1.74 1.74 1.74 1.74 1.81 1.81 1.82 1.82 1.82
75 T.C. 19.1 23.5 23.4 25.5 27.2 21.4 25.0 24.7 26.9 28.6 23.7 26.4 26.0 28.2 29.9 S.C. 19.1 18.5 15.7 15.8 12.8 21.4 21.1 18.0 17.6 13.8 23.7 23.8 20.4 19.4 14.9
KW 1.79 1.80 1.80 1.81 1.82 1.87 1.87 1.88 1.89 1.90 1.95 1.95 1.95 1.97 1.98
85 T.C. 17.7 21.6 21.3 24.0 26.3 20.2 23.2 22.8 25.4 27.6 22.7 24.8 24.3 26.9 28.9 S.C. 17.7 17.9 14.9 15.3 12.3 20.2 20.3 17.3 17.2 13.5 22.7 22.7 19.7 19.1 14.6
KW 1.92 1.92 1.92 1.95 1.98 2.01 2.01 2.01 2.04 2.06 2.09 2.10 2.09 2.12 2.14
95 T.C. 16.3 19.6 19.3 22.5 25.3 19.0 21.5 21.0 24.0 26.7 21.7 23.3 22.6 25.5 28.0 S.C. 16.3 17.3 14.1 14.7 11.9 19.0 19.5 16.5 16.8 13.1 21.6 21.6 19.0 18.9 14.4
KW 2.05 2.05 2.05 2.09 2.14 2.14 2.15 2.14 2.18 2.22 2.24 2.24 2.23 2.27 2.30
105 T.C. 15.0 17.7 17.1 20.1 23.1 17.4 19.5 18.8 21.6 24.4 19.8 21.3 20.4 23.1 25.8 S.C. 15.0 15.9 13.1 13.8 11.1 17.4 17.8 15.3 15.9 12.5 19.8 19.8 17.4 18.0 13.9
KW 2.17 2.17 2.16 2.22 2.28 2.28 2.28 2.26 2.31 2.37 2.38 2.39 2.36 2.41 2.45
115 T.C. 13.8 15.8 15.0 17.9 20.9 15.9 17.6 16.6 19.3 22.2 18.0 19.4 18.3 20.7 23.6 S.C. 13.8 14.6 12.1 12.9 10.4 15.9 16.3 14.0 15.0 11.8 17.9 17.9 15.8 17.1 13.3
KW 2.29 2.29 2.27 2.34 2.41 2.41 2.41 2.38 2.44 2.51 2.53 2.53 2.49 2.54 2.60
125 T.C. 12.5 13.9 12.8 15.7 18.7 14.4 15.7 14.5 17.0 20.1 16.2 17.5 16.2 18.4 21.4 S.C. 12.5 13.4 11.2 12.0 9.6 14.4 14.7 12.7 14.1 11.2 16.1 16.4 14.3 16.2 12.8
KW 2.41 2.41 2.38 2.46 2.55 2.54 2.54 2.50 2.56 2.65 2.67 2.67 2.61 2.67 2.75
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
–FC/MC/PC32 1.00 1.00 1.00
–FC/MC/PC35 1.00 1.00 1.00
–FC/MC/PC37 1.00 1.00 1.00
–FC/MC/PC43 1.00 1.00 1.00
–UC36 1.00 1.00 1.00
AHE24 –1.02 1.04 0.93
AHE30 –1.02 1.04 0.93
AHE36 –1.05 1.11 0.92
AHP30 –1.00 1.01 1.00
AHR24 –0.99 0.99 0.99
AHX30 –1.00 1.01 0.92
AHX36 –1.00 1.01 0.92
AV*36 –1.00 1.04 0.92
MV12B FC/MC36B 1.00 1.04 0.92
MV12B FC/MC35B 1.00 1.04 0.92
MV12B FC/MC43B 1.00 1.04 0.92
MX12B FC/MC35B 1.03 1.04 0.91
MX12B FC/MC36B 1.01 1.01 0.91
MX12B FC/MC43B 1.03 1.02 0.90
F4FP36 –1.00 1.00 1.00
F6FP030 –1.00 1.01 0.93
F6FP036 –1.00 1.02 0.92
Furnaces Coils T.C. S.C. KW
T*(8,L)X*A12 FC/MC/PC32A 1.00 1.01 0.96
T*(8,L)X*B12 FC/MC/PC35B 1.00 1.02 0.92
T*9X*C16 FC/MC/PC35C 0.99 0.98 0.91
T*9X*C20 FC/MC/PC35C 1.00 1.02 0.92
T*(8,L)X*A12 FC/MC/PC36A 1.00 1.01 0.92
T*(8,L)X*B12 FC/MC/PC36B 1.00 1.01 0.92
T*9X*B12 FC/MC/PC36B 1.00 1.01 0.92
T*9X*C16 FC/MC/PC36C 1.00 1.01 0.92
T*9X*C20 FC/MC/PC36C 1.00 1.01 0.92
T*(8,L)X*A12 FC/MC/PC37A 1.00 1.02 0.92
T*(8,L)X*B12 FC/MC/PC43B 1.00 1.02 0.92
(T*(8,L)C/T*8V)*A12 FC/MC/PC32A 1.00 1.02 0.96
(T*(8,L)C/T*8V)*B12 FC/MC/PC35B 1.00 1.01 0.92
(T*9C/T*9V)*B12 FC/MC/PC35B 1.00 1.02 0.92
(T*(8,L)C/T*8V)*A12 FC/MC/PC36A 1.00 1.01 0.92
(T*(8,L)C/T*8V)*B12 FC/MC/PC36B 1.00 1.02 0.92
(T*9C/T*9V)*B12 FC/MC/PC36B 1.00 1.01 0.92
(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 1.00 1.02 0.92
(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 1.00 1.01 0.92
(T*9C/T*9V)*B12 FC/MC/PC43B 1.00 1.02 0.92
(T*(8,L)C/T*8V)*A12 UC36A 0.98 0.99 0.94
(T*(8,L)C/T*8V)*B12 UC36B 0.98 1.00 0.94
(T*9C/T*9V)*B12 UC36B 0.98 1.00 0.94

556452-UTG-C-0611
16 Johnson Controls Unitary Products
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed tem
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD30S41S3
INDOOR COIL MODEL NO. FC/MC/PC32
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 800 1000 1200
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 30.2 33.4 32.8 35.2 36.5 31.7 33.9 33.4 35.5 36.7 33.2 34.3 34.1 35.9 36.9 S.C. 28.9 26.3 22.1 21.6 16.3 30.3 29.5 24.0 23.0 17.4 31.8 32.6 25.9 24.4 18.5
KW 2.18 2.20 2.20 2.21 2.23 2.27 2.28 2.29 2.42 2.32 2.37 2.36 2.38 2.63 2.41
75 T.C. 28.0 30.7 30.0 32.9 34.7 29.7 31.5 30.7 33.3 34.8 31.3 32.4 31.5 33.8 35.0 S.C. 26.9 25.2 20.9 20.7 15.6 28.4 27.6 23.0 22.4 16.7 30.0 30.1 25.1 24.1 17.8
KW 2.36 2.37 2.37 2.40 2.43 2.46 2.47 2.47 2.49 2.53 2.56 2.56 2.56 2.58 2.62
85 T.C. 25.9 28.0 27.2 30.6 32.8 27.7 29.2 28.0 31.2 33.0 29.5 30.5 28.8 31.7 33.1 S.C. 24.8 24.0 19.8 19.8 15.0 26.5 25.8 22.0 21.8 16.1 28.2 27.5 24.3 23.8 17.1
KW 2.54 2.54 2.54 2.59 2.64 2.65 2.65 2.64 2.56 2.73 2.76 2.75 2.74 2.54 2.83
95 T.C. 23.8 25.3 24.5 28.3 31.0 25.7 26.9 25.3 29.0 31.1 27.6 28.6 26.2 29.7 31.3 S.C. 22.8 22.9 18.6 18.9 14.4 24.6 23.9 21.0 21.2 15.4 26.5 25.0 23.5 23.5 16.5
KW 2.72 2.72 2.71 2.78 2.84 2.84 2.83 2.81 2.64 2.94 2.95 2.94 2.92 2.49 3.04
105 T.C. 21.8 23.1 21.7 25.2 27.9 23.4 24.6 22.6 25.8 28.0 25.0 26.1 23.5 26.4 28.1 S.C. 20.9 21.1 17.4 17.7 13.4 22.4 22.2 19.3 19.3 14.5 24.0 23.3 21.3 20.8 15.7
KW 2.91 3.02 2.88 2.96 3.04 3.03 3.08 2.99 2.90 3.14 3.15 3.14 3.10 2.84 3.24
115 T.C. 19.8 21.1 19.1 22.2 25.0 21.2 22.4 19.9 22.7 25.0 22.6 23.6 20.8 23.2 25.0 S.C. 19.0 19.3 16.2 16.7 12.5 20.3 20.5 17.7 17.4 13.7 21.6 21.6 19.2 18.2 14.9
KW 3.10 3.31 3.05 3.14 3.23 3.22 3.33 3.17 3.16 3.33 3.34 3.34 3.29 3.18 3.43
125 T.C. 17.8 19.0 16.4 19.2 22.0 19.0 20.1 17.3 19.6 22.0 20.1 21.2 18.2 20.0 22.0 S.C. 17.1 17.5 15.1 15.6 11.6 18.2 18.7 16.1 15.6 12.9 19.2 20.0 17.1 15.6 14.2
KW 3.28 3.61 3.22 3.31 3.42 3.41 3.57 3.34 3.42 3.52 3.53 3.54 3.47 3.53 3.63
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
– FC/MC/PC35 1.00 1.00 1.00
– FC/MC/PC37 1.00 1.00 1.00
– FC/MC/PC43 1.00 1.00 1.00
AHE30 –1.01 1.02 0.95
AHE36 –1.04 1.05 0.94
AHP30 –1.00 1.00 1.00
AHP36 –1.00 1.00 1.00
AHR30 –1.01 1.06 1.01
AHR36 –1.03 1.05 1.03
AHX30 –1.01 1.06 0.95
AHX36 –1.03 1.06 0.95
AV*36 –1.03 1.04 0.95
MV12B FC/MC35B 1.00 1.03 0.92
MV16C FC/MC35C 1.03 1.03 0.95
MV12B FC/MC43B 1.00 1.03 0.92
MV16C FC/MC43C 1.03 1.03 0.95
MX12B FC/MC35B 1.03 1.08 0.95
MX16C FC/MC35C 1.03 1.06 0.91
MX12B FC/MC43B 1.05 1.10 0.94
MX16C FC/MC43C 1.04 1.04 0.92
F4FP040 –1.00 1.00 1.00
F6FP030 –1.01 1.03 0.97
F6FP036 –1.01 1.02 0.93
Furnaces Coils T.C. S.C. KW
T*(8,L)X*A12 FC/MC/PC32A 1.01 1.02 1.01
T*(8,L)X*B12 FC/MC/PC35B 1.03 1.09 0.99
T*(8,L)X*C16 FC/MC/PC35C 1.03 1.09 0.95
T*(8,L)X*C20 FC/MC/PC35C 0.99 0.98 0.91
T*9X*B12 FC/MC/PC35B 1.03 1.09 0.94
T*9X*C16 FC/MC/PC35C 1.03 1.07 0.94
T*(8,L)X*A12 FC/MC/PC37A 1.03 1.09 0.99
T*(8,L)X*B12 FC/MC/PC43B 1.03 1.09 0.95
T*(8,L)X*C16 FC/MC/PC43C 0.97 0.92 0.89
T*(8,L)X*C20 FC/MC/PC43C 1.02 1.01 0.94
T*9X*B12 FC/MC/PC43B 1.03 1.09 0.99
T*9X*C16 FC/MC/PC43C 1.03 1.09 0.95
T*9X*C20 FC/MC/PC43C 0.97 0.92 0.89
(T*(8,L)C/T*8V)*A12 FC/MC/PC32A 1.01 1.04 1.01
(T*(8,L)C/T*8V)*B12 FC/MC/PC35B 1.02 1.02 0.98
(T*9C/T*9V)*B12 FC/MC/PC35B 1.01 1.05 0.97
(T*(8,L)C/T*8V)*C16 FC/MC/PC35C 1.02 1.05 0.94
(T*(8,L)C/T*8V)*C20 FC/MC/PC35C 1.03 1.07 0.95
(T*9C/T*9V)*C16 FC/MC/PC35C 1.02 1.05 0.94
(T*9C/T*9V)*C20 FC/MC/PC35C 1.02 1.05 0.94
(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 1.03 1.04 0.98
(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 1.03 1.05 0.95
(T*9C/T*9V)*B12 FC/MC/PC43B 1.03 1.05 0.99
(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 1.03 1.05 0.95
(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 1.03 1.05 0.95
(T*9C/T*9V)*C16 FC/MC/PC43C 1.03 1.05 0.95
(T*9C/T*9V)*C20 FC/MC/PC43C 1.03 1.05 0.95

556452-UTG-C-0611
Johnson Controls Unitary Products 17
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed tem
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD36S41S3
INDOOR COIL MODEL NO. FC/MC/PC37
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1000 1200 1400
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 35.3 37.4 37.0 39.3 40.4 36.3 38.1 37.4 39.7 40.2 37.3 38.8 37.8 40.1 40.1
S.C. 33.1 29.8 25.3 24.2 18.1 34.1 31.8 26.8 25.2 18.5 35.2 33.8 28.3 26.1 18.9
KW 2.40 2.42 2.41 2.44 2.44 2.49 2.50 2.50 2.53 2.53 2.58 2.58 2.60 2.61 2.63
75 T.C. 33.8 35.6 35.1 37.7 39.3 34.9 36.4 35.6 38.1 39.3 36.1 37.2 36.1 38.5 39.3
S.C. 31.7 29.4 24.8 23.9 17.9 32.9 31.4 26.5 25.1 18.5 34.1 33.3 28.2 26.3 19.1
KW 2.61 2.63 2.62 2.66 2.67 2.71 2.72 2.71 2.75 2.77 2.80 2.80 2.80 2.83 2.86
85 T.C. 32.4 33.8 33.3 36.2 38.1 33.6 34.7 33.8 36.6 38.3 34.8 35.6 34.4 37.0 38.4
S.C. 30.4 29.0 24.3 23.5 17.7 31.7 30.9 26.1 25.0 18.5 33.0 32.8 28.0 26.5 19.3
KW 2.82 2.84 2.84 2.88 2.91 2.92 2.93 2.92 2.96 3.00 3.02 3.03 3.01 3.05 3.09
95 T.C. 31.0 32.0 31.5 34.6 37.0 32.3 33.0 32.1 35.0 37.3 33.6 34.0 32.7 35.4 37.6
S.C. 29.0 28.6 23.7 23.1 17.5 30.5 30.5 25.8 24.9 18.5 31.9 32.3 27.9 26.6 19.5
KW 3.04 3.05 3.05 3.09 3.14 3.14 3.15 3.13 3.18 3.23 3.24 3.25 3.22 3.27 3.32
105 T.C. 28.0 28.9 27.8 31.1 34.3 28.9 29.9 28.5 31.6 34.6 29.9 30.9 29.2 32.0 34.9
S.C. 26.3 26.2 22.0 21.9 16.6 27.4 27.8 23.8 23.8 17.7 28.5 29.4 25.6 25.7 18.9
KW 3.25 3.25 3.23 3.30 3.37 3.36 3.36 3.33 3.39 3.47 3.47 3.47 3.43 3.49 3.56
115 T.C. 25.0 25.9 24.3 27.8 31.7 25.7 26.9 25.1 28.2 32.0 26.4 27.9 25.9 28.7 32.3
S.C. 23.7 23.9 20.3 20.8 15.8 24.4 25.2 21.8 22.8 17.0 25.2 26.6 23.4 24.7 18.3
KW 3.45 3.46 3.42 3.50 3.60 3.57 3.57 3.52 3.60 3.70 3.68 3.69 3.63 3.70 3.79
125 T.C. 22.1 22.9 20.7 24.4 29.0 22.5 23.9 21.7 24.9 29.3 22.9 24.9 22.6 25.4 29.6
S.C. 21.1 21.5 18.6 19.7 15.0 21.5 22.7 19.9 21.7 16.3 21.9 23.8 21.1 23.8 17.7
KW 3.65 3.66 3.60 3.70 3.83 3.78 3.78 3.71 3.80 3.93 3.90 3.91 3.83 3.91 4.03
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
–FC/MC/PC43 1.00 1.00 1.00
–FC/MC/PC48 1.00 1.00 1.00
–UC48 1.00 1.00 1.00
AHE36 –1.02 1.02 0.93
AHE42 –1.02 1.04 0.92
AHP36 –1.00 1.00 1.00
AHP42 –1.00 1.00 1.00
AHR36 –0.99 0.99 0.99
AHR42 –1.02 1.02 0.99
AHX36 –1.01 1.01 0.96
AHX42 –1.01 1.02 0.94
AV*36 –1.00 1.02 0.92
MV12B FC/MC43B 1.01 1.02 0.95
MV16C FC/MC43C 1.03 1.02 0.94
MV16C FC/MC48C 1.03 1.02 0.94
MV20D FC/MC48D 1.03 1.03 0.94
MV12D FC/MC48D 1.00 1.02 0.92
MX12B FC/MC43B 1.01 1.02 0.95
MX16C FC/MC43C 1.01 1.01 0.91
MX12D FC/MC48D 1.03 1.03 0.92
MX16C FC/MC48C 1.03 1.03 0.91
F5FP048 –1.00 1.00 1.00
F6FP042 –1.02 1.04 0.98
Furnaces Coils T.C. S.C. KW
T*(8,L)X*A12 FC/MC/PC37A 1.01 1.02 0.98
T*(8,L)X*B12 FC/MC/PC43B 1.01 1.02 0.98
T*(8,L)X*C16 FC/MC/PC43C 1.01 1.00 0.96
T*(8,L)X*C20 FC/MC/PC43C 1.02 1.03 0.96
T*9X*B12 FC/MC/PC43B 1.01 1.02 0.98
T*9X*C16 FC/MC/PC43C 1.01 1.02 0.98
T*9X*C20 FC/MC/PC43C 1.00 0.99 0.96
T*(8,L)X*C16 FC/MC/PC48C 1.02 1.02 0.97
T*(8,L)X*C20 FC/MC/PC48C 1.02 1.04 0.98
T*9X*C16 FC/MC/PC48C 1.02 1.04 0.98
T*9X*C20 FC/MC/PC48C 1.01 1.01 0.97
T*9X*D20 FC/MC/PC48D 1.01 1.01 0.97
T*(8,L)X*C16 UC48C 0.98 1.00 0.93
T*(8,L)X*C20 UC48C 0.99 1.02 0.95
T*9X*C16 UC48C 0.99 1.00 0.97
T*9X*C20 UC48C 0.97 0.99 0.95
T*9X*D20 UC48D 0.97 0.99 0.95
(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 0.97 0.93 0.97
(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 1.01 1.02 1.01
(T*9C/T*9V)*B12 FC/MC/PC43B 1.01 1.02 1.01
(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 1.02 1.02 0.97
(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 1.02 1.02 0.93
(T*9C/T*9V)*C16 FC/MC/PC43C 1.01 1.02 0.97
(T*9C/T*9V)*C20 FC/MC/PC43C 1.02 1.02 0.97
(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 1.03 1.05 0.94
(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 1.03 1.05 0.94
(T*9C/T*9V)*C16 FC/MC/PC48C 1.03 1.05 0.98
(T*9C/T*9V)*C20 FC/MC/PC48C 1.03 1.07 0.98
(T*9C/T*9V)*D20 FC/MC/PC48D 1.03 1.06 0.94
(T*(8,L)C/T*8V)*C16 UC48C 0.99 1.00 0.95
(T*(8,L)C/T*8V)*C20 UC48C 0.99 1.00 0.95
(T*9C/T*9V)*C16 UC48C 0.99 1.00 0.95
(T*9C/T*9V)*C20 UC48C 1.00 1.03 1.00
(T*9C/T*9V)*D20 UC48D 0.99 1.01 0.95
Furnaces Coils T.C. S.C. KW

556452-UTG-C-0611
18 Johnson Controls Unitary Products
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed tem
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD42S41S3
INDOOR COIL MODEL NO. FC/MC/PC43
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1200 1400 1600
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 43.6 44.7 42.9 46.2 47.7 45.1 45.7 44.3 47.7 49.0 46.7 46.7 45.7 49.3 50.2 S.C. 40.8 35.0 29.2 28.2 21.1 42.2 36.9 30.9 29.7 22.5 43.6 38.7 32.6 31.2 23.8
KW 2.89 2.90 2.90 2.91 2.96 2.97 2.98 2.98 3.00 3.04 3.04 3.06 3.06 3.09 3.12
75 T.C. 41.6 42.2 40.5 44.4 45.8 43.4 43.6 42.0 45.8 47.1 45.3 44.9 43.5 47.3 48.3 S.C. 38.7 34.6 28.7 28.0 20.9 40.4 36.8 30.6 29.6 22.0 42.2 39.0 32.5 31.2 23.2
KW 3.14 3.15 3.15 3.18 3.24 3.23 3.23 3.23 3.27 3.32 3.31 3.32 3.32 3.36 3.41
85 T.C. 39.6 39.6 38.2 42.6 43.9 41.7 41.4 39.7 43.9 45.2 43.9 43.2 41.2 45.2 46.4 S.C. 36.6 34.1 28.2 27.7 20.8 38.6 36.7 30.3 29.5 21.6 40.7 39.3 32.4 31.3 22.5
KW 3.39 3.39 3.40 3.46 3.51 3.49 3.49 3.48 3.55 3.61 3.58 3.58 3.57 3.64 3.70
95 T.C. 37.6 37.1 35.9 40.8 42.0 40.0 39.3 37.4 42.0 43.3 42.5 41.4 38.9 43.2 44.5 S.C. 34.4 33.7 27.6 27.5 20.6 36.9 36.6 29.9 29.4 21.2 39.3 39.6 32.3 31.3 21.8
KW 3.64 3.64 3.64 3.73 3.79 3.75 3.74 3.74 3.82 3.89 3.85 3.84 3.83 3.91 3.99
105 T.C. 34.7 34.1 32.2 36.8 38.0 36.9 36.1 33.6 37.9 39.1 39.1 38.1 35.1 39.1 40.2 S.C. 31.8 31.6 26.1 25.9 19.2 33.9 33.9 28.3 28.0 20.1 36.1 36.3 30.5 30.0 20.9
KW 3.89 3.89 3.88 3.97 4.08 4.01 4.00 3.97 4.07 4.18 4.12 4.11 4.07 4.17 4.28
115 T.C. 31.9 31.2 28.7 32.8 34.2 33.9 33.1 30.0 34.0 35.1 35.9 34.9 31.3 35.1 36.1 S.C. 29.2 29.5 24.6 24.4 17.9 31.1 31.4 26.7 26.5 18.9 32.9 33.2 28.9 28.6 20.0
KW 4.14 4.14 4.10 4.21 4.36 4.26 4.25 4.20 4.32 4.46 4.38 4.37 4.30 4.42 4.56
125 T.C. 29.1 28.3 25.1 28.9 30.4 30.9 30.0 26.3 30.0 31.1 32.6 31.7 27.5 31.2 31.9 S.C. 26.7 27.5 23.1 23.0 16.5 28.2 28.8 25.1 25.1 17.8 29.7 30.1 27.2 27.3 19.1
KW 4.39 4.38 4.33 4.45 4.64 4.51 4.51 4.43 4.56 4.74 4.64 4.63 4.53 4.67 4.85
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
– FC/MC/PC48 1.00 1.00 1.00
– UC48 1.00 1.00 1.00
AHE42 –1.02 1.04 0.94
AHP42 –0.98 1.00 0.98
AHR42 –1.01 1.05 1.01
AHX42 –1.00 1.02 0.92
AV*48 –1.00 1.02 0.92
AV*60 –1.00 1.02 0.92
MV16C FC/MC43C 1.00 1.03 0.92
MV16C FC/MC48C 1.00 1.03 0.92
MV20D FC/MC48D 1.00 1.03 0.92
MX16C FC/MC43C 1.01 1.03 0.93
MX16C FC/MC48C 1.02 1.04 0.92
MX20D FC/MC48D 1.02 1.03 0.94
F5FP048 –0.98 1.00 0.98
F6FP042 –1.00 1.03 0.94
F6FP048 –0.99 1.01 0.93
Furnaces Coils T.C. S.C. KW
T*(8,L)X*B12 FC/MC/PC43B 1.00 0.99 0.96
T*(8,L)X*C16 FC/MC/PC43C 1.00 1.02 0.96
T*(8,L)X*C20 FC/MC/PC43C 1.00 1.01 0.96
T*9X*B12 FC/MC/PC43B 1.00 0.99 0.96
T*9X*C16 FC/MC/PC43C 1.00 1.01 1.00
T*9X*C20 FC/MC/PC43C 1.00 1.01 1.00
T*(8,L)X*C16 FC/MC/PC48C 1.00 1.01 0.96
T*(8,L)X*C20 FC/MC/PC48C 1.00 1.03 0.96
T*9X*C16 FC/MC/PC48C 1.00 1.00 0.96
T*9X*C20 FC/MC/PC48C 1.00 1.00 0.96
T*9X*D20 FC/MC/PC48D 1.00 1.02 0.96
T*(8,L)X*C16 UC48C 1.00 1.01 1.00
T*(8,L)X*C20 UC48C 1.00 1.03 1.00
T*9X*C16 UC48C 0.99 1.00 0.99
T*9X*C20 UC48C 1.00 1.01 1.00
T*9X*D20 UC48D 1.00 1.01 1.00
(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 1.00 1.03 0.96
(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 1.00 1.04 0.96
(T*9C/T*9V)*C16 FC/MC/PC43C 1.00 1.01 1.00
(T*9C/T*9V)*C20 FC/MC/PC43C 1.00 1.01 1.00
(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 1.00 1.03 0.96
(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 1.00 1.03 0.96
(T*9C/T*9V)*C16 FC/MC/PC48C 1.00 1.04 0.96
(T*9C/T*9V)*C20 FC/MC/PC48C 1.00 1.04 0.96
(T*9C/T*9V)*D20 FC/MC/PC48D 1.00 1.02 0.96
(T*(8,L)C/T*8V)*C16 UC48C 0.99 1.03 0.99
(T*(8,L)C/T*8V)*C20 UC48C 0.99 1.03 0.95
(T*9C/T*9V)*C16 UC48C 0.99 1.03 0.99
(T*9C/T*9V)*C20 UC48C 0.99 1.03 0.99
(T*9C/T*9V)*D20 UC48D 0.99 1.03 0.99
Furnaces Coils T.C. S.C. KW

556452-UTG-C-0611
Johnson Controls Unitary Products 19
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed tem
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD48S41S3
INDOOR COIL MODEL NO. FC/MC/PC48
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1400 1600 1800
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 49.7 51.4 50.5 55.8 54.6 52.0 53.1 51.9 56.3 55.4 54.4 54.7 53.2 56.9 56.3 S.C. 46.9 42.8 35.7 35.7 25.9 48.8 45.6 37.9 37.1 27.3 50.8 48.3 40.1 38.5 28.8
KW 3.36 3.41 3.42 3.45 3.50 3.38 3.42 3.43 3.46 3.52 3.41 3.43 3.45 3.47 3.53
75 T.C. 47.5 48.6 47.7 52.8 52.3 49.8 50.3 48.9 53.6 53.1 52.0 52.1 50.1 54.3 53.8 S.C. 44.6 41.7 34.7 34.6 25.2 46.6 44.5 36.9 36.3 26.6 48.6 47.2 39.0 37.9 27.9
KW 3.65 3.68 3.68 3.74 3.82 3.67 3.70 3.70 3.76 3.83 3.70 3.72 3.72 3.77 3.85
85 T.C. 45.4 45.8 44.8 49.9 50.1 47.5 47.6 46.0 50.8 50.7 49.7 49.4 47.1 51.7 51.3 S.C. 42.3 40.6 33.7 33.5 24.6 44.4 43.4 35.8 35.4 25.8 46.4 46.1 37.9 37.3 27.0
KW 3.93 3.95 3.95 4.04 4.14 3.97 3.98 3.97 4.06 4.15 4.00 4.01 3.99 4.08 4.17
95 T.C. 43.2 42.9 42.0 46.9 47.9 45.3 44.8 43.0 48.0 48.4 47.3 46.7 44.1 49.1 48.9 S.C. 40.1 39.6 32.7 32.4 23.9 42.1 42.3 34.8 34.6 25.0 44.2 45.0 36.9 36.7 26.1
KW 4.22 4.22 4.22 4.34 4.46 4.26 4.26 4.24 4.36 4.47 4.30 4.30 4.27 4.39 4.49
105 T.C. 39.8 39.3 37.3 42.4 43.5 41.6 41.1 38.4 43.4 44.0 43.4 42.8 39.5 44.3 44.5 S.C. 36.8 36.7 30.7 30.7 22.7 38.6 39.0 32.7 32.8 23.7 40.5 41.2 34.7 34.9 24.8
KW 4.52 4.52 4.49 4.62 4.77 4.57 4.57 4.52 4.65 4.79 4.61 4.61 4.55 4.67 4.81
115 T.C. 36.4 35.9 32.7 37.9 39.3 38.0 37.5 33.9 38.9 39.7 39.6 39.0 35.1 39.8 40.2 S.C. 33.6 34.0 28.7 29.0 21.5 35.2 35.7 30.6 31.1 22.5 36.9 37.4 32.5 33.1 23.6
KW 4.82 4.82 4.76 4.89 5.07 4.87 4.86 4.79 4.92 5.10 4.92 4.91 4.82 4.95 5.13
125 T.C. 33.1 32.4 28.1 33.5 35.0 34.5 33.8 29.4 34.4 35.5 35.9 35.3 30.6 35.2 35.9 S.C. 30.4 31.2 26.7 27.3 20.3 31.9 32.5 28.5 29.3 21.3 33.3 33.7 30.4 31.3 22.3
KW 5.11 5.11 5.02 5.17 5.38 5.17 5.16 5.06 5.20 5.41 5.22 5.21 5.09 5.23 5.44
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
–FC/MC/PC60 1.00 1.00 1.00
–UC48 1.00 1.00 1.00
–UC60 1.00 1.00 1.00
AHE48 –0.98 1.01 0.94
AHP48 –1.00 1.00 1.00
AHP60 –1.00 1.02 1.00
AHR48 –1.00 1.01 1.00
AHX48 –1.00 1.03 0.96
AV*48 –1.00 1.02 0.92
AV*60 –1.00 1.02 0.92
MV16C FC/MC48C 1.00 1.02 0.92
MV20D FC/MC48D 1.00 1.02 0.92
MV16C FC/PC60C 0.99 1.00 0.95
MV20D FC/MC60D 1.00 1.02 0.92
MX16C FC/MC48C 1.01 1.03 0.97
MX20D FC/MC48D 1.00 0.99 0.94
MX16C FC/PC60C 1.01 1.01 0.95
MX20D FC/MC60D 1.01 1.01 0.93
F5FP048 –1.00 1.00 1.00
F5FP060 –1.00 1.00 1.00
F6FP048 –0.98 1.01 0.95
F4FV060 –1.00 1.01 0.96
Furnaces Coils T.C. S.C. KW
T*(8,L)X*C16 FC/MC/PC48C 1.00 1.00 1.00
T*(8,L)X*C20 FC/MC/PC48C 1.00 1.00 1.00
T*9X*C16 FC/MC/PC48C 1.00 1.01 1.00
T*9X*C20 FC/MC/PC48C 1.00 1.00 1.00
T*9X*D20 FC/MC/PC48D 1.00 1.01 1.00
T*(8,L)X*C16 FC/PC60C 1.00 1.01 1.00
T*(8,L)X*C20 FC/MC/PC60D 1.00 1.01 1.00
T*9X*C16 FC/PC60C 0.98 1.01 0.98
T*9X*C20 FC/PC60C 0.98 1.01 0.98
T*9X*D20 FC/MC/PC60D 0.99 0.98 0.99
(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 1.00 1.02 1.00
(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 1.00 1.02 1.00
(T*9C/T*9V)*C16 FC/MC/PC48C 1.00 1.01 1.00
(T*9C/T*9V)*C20 FC/MC/PC48C 1.00 1.01 1.00
(T*9C/T*9V)*D20 FC/MC/PC48D 1.00 1.02 1.00
(T*9C/T*9V)*D20 FC/MC/PC60D 1.00 1.02 1.00
(T*(8,L)C/T*8V)*C16 FC/PC60C 1.00 1.02 1.00
(T*(8,L)C/T*8V)*C20 FC/PC60C 1.00 1.02 0.96
(T*9C/T*9V)*C16 FC/PC60C 1.00 1.02 1.00
(T*9C/T*9V)*C20 FC/PC60C 1.00 1.02 1.00

Subject to change without notice. Published in U.S.A. 556452-UTG-C-0611
Copyright © 2011 by Johnson Controls, Inc. All rights reserved. Supersedes: 556452-UTG-B-0510
Johnson Controls Unitary Products
5005 York Drive
Norman, OK 73069
Multipliers for determining the performance with other indoor sections.
NOTE: For dry bulb temperatures different than those listed (between 73-87 °F), sensible capacity increases by 1060 BTUH per 1000 CFM per
degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed tem
COOLING PERFORMANCE DATA
AIR CONDITIONER MODEL NO. GCGD60S41S3
INDOOR COIL MODEL NO. FC/MC/PC60
CONDENSING
ENTERING AIR
TEMPERATURE
IDCFM 1600 1800 2000
ID DB (°F) 80 80 75 80 80 80 80 75 80 80 80 80 75 80 80
ID WB (°F) 57 62 62 67 72 57 62 62 67 72 57 62 62 67 72
65 T.C. 55.5 61.1 59.4 62.4 64.9 57.7 62.9 60.1 63.8 66.9 59.9 64.7 60.8 65.3 68.8
S.C. 54.5 49.8 40.0 39.7 28.6 56.4 52.4 42.4 41.2 30.8 58.3 54.9 44.9 42.7 32.9
KW 3.68 3.73 3.74 3.76 3.80 3.77 3.81 3.81 3.85 3.88 3.86 3.90 3.89 3.94 3.95
75 T.C. 54.5 58.5 56.4 60.1 63.1 56.6 60.3 57.4 61.6 65.0 58.8 62.2 58.4 63.1 66.8
S.C. 52.1 48.7 39.2 38.7 28.5 53.9 51.3 41.6 40.4 30.4 55.8 53.9 44.1 42.1 32.4
KW 4.14 4.17 4.17 4.21 4.26 4.23 4.25 4.25 4.29 4.34 4.31 4.34 4.33 4.38 4.42
85 T.C. 53.4 55.9 53.3 57.7 61.4 55.5 57.8 54.7 59.3 63.1 57.7 59.7 56.0 60.8 64.8
S.C. 49.7 47.6 38.3 37.7 28.4 51.5 50.2 40.8 39.6 30.1 53.2 52.8 43.2 41.5 31.8
KW 4.59 4.61 4.60 4.66 4.71 4.68 4.69 4.69 4.74 4.80 4.77 4.77 4.77 4.82 4.89
95 T.C. 52.4 53.4 50.3 55.4 59.6 54.4 55.3 51.9 57.0 61.2 56.5 57.2 53.6 58.6 62.7
S.C. 47.3 46.5 37.5 36.7 28.4 49.0 49.1 40.0 38.8 29.8 50.6 51.8 42.4 40.9 31.2
KW 5.05 5.05 5.03 5.10 5.17 5.13 5.13 5.12 5.18 5.26 5.22 5.21 5.21 5.26 5.35
105 T.C. 49.4 50.0 46.7 51.7 55.4 51.7 52.0 48.3 53.3 57.2 54.0 53.9 50.0 54.9 58.9
S.C. 44.6 44.4 36.2 35.2 26.9 46.3 46.6 38.6 37.4 28.4 48.0 48.9 41.0 39.5 29.8
KW 5.64 5.63 5.61 5.70 5.78 5.73 5.72 5.70 5.78 5.87 5.83 5.81 5.80 5.86 5.97
115 T.C. 46.6 46.7 43.3 48.1 51.4 49.1 48.7 44.8 49.7 53.3 51.5 50.8 46.4 51.3 55.2
S.C. 42.0 42.3 34.9 33.8 25.4 43.7 44.2 37.3 36.1 27.0 45.5 46.1 39.7 38.3 28.5
KW 6.21 6.20 6.17 6.29 6.37 6.32 6.30 6.27 6.37 6.47 6.42 6.40 6.36 6.45 6.57
125 T.C. 43.7 43.5 39.8 44.5 47.3 46.4 45.5 41.3 46.1 49.4 49.1 47.6 42.9 47.7 51.5
S.C. 39.3 40.3 33.7 32.5 24.0 41.1 41.8 36.0 34.7 25.6 43.0 43.2 38.3 37.0 27.2
KW 6.79 6.77 6.73 6.87 6.96 6.90 6.88 6.83 6.95 7.06 7.01 6.98 6.93 7.03 7.16
NOTE: ALL CAPACITIES INCLUDE INDOOR FAN HEAT AT 1250 BTUH/1000 CFM.
Air Handlers Coils T.C. S.C. KW
–FC/MC62 1.00 1.00 1.00
–FC64 1.00 1.01 0.98
– UC60 1.00 1.00 1.00
AHE60 –1.03 1.03 0.98
AHP60 –1.00 1.00 1.00
AHR60 –1.00 1.00 1.00
AHX60 –1.03 1.04 0.98
AV*60 –1.02 1.01 1.02
MV20D FC/MC60D 1.00 1.00 1.00
MV20D FC/MC62D 1.00 1.00 1.00
MV20D FC64D 1.00 1.01 0.96
MX20D FC/MC60D 1.01 1.01 0.96
MX20D FC/MC62D 1.02 1.01 0.95
MX20D FC64D 1.03 1.03 0.94
F5FP060 –1.00 1.00 1.00
F6FP060 –1.01 1.01 0.96
F4FV060 – 1.00 1.00 1.00
Furnaces Coils T.C. S.C. KW
T*(8,L)X*C16 FC/PC60C 0.99 0.98 0.99
T*(8,L)X*C20 FC/MC/PC60D 1.00 0.98 1.00
T*9X*C16 FC/PC60C 0.99 0.98 0.99
T*9X*C20 FC/PC60C 0.99 0.98 0.99
T*9X*D20 FC/MC/PC60D 1.00 0.98 1.00
T*9X*C20 FC/MC/PC60D 0.98 0.97 0.98
T*(8,L)X*C20 FC/MC62D 0.99 1.00 0.99
T*(8,L)X*C16 UC60C 0.98 0.97 0.98
T*(8,L)X*C20 UC60D 0.98 0.97 0.98
T*9X*D20 UC60D 0.98 0.97 0.98
T*(8,L)X*C20 UC60D 0.99 1.00 0.99
T*9X*C20 UC60D 0.98 0.97 0.98
(T*9C/T*9V)*D20 FC/MC/PC60D 0.97 0.96 0.97
(T*(8,L)C/T*8V)*C20 FC/MC62D 0.99 0.97 0.99
(T*9C/T*9V)*C20 FC/MC62D 0.98 0.97 0.98
(T*9C/T*9V)*D20 FC/MC62D 0.98 0.97 0.98
(T*(8,L)C/T*8V)*C20 FC/PC60C 0.97 0.96 0.97
(T*9C/T*9V)*C20 FC/PC60C 0.96 0.96 0.96
(T*(8,L)C/T*8V)*C20 UC60C 0.95 0.91 0.95
(T*9C/T*9V)*C20 UC60C 0.94 0.91 0.96
(T*9C/T*9V)*D20 UC60D 0.94 0.91 0.95